A material to consider for outdoor parts. An enclosed printer is part of the setup.
Open in interactive comparison
Outdoor fittings, signage, automotive exterior trim and anything that has to hold colour and strength in sunlight
ABS with the butadiene rubber swapped for an acrylate that has no UV-vulnerable double bonds: after 1000 h of QUV exposure Stratasys measured yield strength falling only from 30.5 to 30.3 MPa. It warps and emits styrene like ABS.
ASA is an outdoor engineering polymer: its weather-resistant rubber phase helps exposed parts retain color and useful mechanical properties. That makes outdoor housings, signage and exterior fittings natural applications. Industrial use extends beyond printing: INEOS describes Luran S ASA as a weather-resistant capstock for PVC siding, soffits and roofing, where the surface layer protects the underlying structure from sunlight and fading.
These co-extruded products demonstrate the polymer family’s weathering niche, not the strength of a particular printed spool. FDM ASA still warps and develops cooling stress, and layer direction matters for loaded brackets. Its UV durability does not make a housing automatically waterproof, and strong solvents such as acetone attack the matrix.
Other — co-extrusion · INEOS Luran S ASA family over PVC · Manufacturer-listed applications
INEOS reports that siding manufacturers use Luran S ASA over a PVC substrate to improve weatherability, particularly for darker colors. This is an industrial surface-layer application, not a 3D-printed wall panel.
Other — co-extrusion · INEOS Luran S ASA family over PVC · Manufacturer-listed applications
INEOS lists Luran S over PVC roofing and foam soffits for UV resistance and color retention. The ASA supplies the weather-resistant surface while the substrate provides the broader product structure.
A sink organizer that covers an unused soap-dispenser hole. The uploader explicitly identifies the pictured print as ASA.
Listing note: “Pictured model was printed with ASA.”
Printables listing uploaded by FMG-3D · CC BY 4.0Original listing · Checked 2026-10-17. This is an uploader report, not an independent material test.Source image · Image bytes unchanged; displayed in full.
Representative catalog values. Check the exact grade and its linked conditions before using a setting.
230–270 across brands; Prusament 260 ± 10, Bambu Lab 240–270, PolyLite 230–260
230–270 across brands; Prusament 260 ± 10, Bambu Lab 240–270, PolyLite 230–260
75–110; Prusament 110 ± 5, Bambu Lab 80–100, PolyLite 75–95
75–110; Prusament 110 ± 5, Bambu Lab 80–100, PolyLite 75–95
Enclosure recommended
Enclosure recommended — Polymaker calls a chamber needed at ambient temperature, Bambu Lab requires an enclosed printer and rules out its P1P and A-series machines
80 °C for 8 h (Bambu Lab); 70 °C for 7 h (Polymaker)
80 °C for 8 h (Bambu Lab); 70 °C for 7 h (Polymaker)
Open a topic to explore the complete data. Each value keeps its original conditions, units and dated sources.
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Base polymer / chemistry | Acrylonitrile styrene acrylate — ABS with the butadiene rubber phase replaced by an acrylate rubber that has no UV-vulnerable double bonds | 2 sources
|
| Density (g/cm³) | 1.05 (Bambu Lab) to 1.13 (PolyLite ASA), ISO 1183; Prusament 1.07 | 3 sources
|
| Typical price (USD/kg) | 1 kg spools cluster near 30 | 3 sources
|
| Price range across brands (USD/kg) | 18–50 across brands; IEMAI 18, SUNLU 18, Ambrosia 23, Polymaker 26, Bambu Lab 30, YXPOLYER 30, Prusament 41, 3DXTech 50 | 9 sources
|
| Market availability (1–5) | Stocked by most mainstream brands | 4 sources
|
| Spool sizes & diameters | 1.75 and 2.85 mm; 0.8, 1, 4 and 10 kg spools | 3 sources
|
| Typical applications | Outdoor fittings, signage, automotive exterior trim and anything that has to hold colour and strength in sunlight | 2 sources
|
| Diameter tolerance (± mm) | ±0.04 (Prusament) | 1 source
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Nozzle temperature (°C) | 230–270 across brands; Prusament 260 ± 10, Bambu Lab 240–270, PolyLite 230–260 | 3 sources
|
| Bed temperature (°C) | 75–110; Prusament 110 ± 5, Bambu Lab 80–100, PolyLite 75–95 | 3 sources
|
| Enclosure / chamber requirement (1–5) | Enclosure recommended — Polymaker calls a chamber needed at ambient temperature, Bambu Lab requires an enclosed printer and rules out its P1P and A-series machines | 2 sources
|
| Recommended chamber temperature (°C) | 45–60 (Bambu Lab) | 1 source
|
| Part cooling fan | Low — Prusament 30 % within a 0–50 % range, Bambu Lab 0–80 %, PolyLite off | 3 sources
|
| Bed surface & adhesion aid | Satin, smooth PEI or powder-coated sheet with a glue stick; Prusa advises a 3 mm or taller brim on large parts | 2 sources
|
| Maximum volumetric flow (mm³/s; see test conditions) (mm³/s) | 10–16 (PrusaSlicer guidance for ABS/ASA) | 1 source
|
| Warping tendency (1–5) | High — enclosure needed for reliable large parts; Prusa recommends a tall brim and Bambu Lab attributes cracking to cooling stress exceeding interlayer adhesion | 2 sources
|
| Bed-adhesion difficulty (1–5) | Needs a specific surface plus adhesive | 2 sources
|
| Stringing / oozing tendency (1–5) | Slight | 1 source
|
| Overall printing difficulty (1–5) | Intermediate — dry filament and a tuned profile | 2 sources
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Nozzle hardness required (1–4) | Brass fine indefinitely | 1 source
|
| Abrasiveness (1–5) | Non-abrasive | 1 source
|
| Nozzle clog risk (1–5) | Low — no special hot-end required and clogging is not among the listed drawbacks; Prusa lists no drybox and no hardened nozzle | 2 sources
|
| Heat-creep / jam sensitivity (1–5) | Slightly sensitive | 1 source
|
| Hotend requirement | No special hot-end required | 1 source
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Moisture absorption (hygroscopicity) (1–5) | Moderate — 0.45 % saturated at 25 °C / 55 % RH (Bambu Lab) and 0.40 % equilibrium (Polymaker); Prusa measures only 0.17 % after 7 days at 22 % RH | 3 sources
|
| Equilibrium moisture content at ~50 % RH (%) | 0.45 saturated at 25 °C / 55 % RH (Bambu Lab); 0.40 equilibrium (Polymaker); 0.17 after 7 days at 24 °C / 22 % RH (Prusa) | 3 sources
|
| Drying temperature & time | 80 °C for 8 h (Bambu Lab); 70 °C for 7 h (Polymaker) | 2 sources
|
| Symptoms when wet | Bubbling and popping at the nozzle, stringing, rough surface and weak layers | 1 source
|
| Effect of moisture on strength | No dry-versus-conditioned figures are published for ASA; Polymaker groups the styrenics as moderate-sensitivity and the loss shows as poor layer adhesion rather than a stated strength delta | 1 source
|
| Storage requirement | Sealed with desiccant; Polymaker rates the styrenics moderate-sensitivity | 1 source
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Tensile strength (XY) (MPa) | 37 ± 3 (Bambu Lab) to 43.8 (PolyLite) printed XY, ISO 527; Prusament 42 ± 1 at yield; Formfutura quotes 47.5 at yield | 4 sources
|
| Young's modulus (MPa) | 2379 (PolyLite) to 2450 (Bambu Lab) printed XY, ISO 527; Prusament 1600, Formfutura 2020 | 4 sources
|
| Elongation at break (%) | 6.7 (PolyLite) to 9.2 (Bambu Lab) at break, printed XY, ISO 527; Formfutura quotes 15 at break, Prusament 3.4 at yield | 4 sources
|
| Flexural strength (MPa) | 64 ± 1 printed horizontal (Prusament, ISO 178); Bambu Lab 65 ± 5, PolyLite 73.4 | 3 sources
|
| Flexural modulus (MPa) | 1920 ± 130 (Bambu Lab) to 3206 (PolyLite) printed XY, ISO 178; Prusament 2000 | 3 sources
|
| Charpy impact, notched (kJ/m²) | 10.3 (PolyLite) to 19.6 (Bambu Lab) printed XY, ISO 179, notched; Prusament 12 ± 1, Formfutura 18 | 4 sources
|
| Other impact data | Charpy unnotched 25 ± 3 printed horizontal and 38 ± 11 printed vertical (Prusament, ISO 179-1); Bambu Lab 41.0 ± 2.3 printed XY | 2 sources
|
| Layer adhesion / Z tensile (MPa) | 11 ± 1 (Prusa interlayer adhesion test); 31 ± 4 (Bambu Lab) and 32 (PolyLite) printed Z tensile, ISO 527 | 3 sources
|
| Brittleness (1–5) | Tough — absorbs impact, yields before breaking | 2 sources
|
| Hardness (scale-specific) (Shore A / Shore D / Rockwell) | 78 Shore D (Prusa Polymers method) | 1 source
|
| Creep resistance / sustained load (1–5) | Moderate — no printed-ASA creep test found; Tg of 98 °C keeps room-temperature service far below softening, unlike PLA | 2 sources
|
| Fatigue / repeated-flex resistance (1–5) | Moderate — fatigue limit at 25 % of tensile strength (8 MPa) on printed specimens, the best of the four polymers in that study | |
| Elasticity / flexibility (1–5) | Rigid | 1 source
|
| Z strength as % of XY (%) | 84 (Bambu Lab, printed Z against XY tensile); 73 for PolyLite ASA | 2 sources
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| HDT at 0.45 MPa (°C) | 93 (Prusament) to 103 (PolyLite), ISO 75 at 0.45 MPa; Bambu Lab 100 | 3 sources
|
| HDT at 1.8 MPa (°C) | 86 (Prusament) to 100 (PolyLite), ISO 75 at 1.8 MPa; Bambu Lab 92 | 3 sources
|
| Glass transition (Tg) (°C) | 98 (PolyLite, DSC) | 1 source
|
| Melting point / Vicat (°C) | Amorphous — no melting point; Vicat 105 (PolyLite, ISO 306) | 1 source
|
| Continuous service temperature (°C) | 93 — Prusa publishes this as the temperature resistance of Prusament ASA | 1 source
|
| Thermal expansion (CTE) (µm/m·K) | 69 ± 17 in XY and 115 ± 24 in the build direction (printed, TMA, 40–70 °C) | 1 source |
| Flammability / UL 94 | Flammable; no UL 94 rating published for standard ASA | 1 source
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| UV resistance (1–5) | Excellent — designed for permanent outdoor use. After 1000 h of QUV exposure to ASTM G154 Stratasys measured yield strength falling only from 30.5 to 30.3 MPa and stress at break by 3.0 % | 1 source |
| Outdoor durability | 1000 h QUV per ASTM G154, cycling 8 h at 60 °C and 4 h at 50 °C with condensation: yield 30.5 → 30.3 MPa, stress at break 30.5 → 29.5 MPa, elongation 2.8 → 2.3 %, modulus 1.82 → 1.95 GPa | 1 source |
| Chemical resistance | Good against weak acids, weak alkalis, oils and grease; dissolved by acetone | 1 source
|
| Water / humidity resistance in service (1–5) | Good — minor absorption | 1 source
|
| Food contact | Not food safe | 1 source
|
| Biodegradability / compostability | Not biodegradable | 1 source
|
| Recyclability | Not accepted in household plastic collection | 1 source
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Fume toxicity (1–5) | High — hazardous VOC such as styrene; enclosure and filtration needed | |
| VOC emission rate (µg/min) | 12–113 styrene, the range measured across the styrenic filaments tested; ASA itself was not among them | |
| Ultrafine-particle emission rate (particles/min) | 2 × 10¹⁰ to 9 × 10¹⁰ median for ABS, the closest styrenic tested; ASA itself was not measured | |
| Hazardous species emitted | Styrene. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea. Azimi et al. measured styrene from every styrenic filament tested but did not test ASA itself | |
| Ventilation / filtration requirement (1–5) | Enclosure with carbon and HEPA filtration |
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Sanding & machining | Sands well and takes filler before painting | 1 source
|
| Gluing & solvent welding | Solvent-welds with acetone | 1 source
|
| Vapour / chemical smoothing | Acetone vapour smoothing works — ASA dissolves in acetone | 1 source
|
| Support material pairing | HIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS that also serves ASA | 1 source
|
| Dimensional accuracy & detail | Warping and cooling-stress cracking are the accuracy limits; Stratasys notes the matte finish as a deliberate aesthetic advantage | 2 sources
|
| Property and unit | Published value and conditions | Sources and dates |
|---|---|---|
| Soluble in | Acetone dissolves it (Polymaker); MEK, THF, ethyl acetate and the chlorinated solvents dissolve the styrenic backbone. | 2 sources
|
| Softened or crazed by | Limonene attacks some grades — Prusa reports Prusament ASA Orange flaking apart as layer adhesion fails. | 1 source
|
| Solvent welding & smoothing agent | Acetone vapour, ~20 min at 80 °C over 5 mm of liquid (15–40 min across brands); layer adhesion up, tensile slightly down. | 1 source
|
Values describe representative grades, not every spool. Manufacturer datasheets and independent tests retain their source labels and dates. Printed orientation, test method, conditioning and formulation can change results. Unknown values are —. A listed use is not a certification. Shore A, Shore D and Rockwell hardness are separate scales.
Historical USD/kg snapshots. Read each listing’s sale/from qualifiers, spool mass, source date, shipping and tax notes. Product figures are separate from the material summary.
$17.99 / 1 kg spool, store.sunlu.com, Aug 2026; every colour showed out of stock at the time of checking
Also offered on a 0.9 kg refill spool.
Open product listing ↗| Spool sizes & diameters | 1 kg net, about 395 m (0.9 kg refill spool); 1.75 and 3.0 mm |
|
|---|---|---|
| Diameter tolerance (± mm) | +/-0.02 |
|
| Nozzle temperature (°C) | 250-280 (250-260 at 50-100 mm/s, 260-280 at 100-200 mm/s) |
|
| Bed temperature (°C) | 90-110 |
|
| Drying temperature & time | 80 °C for 6–8 h (recommended) |
$18.00 / 1 kg spool, store.iemai3d.com, Aug 2026 (regular price $25.00)
Black, 1.75 mm.
Open product listing ↗| Spool sizes & diameters | 1.75 mm |
|
|---|
$22.99 / 1 kg spool (1 kg net, 1.75 mm), filastruder.com, Aug 2026
Handle ambrosia-asa-filament.
Open product listing ↗| Density (g/cm³) | 1.08–1.09 (ISO 1183) | |
|---|---|---|
| Spool sizes & diameters | 1 kg net on a cardboard spool; 1.75 mm | |
| Diameter tolerance (± mm) | 0.03 | |
| Nozzle temperature (°C) | 230–260 (Ambrosia recommends 250) | |
| Bed temperature (°C) | 100–115 (Ambrosia recommends 110) | |
| Recommended chamber temperature (°C) | 40–120 (Ambrosia recommends 45) | |
| Part cooling fan | 0–70 %, depending on cooling capability | |
| Tensile strength (XY) (MPa) | 42–45 (ISO 527; specimen type not stated) | |
| Elongation at break (%) | 9–12 (ISO 527; specimen type not stated) | |
| Flexural strength (MPa) | 75–79 (ISO 178; specimen type not stated) | |
| Flexural modulus (MPa) | 1200–1400 (specimen type not stated) | |
| Other impact data | Izod impact 19–20 kJ/m² (ISO 180; specimen type not stated) | |
| HDT at 0.45 MPa (°C) | 88 (ISO 75, 0.455 MPa) | |
| Support material pairing | HIPS releases as a soluble support |
$25.99 / 1 kg spool, Polymaker product catalogue, Aug 2026
Handle asa.
Open product listing ↗| Density (g/cm³) | 1.13 at 23 °C (ISO 1183) |
|
|---|---|---|
| Nozzle temperature (°C) | 230–260 |
|
| Bed temperature (°C) | 75–95 |
|
| Part cooling fan | Off |
|
| Equilibrium moisture content at ~50 % RH (%) | 0.40 equilibrium water absorption |
|
| Drying temperature & time | 70 °C for 7 h |
|
| Tensile strength (XY) (MPa) | 43.8 ± 0.8 (printed XY, ISO 527, 260 °C nozzle, 90 °C chamber) |
|
| Young's modulus (MPa) | 2379 ± 157 (printed XY, ISO 527) |
|
| Elongation at break (%) | 6.7 ± 0.6 (printed XY, ISO 527); 1.65 printed Z |
|
| Flexural strength (MPa) | 73.4 ± 2.1 (printed XY, ISO 178) |
|
| Flexural modulus (MPa) | 3206 ± 108 (printed XY, ISO 178) |
|
| Charpy impact, notched (kJ/m²) | 10.3 ± 0.4 (printed XY, notched, ISO 179); 6.7 printed Z |
|
| Layer adhesion / Z tensile (MPa) | 32 ± 1.8 (printed Z, ISO 527) |
|
| HDT at 0.45 MPa (°C) | 103 (ISO 75, 0.45 MPa) |
|
| HDT at 1.8 MPa (°C) | 100 (ISO 75, 1.8 MPa) |
|
| Glass transition (Tg) (°C) | 98 (DSC) |
|
| Melting point / Vicat (°C) | Vicat 105 (ISO 306) |
|
EUR 21.78 incl. tax / 0.85 kg spool = EUR 25.62/kg = $27.67/kg at 1.08 USD/EUR, sakata3d.com, Aug 2026
Sold on 850 g spools. Figures are injection-moulded bars; the sheet cites ISO 178 against its tensile-yield row, which appears to be a transcription slip.
Open product listing ↗| Density (g/cm³) | 1.07 (ISO 1183) |
|
|---|---|---|
| Diameter tolerance (± mm) | 0.03 |
|
| Nozzle temperature (°C) | 240–260 classic, 260–285 high-speed |
|
| Bed temperature (°C) | 100–110 |
|
| Maximum volumetric flow (mm³/s; see test conditions) (mm³/s) | 24 (0.4 mm nozzle at 285 °C) |
|
| Tensile strength (XY) (MPa) | 48 at yield (injection-moulded) |
|
| Young's modulus (MPa) | 2300 (injection-moulded, ISO 527) |
|
| Elongation at break (%) | 9 (injection-moulded, ISO 527) |
|
| Flexural strength (MPa) | 70 (injection-moulded, ISO 178) |
|
| Other impact data | 14 kJ/m² notched Izod, ISO 180/A (injection-moulded) |
|
| HDT at 0.45 MPa (°C) | 97–105 (injection-moulded, ISO 75) |
|
| Melting point / Vicat (°C) | 97–101 (Vicat, ISO 306) |
|
EUR 25.90 incl. VAT / 1 kg spool = $27.97/kg at 1.08 USD/EUR, primacreator.com, Aug 2026
Roundness stated as >= 95 %.
Open product listing ↗| Nozzle temperature (°C) | 230–255 |
|
|---|---|---|
| Bed temperature (°C) | 80–100 |
|
| Tensile strength (XY) (MPa) | 48 (ISO 527, specimen type not stated) |
|
| Young's modulus (MPa) | 2020 (ISO 527) |
|
| Elongation at break (%) | 15 (ISO 527) |
|
| Charpy impact, notched (kJ/m²) | 18 at 23 °C (ISO 179 notched, specimen type not stated) |
|
| Melting point / Vicat (°C) | 98 (Vicat, ISO 306) |
|
$29.99 / 1 kg spool, us.store.bambulab.com, Aug 2026
Density 1.05 g/cm³, HDT 100 °C at 0.45 MPa, notched Charpy 19.6 kJ/m².
Open product listing ↗| Density (g/cm³) | 1.05 (ISO 1183) |
|
|---|---|---|
| Tensile strength (XY) (MPa) | 37 ± 3 (printed XY, ISO 527) |
|
| Charpy impact, notched (kJ/m²) | 19.6 ± 1.8 (printed XY, ISO 179, notched) |
|
| HDT at 0.45 MPa (°C) | 100 (ISO 75, 0.45 MPa) |
|
$29.99 / 1 kg spool, yxpolyer.com, Aug 2026 (regular price $34.99)
Ten colours. Figures below are from the technical data sheet published on the product page.
Open product listing ↗| Density (g/cm³) | 1.08 |
|
|---|---|---|
| Diameter tolerance (± mm) | +/-0.04 |
|
| Nozzle temperature (°C) | 250-280 |
|
| Bed temperature (°C) | 80-100 (spool label states 100-110) |
|
| Tensile strength (XY) (MPa) | 44 (printed XY) |
|
| Elongation at break (%) | 2.8 (printed) |
|
| Flexural strength (MPa) | 73 (printed XY); 25 in Z |
|
| Flexural modulus (MPa) | 2028 (printed XY); 1608 in Z |
|
| Other impact data | Unnotched Izod 31 kJ/m² in XY, 4 kJ/m² in Z (printed) |
|
| HDT at 0.45 MPa (°C) | 96 (vendor heat deflection temperature, load not stated) |
|
EUR 22.76 incl. 21 % VAT / 0.75 kg spool = EUR 30.35/kg = $32.77/kg at 1.08 USD/EUR, shop.filament-pm.com, Aug 2026
Sold on 0.75 kg and 2 kg spools. Maker caps part cooling at 30 %.
Open product listing ↗| Density (g/cm³) | 1.07 (ISO 1183/B) |
|
|---|---|---|
| Diameter tolerance (± mm) | 0.05 |
|
| Nozzle temperature (°C) | 240–260 |
|
| Bed temperature (°C) | 100–110 |
|
| Flexural modulus (MPa) | 1800 (ISO 178) |
|
| Other impact data | 12 kJ/m² impact strength, ISO 179 (notch type and specimen not stated) |
|
| HDT at 0.45 MPa (°C) | 87 (ISO 75, load not stated) |
|
| Melting point / Vicat (°C) | 96 (Vicat, ISO 306) |
|
$32.99 / 1 kg spool, atomicfilament.com product catalogue, Aug 2026
Handle cool-gray-asa-filament.
Open product listing ↗| Spool sizes & diameters | 1 kg spool; 1.75 mm |
|
|---|---|---|
| Diameter tolerance (± mm) | 0.02 average diameter variation; roundness ±0.02 |
|
| Nozzle temperature (°C) | 240–260 |
|
| Bed temperature (°C) | 90–110 |
|
| Enclosure / chamber requirement (1–5) | Enclosure recommended |
|
$34.00 regular / 1 kg spool (listed at $30.00 on promotion), coex3d.com, Aug 2026
LG Chem L1912 UV-resistant grade. Figures are printed XY bars, 100 % infill, unannealed.
Open product listing ↗| Density (g/cm³) | 1.07 (ASTM D792) |
|
|---|---|---|
| Diameter tolerance (± mm) | 0.03 |
|
| Maximum volumetric flow (mm³/s; see test conditions) (mm³/s) | 14 (0.4 mm nozzle at 250 °C); 31.5 with a 0.6 mm nozzle |
|
| Shrinkage (%) | 0.40–0.70 (ASTM D955) |
|
| Tensile strength (XY) (MPa) | 49 at yield (printed XY, 100 % infill, unannealed, ASTM D638) |
|
| Young's modulus (MPa) | 2160 (printed XY, ASTM D638) |
|
| Elongation at break (%) | 25 (printed XY, ASTM D638) |
|
| Flexural strength (MPa) | 79 (printed XY, ASTM D790) |
|
| Other impact data | 175 J/m notched Izod, ASTM D256 (printed XY, unannealed) |
|
| HDT at 0.45 MPa (°C) | 86 (printed XY, ASTM D648) |
|
| Glass transition (Tg) (°C) | 95 (DSC) |
|
| Flammability / UL 94 | UL 94 HB at 1.5 mm (yellow card L1912) |
|
$32.99 / 800 g spool with NFC = $41.24/kg, printedsolid.com product catalogue, Aug 2026
Handle prusament-asa-jet-black-800g-nfc. Interlayer adhesion 11 ± 1 MPa; needs a 110 °C bed.
Open product listing ↗| Diameter tolerance (± mm) | ±0.04 |
|
|---|---|---|
| Bed temperature (°C) | 110 ± 5 |
|
| Layer adhesion / Z tensile (MPa) | 11 ± 1 (Prusa Polymers interlayer adhesion test) |
|
| Hardness (scale-specific) (Shore A / Shore D / Rockwell) | 78 Shore D |
|
$50.00 / 1 kg spool at 1.75 mm, 3dxtech.com product catalogue, Aug 2026
Handle 3dxmax-r-asa; some 2.85 mm colours list at $25.00.
Open product listing ↗| Density (g/cm³) | 1.07 (ISO 1183) |
|
|---|---|---|
| Spool sizes & diameters | 1 kg, 4 kg and 10 kg reels; 1.75 and 2.85 mm |
|
| Nozzle temperature (°C) | 235–255 |
|
| Bed temperature (°C) | 90–110 |
|
| Drying temperature & time | 80 °C for 4 h |
|
| Tensile strength (XY) (MPa) | 45 at break (printed XY flat, ISO 527, 245 °C nozzle, 100 % infill) |
|
| Young's modulus (MPa) | 2010 (printed XY flat, ISO 527) |
|
| Elongation at break (%) | 10 at break (printed XY flat, ISO 527) |
|
| Flexural strength (MPa) | 78 (printed XY flat, ISO 178) |
|
| Flexural modulus (MPa) | 2000 (printed XY flat, ISO 178) |
|
| HDT at 0.45 MPa (°C) | 95 (ISO 75, 0.45 MPa) |
|
| Glass transition (Tg) (°C) | 105 (DSC) |
|
| Electrical & ESD properties | Surface resistance >10^13 Ω/sq (ASTM D257) — insulating |
|
Listed $24.99/1 kg; regular price unknown. Micro Center (Tustin, CA), 2026-10-17; excludes tax/shipping.
ASA product name and spool dimensions are explicit. Generic ABS copy on the retailer page is not reused as ASA mechanical data or printing settings.
Open product listing ↗| Spool sizes & diameters | 1 kg spool; 1.75 mm diameter (retailer listing) | |
|---|---|---|
| Diameter tolerance (± mm) | ±0.05 mm (retailer / package claim) |
Compare specific grades and connect test results to part design.
3D Printing Info