3D Printing InfoPrinter comparison
Anycubic Kobra 3 Max vs LulzBot TAZ Pro Long Bed
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Anycubic Kobra 3 Max comparisonsMore LulzBot TAZ Pro Long Bed comparisons
| Property | Anycubic Kobra 3 MaxBEDSLINGER | LulzBot TAZ Pro Long BedBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Anycubic | LulzBot |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Anycubic Kobra 3 Max[1] | LulzBot TAZ Pro Long Bed 3D Printer[2] |
| Release date (announcement and actual shipping) | Listed on the Anycubic store from 19 February 2025 (Shopify publish date)[3] | Not documented |
| Street price (USD; dated snapshot per entry) | $429.00 with a US plug on store.anycubic.com, Aug 2026, against a compare-at price of $699.00 ($493.00 for the EU plug variant)[3] | $7,995.00 at MatterHackers, listed as currently unavailable, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Same 420 x 420 x 500 mm build volume as the older Kobra 2 Max, so build volume will not tell them apart - but the Kobra 3 Max is faster (600 mm/s claimed against 500), runs Kobra OS with multi-colour support and a 4.3-inch touchscreen, and is lighter at 19 kg against 21 kg. Its acceleration ceiling is 10000 mm/s2, half the 20000 mm/s2 of the smaller Kobra 3 - a difference the marketing does not lead with[1][4][5] | Not simply a longer TAZ Pro. The Long Bed ships the Asteroid 285 tool head with a 1.2 mm nozzle, a 0.3-0.9 mm equipped layer range, an 80 °C bed cap (vs 110 °C), 150 mm/s travel (vs 300) and BLTouch 32-point mesh levelling (vs 4-point contact). Bed material also differs: blue spring-steel magnetic flex rather than glass with PEI film[2][6] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 420 x 420 x 500 mm, which Anycubic states as 88 L[1] | 282 x 582 x 285 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 706 x 640 x 753 mm[1] | Not documented |
| Net weight (kg) | 19 kg[1] | Not documented |
| Frame construction & material | Not documented | Open frame; GT2 belt drive with Igus SST rods and polymer bushings[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Anycubic's table gives the construction as "Gantry System" - a bed-slinger, with dual Y-axis motors added to stop layer misalignment on the large moving bed[1] | Cartesian bedslinger[2] |
| Belts (type, width, e.g. Gates?) | Semi-automatic belt tensioning, which Anycubic pairs with motor anti-skip[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic TMC2130[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s maximum print speed (manufacturer claim), 300 mm/s recommended[1] | Not documented |
| Recommended/typical print speed | 300 mm/s recommended print speed (manufacturer figure)[1] | Not documented |
| Max travel speed | Not documented | 150 mm/s maximum travel speed, firmware-limited[2] |
| Max acceleration (claimed, mm/s²) | 10000 mm/s2 maximum acceleration - half the ceiling of the smaller Kobra 3, because of the moving mass[1][5] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive ("short distance extrusion") with a quick-release hotend[1] | Asteroid 285 tool head[2] |
| Filament diameter | Not documented | 2.85 mm standard, 1.75 mm optional[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | 300 C quick-release hotend with an aerospace-grade ceramic composite throat tube; 0.4 mm standard nozzle, expandable to 0.6 and 0.8 mm[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C maximum nozzle temperature[1] | 290 °C maximum, firmware-limited[2] |
| Stock nozzle size & sizes included in box | Not documented | 1.2 mm GammaMaster steel[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | GammaMaster steel[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 90 C maximum hotbed temperature on a PEI spring steel plate - 20 C below the smaller Kobra 3[1][5] | 80 °C maximum bed temperature — notably lower than the base TAZ Pro[2] |
| Bed heater type (DC/AC mains) & wattage | Not documented | 360 W, 24 V silicone bed heater[2] |
| Heat-up time to 60°C (measured preferred) | Anycubic claims the ultra-large hotbed heats up in 125 s; no target temperature is stated for that figure and it is a manufacturer claim, not a measurement[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Blue spring-steel magnetic flex bed system[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | LeviQ 3.0 auto-levelling with Z-offset and area levelling[1] | BLTouch, 32-point automatic mesh calibration[2] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 32 points[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection with auto resume, entanglement detection and power-loss resume[1] | Filament sensor with runout and stripping detection[2] |
| Multi-material/multi-color capability or official upgrade path | Supports 4- or 8-colour printing with ACE Pro units[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Kobra OS; Anycubic Slicer Next is built on the open-source Orca slicer[1] | Marlin[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch capacitive touchscreen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus slicer, Anycubic app and USB (print only); AI spaghetti detection and object skip supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Printer UI, slicing software, Anycubic app and USB drive (print only)[1] | USB serial; 16 GB flash drive included for standalone printing[2] |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, TPU (TPU is not compatible with the ACE Pro)[1] | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | 60 dB or less in standard mode - a manufacturer figure with no distance or method stated; markedly higher than the 46-48 dB Anycubic claims for the Kobra S1 and Kobra 4[1][7][8] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[9] | 1 year standard with extended options. Made in the USA[2] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Anycubic Kobra 3 Max product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- Anycubic Kobra 3 Max Shopify product JSON (variant prices and store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 2 Max store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 3 Combo product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- Anycubic Kobra S1 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 4 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor