3D Printing InfoPrinter comparison
ELEGOO Centauri Carbon 2 Combo vs Sovol SV08
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Centauri Carbon 2 Combo comparisonsMore Sovol SV08 comparisons
| Property | ELEGOO Centauri Carbon 2 ComboCOREXY | Sovol SV08COREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Sovol |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Centauri Carbon 2 Combo[1] | Sovol SV08 3D Printer[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 9 August 2026 (Shopify publish date)[4] | Not documented |
| Street price (USD; dated snapshot per entry) | $399.00 on us.elegoo.com, Aug 2026, against a compare-at price of $449.00[4] | $549.00 on sovol3d.com against a $599.00 compare-at price, in stock, checked Aug 2026 (Canada warehouse quoted as shipping end of September)[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | The Centauri Carbon 2 sold with the CANVAS multicolour unit. Every printing figure matches the bare Centauri Carbon 2; what changes is the body - 500 x 480 x 743 mm and 19.35 kg with CANVAS fitted - and CANVAS capability being listed Yes. Against the first-generation Centauri Carbon: 350 C nozzle rather than 320 C, clog detection added, and a HEPA plus coconut-shell carbon filter stack rather than the nano mineral crystal filter. An ELEGOO x emoji collaboration edition of the same machine is also listed[1][5][6][7] | Sibling SV08 Max is a much larger 500x500x500 machine at $1,099 with a 50 mm3/s flow rate, TMC5160 XY drivers and CAN bus; the SV08 is 30 mm3/s with TMC2209s. Do not carry SV08 Max figures onto the SV08. An eddy-current scanning kit and a 5-inch touchscreen are sold as separate upgrades[3][8][9][2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm; printing platform 260 x 260 mm[1] | 350 x 350 x 345 mm advertised[2][9] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 500 x 480 x 743 mm with the CANVAS unit fitted[1] | 550 x 537 x 575 mm. Sovol's page says this includes screen and filament holder; 3DJake says it excludes the spool holder[2][9] |
| Net weight (kg) | 19.35 kg net, 23.8 kg gross[1] | 21.5 kg gross (3DJake). Sovol does not publish a net weight[9] |
| Frame construction & material | Integrated die-cast aluminium construction (Centauri Carbon platform)[6] | Aluminium-extrusion CoreXY frame; Sovol states the design is inspired by the Voron 2.4 and that software, firmware and hardware are open source with design files on GitHub, with $2 per unit donated to the Voron project[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed; the Centauri Carbon 2 uses a HEPA plus granulated coconut-shell activated-carbon filter stack rather than the first generation's nano mineral crystal filter, and adds a smart exhaust grille[5][6] | Open frame as shipped; Sovol sells an enclosure kit separately (an enclosure-kit package is listed for the SV08 Max)[2][8] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY[1] | CoreXY[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Three lead screws with three linear guide rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)"; no driver part number published[1] | TMC2209[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s or less, with 250 mm/s given as the recommended speed[1] | 700 mm/s maximum (manufacturer claim)[2][9] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 maximum acceleration; default 10000 mm/s2[1] | 40,000 mm/s2 maximum (manufacturer claim)[2][9] |
| Max volumetric flow claimed (mm³/s) | Not documented | <=30 mm3/s (manufacturer claim)[2][9] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with one fan[1] | Planetary-gear direct-drive extruder[2][9] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass-hardened steel nozzle, 0.4 mm, titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 350 C claimed max nozzle temperature - 30 C above the first-generation Centauri Carbon[1][6] | <=300 °C claimed[2][9] |
| Stock nozzle size & sizes included in box | Not documented | 0.4 mm included; 0.2, 0.6 and 0.8 mm optional[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature at 25 C ambient[1] | <=100 °C claimed[2][9] |
| Bed surface (material, texture, coating), single/double-sided | Dual-sided spring steel sheet, textured PEI plus a PLA-specific surface[1] | Powder-coated PEI steel plate[2][9] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | 121-point auto-levelling with full-auto calibration[1] | Inductive sensor plus a pressure (load) sensor. An eddy-current scanning kit is sold as an upgrade[2][9][3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor, clog detection, auto filament unloading and power-loss recovery[1] | Filament sensor fitted, with filament-runout resume; type and location not published[2][9] |
| Multi-material/multi-color capability or official upgrade path | CANVAS multi-material capability included - the defining difference from the bare Centauri Carbon 2[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | "Powerful Self-Developed Motherboard" is all ELEGOO publishes[1] | Not documented |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | Allwinner H616 quad-core Cortex-A53, 1 GB RAM (512 MB + 512 MB), 8 GB eMMC[2][9] |
| PSU (brand, wattage, rail voltage) | Not documented | Conflicting: Sovol's spec table says 150 W / 24 V, while 3DJake's table gives a rated power of 1000 W at both 110 V and 220 V. The two are only reconcilable if the bed is mains-heated separately from the 24 V logic supply, which Sovol does not state[2][9] |
| Total rated power draw | 1100 W at 220 V, 350 W at 110 V rated; 24 V output[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | ELEGOO OS; ElegooSlicer recommended, Orca and Cura supported[1] | Klipper. Sovol publishes the design files on GitHub and describes software, firmware and hardware as fully open source[2][9] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch colour capacitive touch screen (the first-generation Centauri Carbon used a 4.3-inch panel)[1][6] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour touch UI; LED lighting fitted; STL, OBJ, 3MF and STEP input[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB and Wi-Fi[1] | Ethernet and Wi-Fi 2.4 GHz, WPA2 only (WPA3 explicitly not supported)[2][9] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Camera fitted[1] | Camera listed as fitted by Sovol; 3DJake lists a camera as an accessory. Resolution not published[2][9] |
| Materials Support | ||
| Officially supported filament list | Ideal: PLA, PETG, ABS, ASA. Capable: TPU, PC, PA, PET and fibre-reinforced filaments[1] | PLA, PETG, TPU, PETG-CF, ABS and others[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 45 dB or less - a manufacturer figure with no distance or method stated, and 10 dB below the first-generation Centauri Carbon's published figure[1][6] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[10] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- Sovol SV08 3D Printer product page sovol3d.com · 2026-08 · vendor
- Sovol 3D-printer collection product feed (live prices and stock) sovol3d.com · 2026-08 · vendor
- ELEGOO Centauri Carbon 2 Combo Shopify product JSON (price and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon 2 product page (Centauri Carbon 2 vs Centauri Carbon side-by-side table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- Sovol SV08 Max 3D Printer product page sovol3d.com · 2026-08 · vendor
- Sovol SV08 technical data table 3djake.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor