3D Printing InfoPrinter comparison
Anycubic Kobra 2 Pro vs Bambu Lab P2S
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Anycubic Kobra 2 Pro comparisonsMore Bambu Lab P2S comparisons
| Property | Anycubic Kobra 2 ProBEDSLINGER | Bambu Lab P2SCOREXY |
|---|---|---|
| Identity | ||
| Brand | Anycubic | Bambu Lab |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Anycubic Kobra 2 Pro[1] | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[2] |
| Release date (announcement and actual shipping) | Listed on the Anycubic store from 2 February 2026 (Shopify publish date for this listing; the model itself is older)[1] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on store.anycubic.com, Aug 2026, with the compare-at price also $309.00[1] | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[3][4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Same 220 x 220 x 250 mm build volume as the Kobra 2 and Kobra 2 Neo, but Anycubic's own comparison table puts it at 500 mm/s max and 300 mm/s typical against the Kobra 2's 300/200 - the build volume alone will not tell these three apart. It also adds Anycubic APP support, which the base Kobra 2 lacks[1][5][6] | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[2][7] |
| Market position: superseded? successor announced? | Not documented | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 250 x 220 x 220 mm stated HWD, i.e. 220 x 220 x 250 mm; 12.1 L[1] | 256 x 256 x 256 mm (manufacturer figure)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 486 x 435 x 463 mm stated HWD - footprint about 435 x 463 mm[1] | 392 x 406 x 478 mm[2] |
| Net weight (kg) | 8.4 kg[1] | 14.9 kg net[2] |
| Frame construction & material | Not documented | Plastic and steel chassis with a plastic and glass outer frame[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bed-slinger[1] | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[2][4] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s maximum print speed (Anycubic Lab figure)[1] | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[2] |
| Recommended/typical print speed | 300 mm/s typical print speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | Not documented | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[2] |
| Max volumetric flow claimed (mm³/s) | Not documented | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[2] |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | One-click vibration compensation that detects X/Y resonance frequencies, plus flow control with retraction and refill compensation[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Optimised direct extruder[1] | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 260 C nozzle temperature ceiling; 0.4 mm replaceable nozzle[1] | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 110 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Anycubic LeviQ 2.0 automatic levelling with smart Z-offset[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Not documented | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[2] |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Cortex-A7 1.2 GHz application processor[1] | Not documented |
| Total rated power draw | Not documented | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[8] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | Not documented | 5-inch 854x480 touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Supports the Anycubic app (firmware 3.0.5 or later) for online model search, real-time video supervision, online slicing and remote control[1] | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Not documented | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[2][7] |
| Materials Support | ||
| Officially supported filament list | PLA, ABS, PETG, TPU (Kobra 2 family list)[5] | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[9] | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[10] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Anycubic Kobra 2 Pro store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- Anycubic Kobra 2 store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 2 Plus store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor