3D Printing InfoPrinter comparison
Bambu Lab H2D vs LulzBot TAZ Pro
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab H2D comparisonsMore LulzBot TAZ Pro comparisons
| Property | Bambu Lab H2DCOREXY | LulzBot TAZ ProBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | LulzBot |
| Class | COREXY | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab H2D[1] | LulzBot TAZ Pro (LulzBot's own store lists it under Legacy LulzBot printers)[2] |
| Street price (USD; dated snapshot per entry) | From $1,549.00 on the Bambu Lab US store, Aug 2026, against a stated typical price of $1,749.00; the product page shows $1,749.00 (typical $1,999.00) with a combo variant selected[3][4] | $4,950.00 on buy.lulzbot.com, in stock, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Six SKUs on one product page including H2D, H2D AMS Combo and H2D Laser Full Combo. The Laser Edition adds laser safety windows and the air-assist pump; a plain H2D can be upgraded with a Laser Upgrade Kit. The BirdsEye camera is only fitted on the Laser Edition. Siblings in the same family are the H2S (single nozzle, 340x320x340 mm, 30 kg) and H2C (dual nozzle, 305x320x325 mm single-nozzle volume, 32.5 kg, four cameras as standard) - all three share the 492x514x626 mm body, so body dimensions alone will not tell them apart[1][5][6] | Several TAZ Pro derivatives exist and their specs differ substantially: TAZ Pro S, TAZ Pro XT+, and TAZ Pro Long Bed (282 x 582 x 285 mm, 1.2 mm GammaMaster steel nozzle, 80 °C bed cap, 150 mm/s travel, BLTouch 32-point mesh). The base TAZ Pro is 285 mm cubed with a 0.5 mm hardened-steel nozzle, a 110 °C bed and 300 mm/s travel — do not mix the two spec sets[2][7] |
| Market position: superseded? successor announced? | Current model; the H2C sits above it in the same body at $2,199 and the H2S below it at $1,199[3] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | Single-nozzle printing 325 x 320 x 325 mm; dual-nozzle printing 300 x 320 x 320 mm; total volume across the two nozzles 350 x 320 x 320 mm. The sortable figure is the single-nozzle volume[1] | 285 x 285 x 285 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 492 x 514 x 626 mm[1] | Not documented |
| Net weight (kg) | 31 kg net[1] | Not documented |
| Frame construction & material | Aluminium, steel, plastic and glass chassis and shell[1] | Open frame; movement on GT2 belts with Igus SST rods and polymer bushings[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor; active chamber heating to 65 C, chamber exhaust and heat-circulation fans, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack[1] | Open frame, no enclosure[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Active chamber heating, maximum 65 C (manufacturer figure)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - not named in the spec sheet; Bambu groups the H2 series with its enclosed CoreXY machines at 20000 mm/s2[1] | Cartesian bedslinger[2] |
| Belts (type, width, e.g. Gates?) | Not documented | GT2 belt drive[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic TMC2130[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | Not documented |
| Max travel speed | Not documented | 300 mm/s maximum travel speed (manufacturer figure)[2] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s with the standard-flow hotend, 65 mm3/s with the optional high-flow hotend; both measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual direct-drive extruders with hardened-steel gears, driven by Bambu high-precision permanent-magnet synchronous motors[1] | Pro Dual Extruder tool head — two active-lifting hot ends for true dual-material printing[2] |
| Filament diameter | Not documented | 2.85 mm standard, 1.75 mm optional[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | All-metal hotend with hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; an optional high-flow hotend is offered[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 350 C claimed max nozzle temperature[1] | 290 °C maximum hot end temperature[2] |
| Stock nozzle size & sizes included in box | Not documented | 0.5 mm hardened steel[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 120 C max heatbed temperature[1] | 110 °C maximum bed temperature[2] |
| Bed heater type (DC/AC mains) & wattage | Not documented | 360 W, 24 V silicone bed heater[2] |
| Bed surface (material, texture, coating), single/double-sided | Textured PEI plate and Smooth PEI plate supported[1] | Dual-sided borosilicate glass with PEI film[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | Automatic 4-point mesh levelling using a 5 V contact circuit, plus automatic X-axis tramming, Z-offset and backlash compensation[2] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 4-point mesh[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1] | Filament sensor with both runout and stripping detection[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, auxiliary part-cooling fan, chamber heat-circulation fan, hotend cooling fan, main control board fan and chamber exhaust fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[2] |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; 2200 W at 220 V, 1320 W at 110 V. The US store page states the H2D it sells is the 100-120 V version[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[8] | Marlin[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 720x1280 touchscreen[1] | 5-inch full-colour resistive touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus Bambu Studio, Bambu Suite and Bambu Handy[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port[1] | USB serial; a 16 GB flash drive is included for standalone printing[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Four cameras listed: live view 1920x1080, nozzle camera 1920x1080, toolhead camera 1920x1080, and a 3264x2448 BirdsEye camera fitted only on the Laser Edition[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, TPU, PVA, BVOH, ABS, ASA, PC, PA, PET, plus carbon/glass-fibre reinforced PLA, PETG, PA, PET, PC, ABS, ASA, PPA-CF/GF, PPS and PPS-CF/GF[1] | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | Not documented | FCC, CE, RCM, ETL, CSA, OSHWA and WEEE. The OSHWA listing is the open-hardware certification[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[9] | 1 year standard, with extended options. Made in the USA[2] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification, not an independent measurement)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab H2D - Technical Specifications bambulab.com · 2026-08 · vendor
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab H2D store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab H2S & H2S Laser Edition Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab H2C Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor