3D Printing InfoPrinter comparison
ELEGOO OrangeStorm Giga vs Original Prusa XL+ Single-Tool
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO OrangeStorm Giga comparisonsMore Original Prusa XL+ Single-Tool comparisons
| Property | ELEGOO OrangeStorm GigaINDUSTRIAL | Original Prusa XL+ Single-ToolCOREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Prusa Research |
| Class | INDUSTRIAL | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO OrangeStorm Giga[1] | Original Prusa XL+, Single-Tool variant ("Prusa XL+ Single-Tool" in the e-shop variant data)[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 17 October 2024 (Shopify publish date)[4] | The XL+ refresh was announced on 13 August 2026, on sale immediately in all toolhead configurations, with assembled printers shipping later in August 2026 and upgrade kits for existing XL owners from around the end of August. The original Original Prusa XL predates it[5] |
| Street price (USD; dated snapshot per entry) | $2,499.00 on us.elegoo.com, Aug 2026, against a compare-at price of $3,125.00[4] | $2,128.70 on prusa3d.com, Aug 2026 (lowest listed price for the Single-Tool variant; the Enclosure bundle starts at $2,610.19)[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Sold bare and in bundles; dual-printhead and quad-printhead upgrade kits are separate products, so a Giga's nozzle count depends on which kit was bought. The four printheads sit on the same X axis and print four copies of the same model in parallel (or the same model in four colours) - this is not an IDEX or a toolchanger[1][6] | The XL+ is sold in Single-Tool, Dual-Head and Five-Head variants at $2,128.70, $2,768.52 and $3,610.18 respectively (Aug 2026), plus Enclosure bundles and a Critical Infrastructure edition. The frame is the same in all of them - Prusa states the frame is ready for toolheads to be added at any time - so build volume, bed and electronics figures are shared and only the toolhead count and price differ. The XL+ is itself a revision of the Original Prusa XL: the older XL aligned toolheads with a mechanical pin, the XL+ uses a dedicated electronic sensor, adds a nozzle wiper and is claimed to print 10-15% faster[2][3] |
| Market position: superseded? successor announced? | Not documented | Current model; an Original Prusa XL to Prusa XL+ upgrade kit is sold for existing owners[3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 800 x 800 x 1000 mm; the platform is 820 x 820 mm made up of four independent 410 x 410 mm PEI plates[1] | 360 x 360 x 360 mm, which Prusa states as 46.7 litres[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 1224 x 1164 x 1425 mm; ELEGOO's maximum size for machine activity is 1224 x 1520 x 1570 mm. This is a floor-standing machine, not a desktop one[1] | About 700 x 900 x 720 mm (Prusa's own figure is approximate)[2] |
| Net weight (kg) | 104 kg net, 145 kg gross, and it ships in multiple crates (bottom + XY axis components, then two Z-axis components)[1] | About 30 kg[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame; the X and Y axes run on linear guides and the machine sits on carbon steel round bases with rubber anti-slip pads[1] | Aluminium extrusions and steel sheets (Prusa's comparison table for the XL)[7] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame. The Enclosure for Prusa XL+ is an optional add-on; Prusa says the printer is ready for chamber temperatures up to 60 C, that the new better-sealed enclosure reaches around 50 C on the printer's own waste heat, and that 60 C needs an upcoming chamber heater for which no shipping date has been given[2][5] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian gantry with a fixed bed - the printhead moves in X and Y on linear guides and the gantry moves in Z, so nothing about the bed moves during a print[1] | CoreXY with 1.5 mm GT belts, Input Shaper and Phase Stepping[2] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Linear guide on the X axis[1] | Not documented |
| Y-axis guide type | Linear guide on the Y axis[1] | Not documented |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Four lead screws with four linear guide rods[8] | Not documented |
| Belts (type, width, e.g. Gates?) | X/Y belts with knob-adjustable tensioners[1] | 1.5 mm GT belts[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)"; no driver part number published[8] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-300 mm/s, with 150 mm/s given by ELEGOO as the recommended speed - far below the 500-600 mm/s claimed for desktop machines, which is the honest consequence of moving a gantry this size[1][8] | Not documented |
| Recommended/typical print speed | 150 mm/s recommended printing speed (manufacturer figure)[8] | Not documented |
| Max acceleration (claimed, mm/s²) | 5000 mm/s2 maximum acceleration, which is also the default - four times lower than the Centauri machines[8] | Not documented |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | Not documented | Input Shaper and Phase Stepping[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans[8] | Nextruder direct drive; each toolhead carries its own extruder, hotend, nozzle and filament[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle - and note the standard diameter here is 0.6 mm, not the 0.4 mm used across the rest of the ELEGOO range[8] | Quick-swap nozzles - 0.25 mm for detail, 0.6/0.8 mm for speed, hardened steel for abrasives, high-flow CHT for throughput; toolheads ship with high-flow nozzles[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 290 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient, across four independent 410 x 410 mm PEI magnetic high-temperature platforms[1] | 120 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Four independent 410 x 410 mm PEI magnetic platforms rather than one large plate[1] | Segmented heatbed of 16 individually controlled tiles across the 360 x 360 mm surface, so only the tiles under the part are powered; removable double-sided satin print sheet supplied[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 100-point auto-levelling (the desktop ELEGOO machines use a 121-point mesh)[8][9] | Load-cell sensor - the nozzle is the probe, which Prusa says automatically accounts for nozzle changes, surface textures and thermal expansion and removes manual Z-offsets. Toolhead-to-toolhead alignment on the XL+ uses a separate permanently mounted eddy-current Tool Offset Sensor, replacing the removable mechanical pin used on the original XL[2][5] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection and power-loss resume printing[1] | Filament sensors fitted; Prusa's comparison table lists two filament sensors for the XL[7] |
| Multi-material/multi-color capability or official upgrade path | Up to three additional printheads can be added on the X axis for four-nozzle simultaneous printing - four copies of one model at once, or the same model in four colours[1] | Not documented |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Not documented | 360-degree part cooling on each toolhead, new on the XL+ and matching the MK4S and CORE One arrangement; Prusa states it delivers more airflow and distributes it more evenly around the nozzle. Additional fans and heatsinks cool the electronics. Fan sizes are not published[2][5] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | "Klipper High-Speed Quiet Motherboard" is all ELEGOO publishes[8] | Custom 32-bit xBuddy electronics with STM32 (Prusa's comparison table for the XL)[7] |
| Total rated power draw | 1530 W with a single head, plus 100 W per additional head, to a stated maximum of 1830 W with four nozzles; 100-120 VAC / 220-240 VAC, 50/60 Hz[1][8] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper[8] | Open-source firmware - Prusa states "Firmware: Open-source; ships with the full current Prusa feature set", and the XL is covered by the prusa3d/Prusa-Firmware-Buddy source tree[2][10] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 10.1-inch colour capacitive touch screen - by far the largest in the ELEGOO range[8] | 3.5-inch 65k-colour screen with touch control (Prusa's comparison table for the XL)[7] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer recommended, Orca and Cura supported[8] | On-device touch UI; Prusa Connect and the Prusa mobile app are optional - Prusa states the machine is fully offline capable[7][2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi, USB and LAN file transfer[1] | Ethernet, optional Wi-Fi; USB drive for print files. Prusa Connect optional and fully offline operation supported[2][7] |
| Materials Support | ||
| Officially supported filament list | The product page lists PLA, PETG and TPU; ELEGOO's compare page adds Nylon to the same machine. Either way it is a much shorter list than the Neptune bed-slingers[1][8] | PLA, PETG, ASA, ABS, PC, PA (nylon), TPU, PVA, HIPS, PP, CPE, PVB and carbon-fibre composites. Prusa states an open material policy - any brand of 1.75 mm filament, no chips and no subscriptions[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not documented | Open-source firmware on the xBuddy platform, which carries hardware overcurrent protection cutting heater and heatbed power above 15 A[11][10] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[13][7] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO OrangeStorm Giga product page (Specification table) us.elegoo.com · 2026-08 · vendor
- Original Prusa XL+ product page (spec block and variant price data) prusa3d.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- ELEGOO OrangeStorm Giga Shopify product JSON (price and store publish date) us.elegoo.com · 2026-08 · vendor
- Prusa blog - Better Prints, Easier Use: Prusa XL+, CORE One L+ and CORE One+ (Gen 2), Our Big Product Update (published 13 August 2026) blog.prusa3d.com · 2026-08 · doc
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- Prusa blog - Original Prusa MK4 is here (published 29 March 2023), including the MK4 specification table and launch prices blog.prusa3d.com · 2026-08 · doc
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc