3D Printing InfoPrinter comparison
LulzBot TAZ Pro vs Voron 2.4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore LulzBot TAZ Pro comparisonsMore Voron 2.4 comparisons
| Property | LulzBot TAZ ProBEDSLINGER | Voron 2.4COREXY |
|---|---|---|
| Identity | ||
| Brand | LulzBot | Voron Design |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | LulzBot TAZ Pro (LulzBot's own store lists it under Legacy LulzBot printers)[1] | Voron 2.4, current revision R2, kits shipping as Rev D and Rev D+. Sold as "Voron 2.4 R2 (Rev D+) 3D Printer Kit by LDO"[2][3] |
| Street price (USD; dated snapshot per entry) | $4,950.00 on buy.lulzbot.com, in stock, checked Aug 2026[1] | $1,399.99 for the LDO Rev D+ kit at Fabreeko (300 mm and 350 mm are the same price), on pre-order with a mid-September estimate, checked Aug 2026. Fabreeko's live feed shows the base 2.4 kit listing at $1,299.99 and available. 3DJake lists an LDO 350 RevD kit but will not ship to the US[2][4][5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Several TAZ Pro derivatives exist and their specs differ substantially: TAZ Pro S, TAZ Pro XT+, and TAZ Pro Long Bed (282 x 582 x 285 mm, 1.2 mm GammaMaster steel nozzle, 80 °C bed cap, 150 mm/s travel, BLTouch 32-point mesh). The base TAZ Pro is 285 mm cubed with a 0.5 mm hardened-steel nozzle, a 110 °C bed and 300 mm/s travel — do not mix the two spec sets[1][6] | Sizes 250, 300 and 350 mm; LDO ships Rev D and Rev D+. Colours black, space grey, blue. Do not confuse with the Trident: the 2.4 lifts the whole gantry on four belted Z motors, the Trident lifts the bed on three screws. The Rev D+ kit includes a Raspberry Pi 4B; the older 3DJake-listed RevD kit explicitly does not include a Pi[2][3][5][7] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 285 x 285 x 285 mm[1] | 300 x 300 x 300 mm or 350 x 350 x 350 mm. Sortable value is the 350 mm kit[2][3][5] |
| Frame construction & material | Open frame; movement on GT2 belts with Igus SST rods and polymer bushings[1] | Blind-joint aluminium-extrusion frame with a complete panel set; stainless-steel linear rails throughout[3][5] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosed by the supplied panel set. A Nevermore Micro V5 internal circulation filter is included in the LDO kit[5] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | CoreXY on linear rails, with a belted flying gantry on four Z motors[3][2] |
| Belts (type, width, e.g. Gates?) | GT2 belt drive[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Trinamic TMC2130[1] | LDO Leviathan board: 5 x TMC2209 plus 2 x TMC5160 HV-capable drivers, ready for 48 V upgrades[2] |
| Speed & Acceleration | ||
| Max travel speed | 300 mm/s maximum travel speed (manufacturer figure)[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Pro Dual Extruder tool head — two active-lifting hot ends for true dual-material printing[1] | Clockwork 2 with a Bondtech BMG / Integrated Drive Gear Assembly, in a Stealthburner toolhead[2][3][5] |
| Filament diameter | 2.85 mm standard, 1.75 mm optional[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | E3D Revo Voron (24 V), all-metal, high-flow variant in the Rev D+ kit, with a 60 W heater; upgradeable to a Phaetus Rapido HF for $9.99[2][3][5] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 290 °C maximum hot end temperature[1] | Not documented |
| Heater cartridge power (W) | Not documented | 60 W (E3D Revo High Flow heater)[2] |
| Stock nozzle size & sizes included in box | 0.5 mm hardened steel[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Hardened steel[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 °C maximum bed temperature[1] | Not documented |
| Bed heater type (DC/AC mains) & wattage | 360 W, 24 V silicone bed heater[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Dual-sided borosilicate glass with PEI film[1] | Cast 5083 aluminium plate with a magnetic base and a powder-coated PEI sheet; LDO silicone bed heater with edge-to-edge heating[3][2][5] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 4-point mesh levelling using a 5 V contact circuit, plus automatic X-axis tramming, Z-offset and backlash compensation[1] | Omron inductive probe supplied; Klicky-mod parts included. Voron Tap is available as an add-on rather than standard[2][3] |
| Mesh grid size (probe point count — firmware evidence) | 4-point mesh[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament sensor with both runout and stripping detection[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[1] | LDO x Voron Leviathan mainboard (replacing the earlier BTT Octopus), plus a Nitehawk SB USB toolhead PCB[3][2][5] |
| PSU (brand, wattage, rail voltage) | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Marlin[1] | Klipper, hosted on a Raspberry Pi 4B (included in the Fabreeko Rev D+ kit, not in the older 3DJake RevD kit)[2][3][5] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch full-colour resistive touchscreen[1] | 4.3-inch touchscreen included in the LDO kit[5] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB serial; a 16 GB flash drive is included for standalone printing[1] | Not documented |
| LED chamber/toolhead lighting | Not documented | COB LED strips included[2][5] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Self-assembly kit; some parts must be printed by the user, and the LDO kit supplies pre-cut, pre-crimped cables and a heat-set insert soldering tip[5] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[1] | Not documented |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | FCC, CE, RCM, ETL, CSA, OSHWA and WEEE. The OSHWA listing is the open-hardware certification[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 1 year standard, with extended options. Made in the USA[1] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- Voron 2.4 R2 (Rev D+) kit by LDO fabreeko.com · 2026-08 · vendor
- LDO Voron 2.4 R2 (Rev D) kit listing matterhackers.com · 2026-08 · vendor
- Fabreeko Voron collection product feed (live prices) fabreeko.com · 2026-08 · vendor
- LDO Motors Voron 2.4 350 RevD kit contents 3djake.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- Voron Trident R2 kit by LDO fabreeko.com · 2026-08 · vendor