3D Printing Info

Filament comparison

ASA-GF vs PEBA

Compare printing settings, strength, heat resistance, dated prices and sources.

Glass-fibre ASA (ASA-GF) guidePEBA (polyether block amide) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ASA-GF comparisonsMore PEBA comparisons
ASA-GF vs PEBA — documented properties and sources
PropertyGlass-fibre ASA (ASA-GF)ASAPEBA (polyether block amide)FLEX
Market snapshot
Listing priceUSD/kg; dated snapshots$29.95/kg median; $26.99–$33.99/kg across 3 dated product listings$60.99/kg median; $60.99–$60.99/kg across 1 dated product listings
Identity & Market
Base polymer / chemistryASA reinforced with chopped glass fibre — 10 wt% (Spectrum ASA-X GF10), 15 wt% (ZYLtech ASA-GF)[1][2]Polyether block amide: rigid polyamide and flexible polyether blocks.[3]
Densityg/cm³1.07 (ZYLtech) and 1.11 (Spectrum), ISO 1183[1][2]1.01 g/cm³ (GB/T 1033; eSUN manufacturer data)[3]
Typical priceUSD/kg1 kg spools cluster near 28[4][5]Not documented
Price range across brandsUSD/kg27–34 across brands; Ambrosia 27, ZYLtech 30, Siraya Tech 34[4][5][6]Not documented
Market availability1–5Niche, a handful of specialist brands[4][1][2]Not documented
Spool sizes & diameters1.75 and 2.85 mm; 1 kg spools[2][4]1.75 mm diameter, 1 kg spool.[7]
Typical applicationsOutdoor brackets and mounts that need stiffness and dimensional stability under sun and moisture[1][2]Manufacturer applications include footwear, sports equipment and cushioning.[3]
Diameter tolerance± mm±0.01 at 95 % probability and ±0.02 at 100 % (ZYLtech)[2]Not documented
Printing Parameters
Nozzle temperature°C240–270 (Spectrum); 240–280 (ZYLtech)[1][2]230–260 °C; 240 °C recommended.[3]
Bed temperature°C80–100 (Spectrum); 90–110 on PEI (ZYLtech)[1][2]60–90 °C[3]
Enclosure / chamber requirement1–5Enclosure recommended[8]Not documented
Part cooling fan0–20 % (Spectrum)[1]10–50% fan recommended; mechanical-test specimens used 50–100%.[3]
Bed surface & adhesion aidPEI sheet, BuildTak or an adhesion aid such as Magigoo (Polymaker); Simplify3D also lists Kapton tape and ASA slurry[9][10]PEI build plate[3]
Maximum volumetric flow (mm³/s; see test conditions)mm³/s2.4–5.6 at Spectrum's 30–70 mm/s on a 0.4 mm nozzle at 0.2 mm layer; ZYLtech allows up to 200 mm/s[1][2][11]9 mm³/s maximum in eSUN spiral-vase test; mechanical specimens used 2 mm³/s. Linear recommendation 25–110 mm/s is a separate quantity.[3]
Warping tendency1–5Moderate — needs adhesion aid or draught shield[8]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[9]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[9]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; ZYLtech requires a hardened nozzle of 0.6 mm or larger[2][1]Not documented
Extruder requirementZYLtech specifies a hardened nozzle 0.6 mm or larger; Spectrum bases its settings on a 0.5 mm nozzle[2][1]Not documented
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required — Spectrum recommends ruby or hardened, ZYLtech requires hardened[1][2]Not documented
Abrasiveness1–5Highly abrasive — standard GF composite[1][2]Not documented
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; Prusa lists higher risk of nozzle clogging for glass-filled composites[12]Not documented
Heat-creep / jam sensitivity1–5Slightly sensitive[10]Not documented
Hotend requirementNo special hotend required[10]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ASA matrix takes up 0.40–0.45 % saturated at 25 °C / 55 % RH; no glass-filled grade publishes its own figure[13][14][15]Not documented
Drying temperature & timeNot documented70–75 °C for 6–8 h; re-dry after receiving or extended exposure.[3]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[16]Not documented
Effect of moisture on strengthNo dry-versus-conditioned figures are published; Polymaker groups the styrenics as moderate-sensitivity and absorbed water shows as bubbling and poor layer adhesion[16]Not documented
Storage requirementSealed with desiccant; Polymaker rates the styrenics moderate-sensitivity[16]Not documented
Mechanical Properties
Tensile strength (XY)MPa33–36 at break, ISO 527 (ZYLtech; specimen type not stated); Spectrum quotes 55 at break on injection-moulded specimens[2][1]>16.5 MPa printed XY, GB/T 1040; manufacturer lower bound, not an exact measurement.[3]
Young's modulusMPa2540–2890 (ZYLtech; specimen type not stated) and 2550 (Spectrum, injection-moulded), ISO 527[2][1]Not documented
Elongation at break%3.4 at break (ZYLtech; specimen type not stated); Spectrum quotes 2.80 at yield on injection-moulded specimens[2][1]>520% printed XY, GB/T 1040; manufacturer lower bound.[3]
Flexural modulusMPa2130–2480 flexural modulus, ISO 178 (ZYLtech; specimen type not stated)[2]Not documented
Charpy impact, notchedkJ/m²8.3 notched Charpy at 23 °C on injection-moulded specimens (Spectrum, ISO 179-1eA); ZYLtech publishes notched Izod 6.9 by ISO 180 instead[1][2]Not documented
Other impact dataCharpy unnotched 25 kJ/m² at 23 °C on injection-moulded specimens (Spectrum, ISO 179-1eU); ZYLtech notched Izod 6.9 kJ/m² (ISO 180)[1][2]Not documented
Layer adhesion / Z tensileMPaNot documented7.5 MPa printed Z, GB/T 1040 (manufacturer test)[3]
Brittleness1–5Brittle — snaps with little warning; elongation at break 3.4 %[2]Not documented
Hardness (scale-specific)Shore A / Shore D / RockwellNot documented90 Shore A nominal grade designation; do not compare numerically with Shore D or Rockwell.[7]
Creep resistance / sustained load1–5Good — no creep test found; chopped glass fibre lifts modulus to 2540–2890 against 2379–2450 for unfilled ASA[2][14][13]Not documented
Fatigue / repeated-flex resistance1–5Below average — no GF-grade S-N curve; elongation at break falls to 3.4 % against 6.7–9.2 % for unfilled ASA[2][14][13]Not documented
Elasticity / flexibility1–5Rigid[2]Not documented
Thermal Properties
HDT at 0.45 MPa°C100 (Spectrum, injection-moulded, ISO 75 at 0.45 MPa)[1]Not documented
HDT at 1.8 MPa°C97–99 unannealed (ZYLtech, ISO 75 at 1.8 MPa; specimen type not stated); Spectrum 90 on injection-moulded specimens[2][1]Not documented
Melting point / Vicat°CAmorphous ASA matrix; Vicat 98 (Spectrum, ISO 306). ZYLtech quotes a 210–220 °C melting range by ISO 11357 for its grade[1][2]110 °C Vicat softening (GB/T 1633, 120 °C/h, 10 N); not HDT or a continuous-use rating.[3]
Continuous service temperature°C93 — Prusa publishes this as the temperature resistance of Prusament ASA[17]Not documented
Flammability / UL 94Flammable; no UL 94 rating published[13]Not documented
Environment & Chemical
UV resistance1–5Excellent — designed for permanent outdoor use; Spectrum states the parts resist prolonged UV and moisture exposure[1][18]Not documented
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[14]Not documented
Food contactNot food safe[9]Not documented
Biodegradability / compostabilityNot biodegradable[9]Not documented
RecyclabilityNot accepted in household plastic collection[9]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[19][8]Not documented
Hazardous species emittedStyrene. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea. Azimi et al. measured styrene from every styrenic filament tested but did not test ASA itself[8][19]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration[19][8]Not documented
Dust & fibre handling hazardGlass fibre is bound in the matrix; avoid inhaling sanding dust[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[9]Not documented
Painting & finishingPaints readily; ASA holds colour outdoors so many parts are left unpainted[9]Not documented
Gluing & solvent weldingSolvent-welds with acetone[14]Not documented
Vapour / chemical smoothingAcetone vapour smoothing works[14]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a Support for ABS that also serves ASA[8]Not documented
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre; MEK, THF, ethyl acetate and chlorinated solvents attack the styrenic backbone.[20][14]Not documented
Softened or crazed byLimonene attacks some grades — Prusa reports Prusament ASA Orange flaking apart as layer adhesion fails.[21]Not documented
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[22][14]Not documented

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Spectrum ASA-X GF10 Technical Data Sheet (mechanical and thermal data marked injection-moulded) Spectrum Filaments · 2026-08 · tds
  2. ZYLtech ASA-GF Filament Technical Data Sheet v1 ZYLtech · 2026-08 · tds
  3. eSUN PEBA-90A Technical Data Sheet v1.0 (Aug 2025), checked 2026-10-17 eSUN · 2025-08 · tds
  4. Filastruder product catalogue Filastruder · 2026-08 · vendor
  5. ZYLtech ASA-GF Glass Fiber filament — product page ZYLtech · 2026-08 · vendor
  6. Siraya Tech Fibreheart ASA-GF Filament product page Siraya Tech · 2026-08 · vendor
  7. eSUN PEBA-90A official product page: 1 kg price and product identity eSUN · 2026-10-17 · vendor
  8. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  9. ASA — material basics Polymaker Wiki · 2026-08 · doc
  10. ASA — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  11. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  12. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  13. Bambu Filament Technical Data Sheet V3.0 — ASA Bambu Lab · 2026-08 · tds
  14. PolyLite ASA Technical Data Sheet Polymaker · 2024-11 · tds
  15. Prusament ASA Technical Datasheet v1.1 Prusa Polymers · 2024-05 · tds
  16. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  17. Prusament ASA — material page Prusa Polymers · 2026-08 · doc
  18. ASA — FDM Material Data Sheet (includes 1000 h QUV exposure results) Stratasys · 2026-08 · tds
  19. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  20. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  21. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  22. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc