3D Printing Info

Filament comparison

Conductive vs PPS

Compare printing settings, strength, heat resistance, dated prices and sources.

Conductive filament guidePPS guide

2 selected · all documented properties

Open these two in the interactive comparisonMore Conductive comparisonsMore PPS comparisons
Conductive vs PPS — documented properties and sources
PropertyConductive filamentSPECIALTYPPSHIGHTEMP
Market snapshot
Listing priceUSD/kg; dated snapshots$170.36/kg median; $89.99–$796.00/kg across 4 dated product listings$116.97/kg median; $84.00–$200.00/kg across 3 dated product listings
Identity & Market
Base polymer / chemistryA carbon-filled compound conductive by volume rather than merely dissipative; Proto-pasta's is PLA-based, Recreus's and NinjaTek's are TPU, and add:north's Koltron G1 does not state its base polymer[1][2][3][4]Polyphenylene sulfide — a semi-crystalline high-temperature polymer[5][6]
Densityg/cm³Not documented1.28 (ISO 1183, 3DXTech) and 1.33 (ISO 1183, Spectrum PPS AM230)[5][7]
Typical priceUSD/kg1 kg-equivalent spools span 90–181 for the carbon-filled grades; add:north's Koltron G1 sits far above at 796 because it is sold only in 100 and 250 g coils[8][9][10]1 kg-equivalent spools span 84–200; the middle of the market is about 117[11][12][13]
Price range across brandsUSD/kg90–796 across brands; Proto-pasta conductive PLA 90 at 1 kg, Recreus Conductive Filaflex 160 at 500 g, NinjaTek Eel 181 at 1 kg, add:north Koltron G1 796 at 250 g[8][2][9][10]84-200 across brands and diameters; IEMAI 3D 84 at 1 kg, Spectrum PPS AM230 117 at 750 g, 3DXTech ThermaX PPS 140 at 2.85 mm and 200 at 1.75 mm[11][12][13]
Market availability1–5Niche, a handful of specialist brands[8][2]Niche, a handful of specialist brands[11][12]
Spool sizes & diameters1.75 and 2.85 mm; 0.05, 0.1, 0.25, 0.5, 1 and 2 kg spools[8][2][9][10]1.75 and 2.85 mm; 500 g and 750 g spools[11][12]
Typical applicationsCapacitive touch surfaces, low-current traces, EMI shielding and static-safe fixtures[1]Chemical-plant and under-bonnet parts needing solvent resistance above 200 °C[6]
Printing Parameters
Nozzle temperature°CNot documented335-345 (3DXTech printed-specimen conditions); 300-330 (Spectrum)[5][7]
Bed temperature°CNot documented110-130 (3DXTech); 100-120 (Spectrum)[5][7]
Enclosure / chamber requirement1–5Open frame is fine[1]Actively heated chamber required[14][15]
Recommended chamber temperature°CNot documented60-80 actively heated (Spectrum PPS AM230)[7]
Bed surface & adhesion aidNot documentedAdhesive required — Spectrum specifies Magigoo Pro HT[7]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile[1]Expert / industrial hardware only[14][15]
Hardware Wear & Reliability
Nozzle hardness required1–4Brass acceptable; hardened steel for volume work[1]Brass fine indefinitely for unfilled grades, but brass softens near these nozzle temperatures — hardened or plated hot ends are the norm[14]
Abrasiveness1–5Moderately abrasive — conductive carbon filler[1]Non-abrasive when unfilled[5]
Nozzle clog risk1–5Low — Proto-pasta states the carbon-filled grade prints on standard PLA settings with no special nozzle required[1]Moderate — needs dry filament and a clean nozzle; 3DXTech lists no special nozzle concerns but a mandatory 110 °C pre-dry before every print[16]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Not documentedNegligible (<0.1 % EMC) — Polymaker states minimal water absorption at 0.05 %[6]
Equilibrium moisture content at ~50 % RH%Not documented0.01 in 24 h on extruded stock (ASTM D570) — effectively non-absorbing[17]
Drying temperature & timeNot documentedAt least 3 h at 90 °C in hot dry air if the filament has taken up moisture (Spectrum)[7]
Effect of moisture on strengthPolymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[18]Little to measure — equilibrium uptake is 0.05 %; 3DXTech still specifies a 110 °C, 4 h pre-dry before printing[6][16]
Mechanical Properties
Tensile strength (XY)MPaNot documented50 at break (printed XY, ISO 527, 3DXTech); 65 at break injection-moulded (ISO 527, Spectrum); 94 at yield on extruded stock (ASTM D638)[5][7][17]
Young's modulusMPaNot documented2650 (printed XY, ISO 527, 3DXTech); 3650 injection-moulded (ISO 527, Spectrum); 5769 on extruded stock (ASTM D638)[5][7][17]
Elongation at break%Not documented18 at break (printed XY, ISO 527, 3DXTech) against 2.0 injection-moulded (Spectrum) and 2.5 on extruded stock — the suppliers disagree by nearly an order of magnitude[5][7][17]
Flexural strengthMPaNot documented52 (printed XY, ISO 178, 3DXTech); 141 on extruded stock (ASTM D790)[5][17]
Flexural modulusMPaNot documented2540 (printed XY, ISO 178)[5]
Charpy impact, notchedkJ/m²Not documented1.3 notched injection-moulded (ISO 179-1eA, Spectrum); unnotched 18[7]
Other impact dataNot documentedIzod notched 33 J/m on extruded PPS stock, converted from 0.62 ft-lb/in (ASTM D256)[17]
Brittleness1–5Brittle — snaps with little warning; carbon-black loading at conductive levels embrittles PLA[1]Moderate[5]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documentedRockwell 105 (and R124) on extruded PPS stock (ASTM D785)[17]
Creep resistance / sustained load1–5Not documentedExcellent — holds load for years. Ensinger lists high creep resistance as a headline property of extruded PPS stock, and Spectrum states that rigidity, strength and creep resistance are unchanged under continuous load at high temperature[17][7]
Elasticity / flexibility1–5Rigid[1]Rigid[5]
Thermal Properties
HDT at 0.45 MPa°CNot documented90 (printed XY, ISO 75 at 0.45 MPa, 3DXTech); 129 injection-moulded (ISO 75, Spectrum); 204 on extruded stock (ASTM D648 at 66 psi)[5][7][17]
HDT at 1.8 MPa°CNot documented107 injection-moulded (ISO 75 at 1.81 MPa, Spectrum); 104 on extruded stock (ASTM D648 at 264 psi)[7][17]
Melting point / Vicat°CNot documented283 melting (ISO 11357, 3DXTech) and 280 on extruded stock; Vicat softening 236 at 50 N injection-moulded (ISO 306, Spectrum)[5][7][17]
Continuous service temperature°CNot documented170 long-term service on extruded PPS stock, converted from 338 °F[17]
Thermal expansion (CTE)µm/m·KNot documented59.4 (extruded PPS stock, 22-60 °C, ASTM D696; source states 3.3e-5 in/in/°F)[17]
Flammability / UL 94Not documentedUL 94 V-0 at 1.5 mm, rated on the base resin[5]
Environment & Chemical
Chemical resistanceNot documentedOutstanding — PPS resists essentially all solvents below 200 °C[6]
Water / humidity resistance in service1–5Not documentedExcellent — essentially unaffected; extruded stock takes up 0.01 % water in 24 h[17]
Electrical & ESD propertiesConductive rather than dissipative — Proto-pasta sells the grade as electrically conductive composite PLA[1]Not documented
Health & Safety
Fume toxicity1–5Low hazard — minimal VOC and particle emission; none of these materials was in the chamber study[19]Moderate — measurable VOCs and UFPs, ventilation advised. None of these polymers was in the chamber study, and all are processed far above the temperatures it covered[19]
Ventilation / filtration requirement1–5Open a window / occasional ventilation[19]Ventilated room or enclosure recommended[19]
Dust & fibre handling hazardConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[1]Not documented
Solvents & Solubility
Soluble inChloroform dissolves PLA-based grades, leaving the carbon black; TPU-based grades need DMF, NMP or THF. Laboratory reagents.[20][21]None — PPS does not dissolve in any known solvent below 200 °C.[22][23]
Softened or crazed byAcetone and ethyl acetate plasticise a PLA-based grade; a TPU-based grade swells in toluene, esters and alcohols.[20][21]Nothing at 23 °C; Ensinger rates it only conditionally resistant to benzene, dichloromethane, toluene and pyridine.[23]
Solvent welding & smoothing agentNone — neither PLA nor TPU has a workshop-safe welding or smoothing solvent.[20][21]None — no solvent welds or smooths PPS.[22]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Electrically Conductive Composite PLA — product page and technical data Proto-pasta · 2026-08 · tds
  2. Recreus product catalogue Recreus · 2026-08 · vendor
  3. Eel 3D Printing Filament Technical Specifications NinjaTek · 2026-08 · tds
  4. Koltron G1 Technical Data Sheet add:north · 2026-08 · tds
  5. ThermaX PPS Technical Data Sheet v3 3DXTech · 2026-08 · tds
  6. PPS — material basics Polymaker Wiki · 2026-08 · doc
  7. Spectrum PPS AM230 Technical Data Sheet Spectrum Filaments · 2022-04 · tds
  8. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  9. Eel product page — durometer, print guidelines and price NinjaTek · 2026-08 · vendor
  10. add:north Koltron G1 product page add:north · 2026-08 · vendor
  11. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  12. Spectrum PPS AM230 Natural, 1.75 mm / 750 g 3DJAKE · 2026-08 · vendor
  13. IEMAI 3D PPS 3D Printing Filament — store page IEMAI 3D · 2026-08 · vendor
  14. Prusament PEI 1010 Technical Datasheet v1.0 Prusa Polymers · 2024-09 · tds
  15. Prusament PEI 1010 — material page Prusa Polymers · 2026-08 · doc
  16. THERMAX PPS — product page (print recommendations) 3DXTech · 2026-08 · doc
  17. TECATRON natural (PPS) — stock shape properties Ensinger · 2026-08 · tds
  18. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  19. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  20. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  21. Elastollan — Chemical properties: swelling and chemical resistance BASF · 2026-08 · tds
  22. PPS (Polyphenylene sulfide) — Knowledge Base Prusa Research · 2026-08 · doc
  23. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds