3D Printing InfoPrinter comparison
LulzBot TAZ Pro vs Voron Trident
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore LulzBot TAZ Pro comparisonsMore Voron Trident comparisons
| Property | LulzBot TAZ ProBEDSLINGER | Voron TridentCOREXY |
|---|---|---|
| Identity | ||
| Brand | LulzBot | Voron Design |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | LulzBot TAZ Pro (LulzBot's own store lists it under Legacy LulzBot printers)[1] | Voron Trident, current revision R2. Sold as "Voron Trident R2 3D Printer Kit by LDO"[2] |
| Street price (USD; dated snapshot per entry) | $4,950.00 on buy.lulzbot.com, in stock, checked Aug 2026[1] | $1,274.99 for the LDO kit at Fabreeko, on pre-order with a mid-to-late September ship estimate, checked Aug 2026. Fabreeko's live product feed shows the Trident kit at $1,199.99 and unavailable, so the figure depends on which variant is selected[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Several TAZ Pro derivatives exist and their specs differ substantially: TAZ Pro S, TAZ Pro XT+, and TAZ Pro Long Bed (282 x 582 x 285 mm, 1.2 mm GammaMaster steel nozzle, 80 °C bed cap, 150 mm/s travel, BLTouch 32-point mesh). The base TAZ Pro is 285 mm cubed with a 0.5 mm hardened-steel nozzle, a 110 °C bed and 300 mm/s travel — do not mix the two spec sets[1][4] | Two size variants on the LDO kit: Rev D 250 mm and Rev D+ 300 mm. Distinguished from the Voron 2.4 by the Z system: Trident has a fixed gantry with three Z motors lifting the bed, while the 2.4 lifts the gantry on four belted Z motors. Colour options black, space grey, blue[2][5] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 285 x 285 x 285 mm[1] | 250 x 250 x 250 mm or 300 x 300 x 300 mm depending on variant. Sortable value is the 300 mm kit[2] |
| Frame construction & material | Open frame; movement on GT2 belts with Igus SST rods and polymer bushings[1] | Aluminium-extrusion CoreXY frame, self-assembly[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | CoreXY with a fixed gantry; three independent Z stepper motors raise the bed and perform bed levelling[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Three independent Z stepper motors under the bed[2] |
| Belts (type, width, e.g. Gates?) | GT2 belt drive[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Trinamic TMC2130[1] | LDO Leviathan board: 5 x TMC2209 plus 2 x TMC5160 HV-capable drivers[2] |
| Speed & Acceleration | ||
| Max travel speed | 300 mm/s maximum travel speed (manufacturer figure)[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Pro Dual Extruder tool head — two active-lifting hot ends for true dual-material printing[1] | Bondtech Integrated Drive Gear Assembly (IGDA) with a Clockwork 2 motor[2] |
| Filament diameter | 2.85 mm standard, 1.75 mm optional[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | E3D Revo High Flow with a 60 W heater[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 290 °C maximum hot end temperature[1] | Not documented |
| Heater cartridge power (W) | Not documented | 60 W (E3D Revo High Flow heater in the LDO kit)[2] |
| Stock nozzle size & sizes included in box | 0.5 mm hardened steel[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Hardened steel[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 °C maximum bed temperature[1] | Not documented |
| Bed heater type (DC/AC mains) & wattage | 360 W, 24 V silicone bed heater[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Dual-sided borosilicate glass with PEI film[1] | LDO bed heater with a pre-installed magnet sheet and edge-to-edge heating[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 4-point mesh levelling using a 5 V contact circuit, plus automatic X-axis tramming, Z-offset and backlash compensation[1] | Omron inductive probe supplied; Klicky-mod parts also included in the kit[2] |
| Mesh grid size (probe point count — firmware evidence) | 4-point mesh[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament sensor with both runout and stripping detection[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[1] | LDO Leviathan control board; Nitehawk SB USB toolhead board with an integrated accelerometer[2] |
| PSU (brand, wattage, rail voltage) | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Marlin[1] | Klipper[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch full-colour resistive touchscreen[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB serial; a 16 GB flash drive is included for standalone printing[1] | Not documented |
| LED chamber/toolhead lighting | Not documented | COB LED chamber lighting included[2] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Self-assembly kit[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[1] | Not documented |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | FCC, CE, RCM, ETL, CSA, OSHWA and WEEE. The OSHWA listing is the open-hardware certification[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 1 year standard, with extended options. Made in the USA[1] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- Voron Trident R2 kit by LDO fabreeko.com · 2026-08 · vendor
- Fabreeko Voron collection product feed (live prices) fabreeko.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- Voron 2.4 R2 (Rev D+) kit by LDO fabreeko.com · 2026-08 · vendor