3D Printing InfoPrinter comparison
3DGence INDUSTRY F350 vs LulzBot TAZ Pro Long Bed
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore 3DGence INDUSTRY F350 comparisonsMore LulzBot TAZ Pro Long Bed comparisons
| Property | 3DGence INDUSTRY F350INDUSTRIAL | LulzBot TAZ Pro Long BedBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | 3DGence | LulzBot |
| Class | INDUSTRIAL | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | 3DGence INDUSTRY F350[1] | LulzBot TAZ Pro Long Bed 3D Printer[2] |
| Release date (announcement and actual shipping) | 2021[1] | Not documented |
| Launch MSRP (USD) | From $30,000 (Aniwaa quotes the same figure in EUR)[1] | Not documented |
| Street price (USD; dated snapshot per entry) | Not documented | $7,995.00 at MatterHackers, listed as currently unavailable, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Part of 3DGence's INDUSTRY line; Aniwaa's page covers only the F350. No live retail listing with a USD price was found, so the $30,000 figure is a starting price, not a street price[1] | Not simply a longer TAZ Pro. The Long Bed ships the Asteroid 285 tool head with a 1.2 mm nozzle, a 0.3-0.9 mm equipped layer range, an 80 °C bed cap (vs 110 °C), 150 mm/s travel (vs 300) and BLTouch 32-point mesh levelling (vs 4-point contact). Bed material also differs: blue spring-steel magnetic flex rather than glass with PEI film[2][3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 40.46 L (340 x 340 x 350 mm)[1] | 282 x 582 x 285 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 1825 x 960 x 940 mm[1] | Not documented |
| Net weight (kg) | 335 kg[1] | Not documented |
| Frame construction & material | Not documented | Open frame; GT2 belt drive with Igus SST rods and polymer bushings[2] |
| Enclosure: open / enclosed; panel material; door/lid | Enclosed with a heated chamber[1] | Open frame, no enclosure[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | 140 °C maximum chamber temperature (manufacturer specification, actively heated)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Two extruders; kinematic layout not stated on the source checked[1] | Cartesian bedslinger[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic TMC2130[2] |
| Speed & Acceleration | ||
| Max travel speed | Not documented | 150 mm/s maximum travel speed, firmware-limited[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Two extruders[1] | Asteroid 285 tool head[2] |
| Filament diameter | Not documented | 2.85 mm standard, 1.75 mm optional[2] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | 500 °C maximum nozzle temperature (manufacturer specification)[1] | 290 °C maximum, firmware-limited[2] |
| Stock nozzle size & sizes included in box | Not documented | 1.2 mm GammaMaster steel[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | GammaMaster steel[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 160 °C maximum bed temperature[1] | 80 °C maximum bed temperature — notably lower than the base TAZ Pro[2] |
| Bed heater type (DC/AC mains) & wattage | Not documented | 360 W, 24 V silicone bed heater[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Blue spring-steel magnetic flex bed system[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | BLTouch, 32-point automatic mesh calibration[2] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 32 points[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament sensor with runout and stripping detection[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Marlin[2] |
| Connectivity, UI & Camera | ||
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Not documented | USB serial; 16 GB flash drive included for standalone printing[2] |
| Materials Support | ||
| Officially supported filament list | PLA, ABS, ASA, PET, PA6, PA-CF, PEEK and various composites[1] | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 1 year standard with extended options. Made in the USA[2] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- 3DGence INDUSTRY F350 specification page aniwaa.com · 2026-08 · doc
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor