3D Printing Info

Filament comparison

LW-PLA vs PEBA

Compare printing settings, strength, heat resistance, dated prices and sources.

Lightweight / foaming PLA (LW-PLA) guidePEBA (polyether block amide) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore LW-PLA comparisonsMore PEBA comparisons
LW-PLA vs PEBA — documented properties and sources
PropertyLightweight / foaming PLA (LW-PLA)PLAPEBA (polyether block amide)FLEX
Market snapshot
Listing priceUSD/kg; dated snapshots$47.48/kg median; $37.49–$50.00/kg across 4 dated product listings$60.99/kg median; $60.99–$60.99/kg across 1 dated product listings
Identity & Market
Base polymer / chemistryPLA with a blowing agent. Two distinct types: active-foaming grades that expand at the nozzle (Bambu Lab PLA Aero, colorFabb LW-PLA) and pre-foamed grades that do not (Polymaker PolyLite LW-PLA, PolyWood)[1][2][3][4]Polyether block amide: rigid polyamide and flexible polyether blocks.[5]
Densityg/cm³Filament 1.21 (Bambu Lab) and 1.24 (colorFabb); pre-foamed filament 0.8 (PolyWood, at 21.5 °C) and 0.9 (Polymaker LW-PLA); foamed prints reach 0.40[1][2][3][4]1.01 g/cm³ (GB/T 1033; eSUN manufacturer data)[5]
Typical priceUSD/kg1 kg-equivalent spools cluster near 45[6][2][7]Not documented
Price range across brandsUSD/kg37–50 across brands; Polymaker LW-PLA 37, Bambu Lab Aero 45, colorFabb 50, PolyWood 50[7][6][2]Not documented
Market availability1–5Available from several mainstream brands[6][7][2]Not documented
Spool sizes & diameters1.75 and 2.85 mm; 0.6, 0.75, 0.8 and 1 kg spools[7][2]1.75 mm diameter, 1 kg spool.[8]
Typical applicationsRC aircraft, drone airframes and large props where mass matters more than strength[1][2]Manufacturer applications include footwear, sports equipment and cushioning.[5]
Printing Parameters
Nozzle temperature°C210–260 (Bambu Lab, foaming); 195–260 (colorFabb, foaming); 190–210 (Polymaker, pre-foamed)[1][2][3]230–260 °C; 240 °C recommended.[5]
Bed temperature°C35–45 (Bambu Lab); 50–60 (colorFabb); 25–60 (Polymaker)[1][2][3]60–90 °C[5]
Enclosure / chamber requirement1–5Open frame is fine[3]Not documented
Part cooling fanFan on[1][3]10–50% fan recommended; mechanical-test specimens used 50–100%.[5]
Bed surface & adhesion aidNot documentedPEI build plate[5]
Maximum volumetric flow (mm³/s; see test conditions)mm³/s3.2–8 at the 40–100 mm/s colorFabb specifies and the 50–100 mm/s Polymaker specifies, on a 0.4 mm nozzle at 0.2 mm layer[3][2][9]9 mm³/s maximum in eSUN spiral-vase test; mechanical specimens used 2 mm³/s. Linear recommendation 25–110 mm/s is a separate quantity.[5]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; flow has to be cut to match the expansion[2]Not documented
Extruder requirementBambu Lab PLA Aero is 0.4 mm nozzle only on the store and wiki, while its own TDS lists 0.4, 0.6 and 0.8[1][10]Not documented
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[3][4]Not documented
Abrasiveness1–5Non-abrasive[3][4]Not documented
Nozzle clog risk1–5High — jams from moisture, heat creep or particles; Bambu Lab warns the foamed extrudate swells and easily clogs the nozzle, and rules out 0.2 mm nozzles[10]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.45 % saturated at 25 °C / 55 % RH (Bambu Lab); 0.40 % equilibrium (Polymaker)[1][3]Not documented
Equilibrium moisture content at ~50 % RH%0.45 saturated at 25 °C / 55 % RH (Bambu Lab); 0.40 equilibrium (Polymaker)[1][3]Not documented
Drying temperature & time55 °C for 6–8 h[1][3]70–75 °C for 6–8 h; re-dry after receiving or extended exposure.[5]
Effect of moisture on strengthPolymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures for this grade; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[11]Not documented
Mechanical Properties
Tensile strength (XY)MPa24 ± 2 (Bambu Lab) and 24.4 (Polymaker) printed XY, ISO 527; colorFabb falls from 43.1 unfoamed to 10.8 at 45 % flow[1][3][2]>16.5 MPa printed XY, GB/T 1040; manufacturer lower bound, not an exact measurement.[5]
Young's modulusMPa1350 ± 250 (Bambu Lab) and 1689 (Polymaker) printed XY, ISO 527; colorFabb falls from 3334 unfoamed to 864 foamed[1][3][2]Not documented
Elongation at break%2.6 ± 0.7 (Bambu Lab) and 8.8 (Polymaker) printed XY, ISO 527[1][3]>520% printed XY, GB/T 1040; manufacturer lower bound.[5]
Flexural strengthMPa45 ± 4 (Bambu Lab) and 50.2 (Polymaker) printed XY, ISO 178[1][3]Not documented
Flexural modulusMPa1690 ± 120 (Bambu Lab) and 1959 (Polymaker) printed XY, ISO 178[1][3]Not documented
Charpy impact, notchedkJ/m²8.2 ± 0.7 printed XY, ISO 179, notched (Bambu Lab); colorFabb 3.67 foamed[1][2]Not documented
Other impact dataCharpy unnotched 28.8 printed XY (Bambu Lab); colorFabb 5.46 foamed[1][2]Not documented
Layer adhesion / Z tensileMPa18 ± 3 printed Z, ISO 527 (Bambu Lab); flexural Z collapses to 17 against 45 in XY[1]7.5 MPa printed Z, GB/T 1040 (manufacturer test)[5]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2.6 % in XY and 1.2 % in Z[1]Not documented
Hardness (scale-specific)Shore A / Shore D / RockwellNot documented90 Shore A nominal grade designation; do not compare numerically with Shore D or Rockwell.[8]
Creep resistance / sustained load1–5Poor — no foamed-grade creep test; plain printed PLA sagged from 12 to 16.2–21.8 mm over 5 days at 1.25 kg, and the foam carries less solid[12][13][14]Not documented
Fatigue / repeated-flex resistance1–5Poor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength and elongation at break falls to 2.6 % in XY and 1.2 % in Z[15][1]Not documented
Elasticity / flexibility1–5Rigid[1]Not documented
Z strength as % of XY%75 by tensile, 38 by flexural (printed, Bambu Lab)[1]Not documented
Thermal Properties
HDT at 0.45 MPa°C53 (Bambu Lab) and 54 (Polymaker), ISO 75 at 0.45 MPa[1][3]Not documented
HDT at 1.8 MPa°C48 (Bambu Lab) and 50 (Polymaker), ISO 75 at 1.8 MPa[1][3]Not documented
Glass transition (Tg)°C55 (Bambu Lab) and 59 (Polymaker), DSC[1][3]Not documented
Melting point / Vicat°C150 peak melt (Polymaker, DSC); Vicat 60 °C[3]110 °C Vicat softening (GB/T 1633, 120 °C/h, 10 N); not HDT or a continuous-use rating.[5]
Annealing responseBambu Lab advises against annealing thin, low-infill Aero prints[1]Not documented
Environment & Chemical
UV resistance1–5Degrades within weeks outdoors[16]Not documented
Health & Safety
Fume toxicity1–5Low hazard — minimal VOC and particle emission[17]Not documented
Ventilation / filtration requirement1–5None needed in a normal room[17]Not documented
Post-Processing
Dimensional accuracy & detailFoamed surfaces are rough and matte; dimensional accuracy depends on holding the foaming temperature steady[1][2]Not documented
Solvents & Solubility
Soluble inChloroform dissolves the PLA matrix; the foamed wall wicks solvent right through instead of only skinning over.[18]Not documented
Softened or crazed byAcetone, ethyl acetate and toluene plasticise the matrix but dissolve <1 % even at 65 °C; acetone submersion crazes parts.[18][19]Not documented
Solvent welding & smoothing agentChloroform vapour reaches only the resin skin; no workshop-safe smoothing agent exists for PLA of any kind.[20][19]Not documented

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Bambu Filament Technical Data Sheet V4.0 — PLA Aero Bambu Lab · 2026-08 · tds
  2. LW-PLA technical data sheet colorFabb · 2026-08 · tds
  3. PolyLite LW-PLA Technical Data Sheet (V7.0) Polymaker · 2026-08 · tds
  4. PolyWood Technical Data Sheet Version 4.0 (Nov 2018) Polymaker (copy hosted by 3Dee) · 2018-11 · tds
  5. eSUN PEBA-90A Technical Data Sheet v1.0 (Aug 2025), checked 2026-10-17 eSUN · 2025-08 · tds
  6. PLA Aero — product page Bambu Lab US Store · 2026-08 · vendor
  7. Polymaker product catalogue Polymaker · 2026-08 · vendor
  8. eSUN PEBA-90A official product page: 1 kg price and product identity eSUN · 2026-10-17 · vendor
  9. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  10. PLA Usage Guide Bambu Lab Wiki · 2026-08 · doc
  11. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  12. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  13. Polymaker PLA Pro vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  14. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  15. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  16. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  17. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  18. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  19. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  20. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper