3D Printing Info

Filament comparison

PLA vs PPS

Compare printing settings, strength, heat resistance, dated prices and sources.

PLA (standard) guidePPS guide

2 selected · all documented properties

Open these two in the interactive comparisonMore PLA comparisonsMore PPS comparisons
PLA vs PPS — documented properties and sources
PropertyPLA (standard)PLAPPSHIGHTEMP
Market snapshot
Listing priceUSD/kg; dated snapshots$19.74/kg median; $9.99–$32.99/kg across 24 dated product listings$116.97/kg median; $84.00–$200.00/kg across 3 dated product listings
Identity & Market
Base polymer / chemistryPoly(lactic acid), a thermoplastic aliphatic polyester from fermented plant starch[1][2]Polyphenylene sulfide — a semi-crystalline high-temperature polymer[3][4]
Densityg/cm³1.17–1.24 (ISO 1183)[1][5][2]1.28 (ISO 1183, 3DXTech) and 1.33 (ISO 1183, Spectrum PPS AM230)[3][6]
Typical priceUSD/kgMainstream 1 kg spools cluster near 20[7][8][9]1 kg-equivalent spools span 84–200; the middle of the market is about 117[10][11][12]
Price range across brandsUSD/kg10–33 across brands; budget house brands 10–14, premium European 26–33[13][14][15][16]84-200 across brands and diameters; IEMAI 3D 84 at 1 kg, Spectrum PPS AM230 117 at 750 g, 3DXTech ThermaX PPS 140 at 2.85 mm and 200 at 1.75 mm[10][11][12]
Market availability1–5Ubiquitous, every brand and retailer[17][18]Niche, a handful of specialist brands[10][11]
Spool sizes & diameters1.75 and 2.85 mm; 0.75, 0.85, 1 and 1.1 kg spools plus spool-less refills[7][19][20][15][21]1.75 and 2.85 mm; 500 g and 750 g spools[10][11]
Typical applicationsConcept models, functional prototypes, low-wear toys, jigs used at room temperature[22]Chemical-plant and under-bonnet parts needing solvent resistance above 200 °C[4]
Diameter tolerance± mm±0.02 (Prusament) to ±0.03 (Bambu Lab, Prusa Research standard)[1][7][23]Not documented
Printing Parameters
Nozzle temperature°C190–230; Prusament specifies 210 ± 10[1][5][2]335-345 (3DXTech printed-specimen conditions); 300-330 (Spectrum)[3][6]
Bed temperature°C25–60; Prusament 40–60, Bambu Lab 35–45[1][5][2]110-130 (3DXTech); 100-120 (Spectrum)[3][6]
Enclosure / chamber requirement1–5Open frame is fine[5][17]Actively heated chamber required[24][25]
Recommended chamber temperature°CNot documented60-80 actively heated (Spectrum PPS AM230)[6]
Part cooling fan100 % from the second layer; reduce on the first one or two layers for bed adhesion[1][18]Not documented
Bed surface & adhesion aidSmooth or textured PEI, glass or painter's tape; glue stick only where release is a problem[5][26][18]Adhesive required — Spectrum specifies Magigoo Pro HT[6]
Maximum volumetric flow (mm³/s; see test conditions)mm³/s12–20 (PrusaSlicer max volumetric speed guidance for PLA)[27]Not documented
Warping tendency1–5None[28][17]Not documented
Bed-adhesion difficulty1–5Sticks to anything — glue only needed on smooth PEI[5][2][18]Not documented
Stringing / oozing tendency1–5Slight — 1–3 mm retraction handles it; oozing rises with nozzle temperature[5][18][29]Not documented
Overall printing difficulty1–5Beginner — prints on any machine out of the box[17][18]Expert / industrial hardware only[24][25]
Extruder requirementAny extruder; Bowden and direct drive both fine, no hardware upgrades[17]Not documented
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[17]Brass fine indefinitely for unfilled grades, but brass softens near these nozzle temperatures — hardened or plated hot ends are the norm[24]
Abrasiveness1–5Non-abrasive[28][17]Non-abrasive when unfilled[3]
Nozzle clog risk1–5Very low[17][18]Moderate — needs dry filament and a clean nozzle; 3DXTech lists no special nozzle concerns but a mandatory 110 °C pre-dry before every print[30]
Heat-creep / jam sensitivity1–5Moderate — good heatbreak cooling needed; softens below 60 °C so it deforms in a warm cold zone[26][31]Not documented
Hotend requirementAny standard hotend; PTFE-lined is fine at PLA temperatures[17]Not documented
Other hardware wearNone — brass nozzles and standard drive gears are unaffected[28][17]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.40–0.51 % saturated at 23–25 °C and 55–70 % RH[2][5][32]Negligible (<0.1 % EMC) — Polymaker states minimal water absorption at 0.05 %[4]
Equilibrium moisture content at ~50 % RH%0.43 saturated at 25 °C / 55 % RH (Bambu Lab); 0.51 equilibrium (Polymaker)[2][5]0.01 in 24 h on extruded stock (ASTM D570) — effectively non-absorbing[33]
Drying temperature & time50–55 °C for 6–8 h in a forced-air dryer; 45 °C for 12 h in the Bambu Lab AMS HT[5][2][31]At least 3 h at 90 °C in hot dry air if the filament has taken up moisture (Spectrum)[6]
Symptoms when wetBubbling and popping at the nozzle, stringing, rough surface and weak layers[34]Not documented
Effect of moisture on strengthPolymaker rates PLA low-sensitivity — it absorbs moisture slowly and the loss shows as poor layer adhesion and brittle layers rather than a published strength figure[34]Little to measure — equilibrium uptake is 0.05 %; 3DXTech still specifies a 110 °C, 4 h pre-dry before printing[4][30]
Storage requirementSealed with desiccant below 20 % RH; shelf life at ambient is long[2][18]Not documented
Mechanical Properties
Tensile strength (XY)MPa35–52 (printed XY, ISO 527); 55 mean across 16 brands and 53 for the reference PLA in a later run, both on 4×4 mm printed bars[1][5][2][35][36]50 at break (printed XY, ISO 527, 3DXTech); 65 at break injection-moulded (ISO 527, Spectrum); 94 at yield on extruded stock (ASTM D638)[3][6][33]
Young's modulusMPa2300–3427 (printed XY, ISO 527)[1][5][2]2650 (printed XY, ISO 527, 3DXTech); 3650 injection-moulded (ISO 527, Spectrum); 5769 on extruded stock (ASTM D638)[3][6][33]
Elongation at break%6.3–12.2 (printed XY, ISO 527); Prusament quotes 2.9 at yield[5][2][1]18 at break (printed XY, ISO 527, 3DXTech) against 2.0 injection-moulded (Spectrum) and 2.5 on extruded stock — the suppliers disagree by nearly an order of magnitude[3][6][33]
Flexural strengthMPa76–87 (printed XY, ISO 178); Fiberlogy quotes 81 by ASTM D790[1][5][2][37]52 (printed XY, ISO 178, 3DXTech); 141 on extruded stock (ASTM D790)[3][33]
Flexural modulusMPa2750–3230 (printed XY, ISO 178); Fiberlogy quotes 3800 by ASTM D790[1][5][2][37]2540 (printed XY, ISO 178)[3]
Charpy impact, notchedkJ/m²3.3–7.9 (printed XY, ISO 179, notched)[5][2]1.3 notched injection-moulded (ISO 179-1eA, Spectrum); unnotched 18[6]
Other impact dataCharpy unnotched, printed: 13–14 (Prusament, ISO 179-1), 26.6 (Bambu Lab PLA Basic)[1][2]Izod notched 33 J/m on extruded PPS stock, converted from 0.62 ft-lb/in (ASTM D256)[33]
Layer adhesion / Z tensileMPa17–31 (Prusa interlayer test and printed Z tensile); 23 mean on My Tech Fun 4×4 mm bars[1][2][36]Not documented
Brittleness1–5Brittle — snaps with little warning[26][28]Moderate[3]
Hardness (scale-specific)Shore A / Shore D / Rockwell81 Shore D (Prusa Polymers in-house method); 75.3 Shore D measured on printed bars (My Tech Fun, Sunlu PLA)[1][38]Rockwell 105 (and R124) on extruded PPS stock (ASTM D785)[33]
Creep resistance / sustained load1–5Poor — deforms under load at room temperature; 12 mm bar sagged to 20.3 mm over 5 days at 1.25 kg[39][40]Excellent — holds load for years. Ensinger lists high creep resistance as a headline property of extruded PPS stock, and Spectrum states that rigidity, strength and creep resistance are unchanged under continuous load at high temperature[33][6]
Fatigue / repeated-flex resistance1–5Poor — 38 000–49 000 cycles at 30 % of tensile strength, against 79 000–193 000 for PETG (printed, R = 0.2, 7 Hz)[41][26]Not documented
Elasticity / flexibility1–5Rigid[28]Rigid[3]
Z strength as % of XY%77–89 on TDS specimens; ≈44 on My Tech Fun 4×4 mm bars[5][2][36]Not documented
Thermal Properties
HDT at 0.45 MPa°C55–60 (ISO 75, 0.45 MPa)[1][5][2]90 (printed XY, ISO 75 at 0.45 MPa, 3DXTech); 129 injection-moulded (ISO 75, Spectrum); 204 on extruded stock (ASTM D648 at 66 psi)[3][6][33]
HDT at 1.8 MPa°C54–58 (ISO 75, 1.8 MPa)[1][5][2]107 injection-moulded (ISO 75 at 1.81 MPa, Spectrum); 104 on extruded stock (ASTM D648 at 264 psi)[6][33]
Glass transition (Tg)°C55–61 (DSC)[1][5][2]Not documented
Melting point / Vicat°C145–160 peak melt (Prusament, ISO 11357); 150 and 160 by DSC (PolyLite, Bambu Lab); Vicat 57–63 (ISO 306)[22][5][2]283 melting (ISO 11357, 3DXTech) and 280 on extruded stock; Vicat softening 236 at 50 N injection-moulded (ISO 306, Spectrum)[3][6][33]
Continuous service temperature°C50–55 — loaded bars begin to move at this temperature[28][36]170 long-term service on extruded PPS stock, converted from 338 °F[33]
Annealing responseBambu Lab conditions specimens at 55 °C for 8 h; annealing at 50–60 °C for 6–12 h raises crystallinity but can warp parts[2][42]Not documented
Thermal expansion (CTE)µm/m·K96 ± 5 at 0° and 99 ± 5 at 90° raster (printed PLA, fibre Bragg grating, 25–50 °C)[43]59.4 (extruded PPS stock, 22-60 °C, ASTM D696; source states 3.3e-5 in/in/°F)[33]
Flammability / UL 94Flammable; no UL 94 rating published by the major brands[2][5]UL 94 V-0 at 1.5 mm, rated on the base resin[3]
Environment & Chemical
UV resistance1–5Degrades within weeks outdoors[26][22]Not documented
Outdoor durabilityNot suitable for long-term outdoor use — UV embrittlement plus softening above 55 °C in direct sun[22][26]Not documented
Chemical resistanceGood against weak acids, oils and grease; poor against strong acids and alkalis; dissolved by chloroform, THF and hot benzene[5][26]Outstanding — PPS resists essentially all solvents below 200 °C[4]
Water / humidity resistance in service1–5Good — insoluble in water, absorbs 0.4–0.5 % at equilibrium[2][44]Excellent — essentially unaffected; extruded stock takes up 0.01 % water in 24 h[33]
Food contactBase resin is food-contact grade and EN 71-3 certified by some brands, but printed layer grooves harbour bacteria; Prusa advises against food use[26][44]Not documented
Biodegradability / compostabilityIndustrially compostable only — needs sustained 55 °C and specific microbial conditions; not home compostable[44][26][2]Not documented
RecyclabilityMechanically recyclable; not accepted in household plastic collection, so brand take-back schemes are the practical route[44]Not documented
Health & Safety
Fume toxicity1–5Low hazard — minimal VOC and particle emission[45]Moderate — measurable VOCs and UFPs, ventilation advised. None of these polymers was in the chamber study, and all are processed far above the temperatures it covered[45]
VOC emission rateµg/min4–5 lactide, the dominant VOC (chamber study, three printers)[45]Not documented
Ultrafine-particle emission rateparticles/min≈1 × 10⁸ median across three printers; only laywood ≈8 × 10⁷ and laybrick ≈6 × 10⁷ were lower[45]Not documented
Hazardous species emittedLactide (3,6-dimethyl-1,4-dioxane-2,5-dione) dominates; no styrene or caprolactam as a leading species[45]Not documented
Ventilation / filtration requirement1–5None needed in a normal room[45]Ventilated room or enclosure recommended[45]
Post-Processing
Sanding & machiningWet sanding — dry sanding heats the surface by friction and smears it[22][26]Not documented
Gluing & solvent weldingCyanoacrylate for most joints; some grades partially dissolve and bond with acetone, depending on additives and colour[26][23]Not documented
Vapour / chemical smoothingNo practical vapour smoothing — only chloroform, hot benzene or THF, which are laboratory-only[26]Not documented
Support material pairingPolySupport and PolyDissolve S1 (Polymaker); Support for PLA (Bambu Lab)[5][2]Not documented
Dimensional accuracy & detailGood — low shrinkage and features under 0.2 mm resolve; 55° overhangs and 30 mm bridges[28][2][18]Not documented
Solvents & Solubility
Soluble inChloroform: 10 % w/v in 2–4 h at 23 °C, every grade and morphology; THF and DMF only at 65 °C. Laboratory reagents.[46]None — PPS does not dissolve in any known solvent below 200 °C.[47][48]
Softened or crazed byAcetone, ethyl acetate and toluene plasticise it but dissolve <1 % even at 65 °C; submersion in acetone crazes and destroys parts.[46][49]Nothing at 23 °C; Ensinger rates it only conditionally resistant to benzene, dichloromethane, toluene and pyridine.[48]
Solvent welding & smoothing agentChloroform vapour smooths and welds PLA at the cost of tensile strength; acetone does not smooth it at all.[50][49]None — no solvent welds or smooths PPS.[47]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Prusament PLA Technical Datasheet v1.1 Prusa Polymers · 2022-02 · tds
  2. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  3. ThermaX PPS Technical Data Sheet v3 3DXTech · 2026-08 · tds
  4. PPS — material basics Polymaker Wiki · 2026-08 · doc
  5. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  6. Spectrum PPS AM230 Technical Data Sheet Spectrum Filaments · 2022-04 · tds
  7. PLA Basic — product page Bambu Lab US Store · 2026-08 · vendor
  8. MH Build Series PLA Filament White 1.75mm 1kg MatterHackers · 2026-08 · vendor
  9. 3DJAKE ecoPLA Black 1.75mm 1000g 3DJake International · 2026-08 · vendor
  10. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  11. Spectrum PPS AM230 Natural, 1.75 mm / 750 g 3DJAKE · 2026-08 · vendor
  12. IEMAI 3D PPS 3D Printing Filament — store page IEMAI 3D · 2026-08 · vendor
  13. JAYO PLA Classic 1.1KG 1.75mm JAYO Official Store · 2026-08 · vendor
  14. ELEGOO PLA Filament 1.75mm Colored 1KG Elegoo US Official Store · 2026-08 · vendor
  15. Fillamentum PLA Extrafill Natural 1kg Fillamentum USA · 2026-08 · vendor
  16. Prusament PLA Jet Black 1kg (NFC) Prusa Research · 2026-08 · vendor
  17. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  18. PLA — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  19. Fiberlogy rPLA Refill Anthracite 850 g 3DJake International · 2026-08 · vendor
  20. JAYO Silk PLA+ 1.75mm 1.1kg JAYO Official Store · 2026-08 · vendor
  21. ColorFabb PLA/PHA 750g 3D Universe · 2026-08 · vendor
  22. Prusament PLA Technical Data Sheet v1.0 Prusa Polymers · 2018-09 · tds
  23. Prusament rPLA Corn Pigment 1kg — product page Prusa Research · 2026-08 · vendor
  24. Prusament PEI 1010 Technical Datasheet v1.0 Prusa Polymers · 2024-09 · tds
  25. Prusament PEI 1010 — material page Prusa Polymers · 2026-08 · doc
  26. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  27. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  28. Prusament PLA — material page Prusa Polymers · 2026-08 · doc
  29. PLA — material basics Polymaker Wiki · 2026-08 · doc
  30. THERMAX PPS — product page (print recommendations) 3DXTech · 2026-08 · doc
  31. Filament Drying Recommendations Bambu Lab Wiki · 2026-08 · doc
  32. PolySonic PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  33. TECATRON natural (PPS) — stock shape properties Ensinger · 2026-08 · tds
  34. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  35. 16 PLA brand comparison test — results spreadsheet My Tech Fun (Igor Gaspar) · 2022-10 · test
  36. Creality Hyper PLA filament review — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  37. Easy PLA — product and technical data Fiberlogy · 2026-08 · tds
  38. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  39. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  40. PolyTerra PLA vs PLA+ — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  41. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  42. Bambu Filament Technical Data Sheet V3.0 — PLA Matte Bambu Lab · 2026-08 · tds
  43. Characterization of Thermal Expansion Coefficient of 3D Printing Polymeric Materials Using Fiber Bragg Grating Sensors Materials 17(18):4668 · 2024-09 · paper
  44. Filamentive PLA (recycled) — product page Filamentive · 2026-08 · vendor
  45. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  46. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  47. PPS (Polyphenylene sulfide) — Knowledge Base Prusa Research · 2026-08 · doc
  48. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  49. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  50. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper