3D Printing Info

Filament comparison

ABS+ vs PLA

Compare printing settings, strength, heat resistance, dated prices and sources.

ABS+ / Tough ABS guidePLA (standard) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS+ comparisonsMore PLA comparisons
ABS+ vs PLA — documented properties and sources
PropertyABS+ / Tough ABSABSPLA (standard)PLA
Market snapshot
Listing priceUSD/kg; dated snapshots$26.49/kg median; $15.99–$29.99/kg across 4 dated product listings$19.74/kg median; $9.99–$32.99/kg across 24 dated product listings
Identity & Market
Base polymer / chemistryABS reformulated for lower warping and a higher glass transition; Polymaker's ABS Pro and ABS Max reach Tg 114.9 and 126.3 °C against 101 °C for PolyLite ABS[1][2][3]Poly(lactic acid), a thermoplastic aliphatic polyester from fermented plant starch[4][5]
Densityg/cm³1.04 (ABS Pro) and 1.06 (ABS Max), ISO 1183[1][2]1.17–1.24 (ISO 1183)[4][6][5]
Typical priceUSD/kg1 kg spools cluster near 27[7]Mainstream 1 kg spools cluster near 20[8][9][10]
Price range across brandsUSD/kg16–30 across brands; SUNLU E-ABS 16, Polymaker ABS Pro 25, YXPOLYER ABS Enhanced 28, Polymaker ABS Max 30[7][11][12]10–33 across brands; budget house brands 10–14, premium European 26–33[13][14][15][16]
Market availability1–5Available from several mainstream brands[7]Ubiquitous, every brand and retailer[17][18]
Spool sizes & diameters1.75 and 2.85 mm; 1 kg spools[7]1.75 and 2.85 mm; 0.75, 0.85, 1 and 1.1 kg spools plus spool-less refills[8][19][20][15][21]
Typical applicationsLarge enclosure and automotive parts where plain ABS warps or softens too early[1][2]Concept models, functional prototypes, low-wear toys, jigs used at room temperature[22]
Diameter tolerance± mmNot documented±0.02 (Prusament) to ±0.03 (Bambu Lab, Prusa Research standard)[4][8][23]
Printing Parameters
Nozzle temperature°C270–290 (ABS Pro); 270–300 (ABS Max) — 25–35 °C above plain ABS[1][2]190–230; Prusament specifies 210 ± 10[4][6][5]
Bed temperature°C120 (ABS Max)[2]25–60; Prusament 40–60, Bambu Lab 35–45[4][6][5]
Enclosure / chamber requirement1–5Enclosure required (passive)[1][2][24]Open frame is fine[6][17]
Part cooling fanNot documented100 % from the second layer; reduce on the first one or two layers for bed adhesion[4][18]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[24][25]Smooth or textured PEI, glass or painter's tape; glue stick only where release is a problem[6][26][18]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sUp to 250 mm/s (ABS Pro) and 200 mm/s (ABS Max), equivalent to 20 and 16 on a 0.4 mm nozzle at 0.2 mm layer[1][2][27]12–20 (PrusaSlicer max volumetric speed guidance for PLA)[27]
Warping tendency1–5High — enclosure needed for reliable large parts[24]None[28][17]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[24]Sticks to anything — glue only needed on smooth PEI[6][5][18]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[29]Slight — 1–3 mm retraction handles it; oozing rises with nozzle temperature[6][18][30]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; the hotter nozzle rules out PTFE-lined hotends[1][2]Beginner — prints on any machine out of the box[17][18]
Extruder requirementNot documentedAny extruder; Bowden and direct drive both fine, no hardware upgrades[17]
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[24]Brass fine indefinitely[17]
Abrasiveness1–5Non-abrasive[24]Non-abrasive[28][17]
Nozzle clog risk1–5Low — unfilled ABS compound; no special hot-end required and clogging is not among the listed drawbacks[25][17]Very low[17][18]
Heat-creep / jam sensitivity1–5Slightly sensitive[25]Moderate — good heatbreak cooling needed; softens below 60 °C so it deforms in a warm cold zone[26][31]
Hotend requirementNo special hot-end required[25]Any standard hotend; PTFE-lined is fine at PLA temperatures[17]
Other hardware wearNot documentedNone — brass nozzles and standard drive gears are unaffected[28][17]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.51 % maximum water absorption (ABS Pro)[1]Moderate — 0.40–0.51 % saturated at 23–25 °C and 55–70 % RH[5][6][32]
Equilibrium moisture content at ~50 % RH%0.51 maximum water absorption (Polymaker ABS Pro)[1]0.43 saturated at 25 °C / 55 % RH (Bambu Lab); 0.51 equilibrium (Polymaker)[5][6]
Drying temperature & time70 °C for 6 h (ABS Max)[2]50–55 °C for 6–8 h in a forced-air dryer; 45 °C for 12 h in the Bambu Lab AMS HT[6][5][31]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[33]Bubbling and popping at the nozzle, stringing, rough surface and weak layers[33]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures[33]Polymaker rates PLA low-sensitivity — it absorbs moisture slowly and the loss shows as poor layer adhesion and brittle layers rather than a published strength figure[33]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[33]Sealed with desiccant below 20 % RH; shelf life at ambient is long[5][18]
Mechanical Properties
Tensile strength (XY)MPa34.9 (ABS Pro) and 35.7 (ABS Max) printed XY, ISO 527[1][2]35–52 (printed XY, ISO 527); 55 mean across 16 brands and 53 for the reference PLA in a later run, both on 4×4 mm printed bars[4][6][5][34][35]
Young's modulusMPa2330 (ABS Pro) and 2320 (ABS Max) printed XY, ISO 527[1][2]2300–3427 (printed XY, ISO 527)[4][6][5]
Elongation at break%6.7 (ABS Max) and 7.3 (ABS Pro) at break, printed XY, ISO 527[1][2]6.3–12.2 (printed XY, ISO 527); Prusament quotes 2.9 at yield[6][5][4]
Flexural strengthMPa60.1 (ABS Pro) and 63.3 (ABS Max) printed XY, ISO 178[1][2]76–87 (printed XY, ISO 178); Fiberlogy quotes 81 by ASTM D790[4][6][5][36]
Flexural modulusMPa2330 (ABS Pro) and 2500 (ABS Max) printed XY, ISO 178[1][2]2750–3230 (printed XY, ISO 178); Fiberlogy quotes 3800 by ASTM D790[4][6][5][36]
Charpy impact, notchedkJ/m²10.5 (ABS Max) and 14.5 (ABS Pro) printed XY, ISO 179, notched[1][2]3.3–7.9 (printed XY, ISO 179, notched)[6][5]
Other impact dataNot documentedCharpy unnotched, printed: 13–14 (Prusament, ISO 179-1), 26.6 (Bambu Lab PLA Basic)[4][5]
Layer adhesion / Z tensileMPa21.9 (ABS Pro) and 25.4 (ABS Max) printed Z, ISO 527[1][2]17–31 (Prusa interlayer test and printed Z tensile); 23 mean on My Tech Fun 4×4 mm bars[4][5][35]
Brittleness1–5Tough — absorbs impact, yields before breaking[1][2]Brittle — snaps with little warning[26][28]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documented81 Shore D (Prusa Polymers in-house method); 75.3 Shore D measured on printed bars (My Tech Fun, Sunlu PLA)[4][37]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 115 °C (ABS Pro) and 126 °C (ABS Max) keeps room-temperature service far below softening[1][2]Poor — deforms under load at room temperature; 12 mm bar sagged to 20.3 mm over 5 days at 1.25 kg[38][39]
Fatigue / repeated-flex resistance1–5Moderate — no S-N curve found; 6.7–7.3 % elongation and 10.5–14.5 kJ/m² notched Charpy, below unfilled Bambu Lab ABS[1][2][40]Poor — 38 000–49 000 cycles at 30 % of tensile strength, against 79 000–193 000 for PETG (printed, R = 0.2, 7 Hz)[41][26]
Elasticity / flexibility1–5Rigid[1]Rigid[28]
Z strength as % of XY%63 (ABS Pro) and 71 (ABS Max), printed[1][2]77–89 on TDS specimens; ≈44 on My Tech Fun 4×4 mm bars[6][5][35]
Thermal Properties
HDT at 0.45 MPa°C106.4 (ABS Pro) and 118.1 (ABS Max), ISO 75 at 0.45 MPa[1][2]55–60 (ISO 75, 0.45 MPa)[4][6][5]
HDT at 1.8 MPa°C101.4 (ABS Pro) and 113.1 (ABS Max), ISO 75 at 1.8 MPa[1][2]54–58 (ISO 75, 1.8 MPa)[4][6][5]
Glass transition (Tg)°C114.9 (ABS Pro) and 126.3 (ABS Max), DSC[1][2]55–61 (DSC)[4][6][5]
Melting point / Vicat°CAmorphous — no melting point; Vicat 116.1 (ABS Pro) and 127.4 (ABS Max), ISO 306[1][2]145–160 peak melt (Prusament, ISO 11357); 150 and 160 by DSC (PolyLite, Bambu Lab); Vicat 57–63 (ISO 306)[22][6][5]
Continuous service temperature°CNot documented50–55 — loaded bars begin to move at this temperature[28][35]
Annealing responseNot documentedBambu Lab conditions specimens at 55 °C for 8 h; annealing at 50–60 °C for 6–12 h raises crystallinity but can warp parts[5][42]
Thermal expansion (CTE)µm/m·K86–89 for printed unfilled ABS (fibre Bragg grating, 25–50 °C); no grade-specific measurement published[43]96 ± 5 at 0° and 99 ± 5 at 90° raster (printed PLA, fibre Bragg grating, 25–50 °C)[43]
Flammability / UL 94Not documentedFlammable; no UL 94 rating published by the major brands[5][6]
Environment & Chemical
UV resistance1–5Months outdoors before embrittlement[29]Degrades within weeks outdoors[26][22]
Outdoor durabilityNot documentedNot suitable for long-term outdoor use — UV embrittlement plus softening above 55 °C in direct sun[22][26]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[3]Good against weak acids, oils and grease; poor against strong acids and alkalis; dissolved by chloroform, THF and hot benzene[6][26]
Water / humidity resistance in service1–5Not documentedGood — insoluble in water, absorbs 0.4–0.5 % at equilibrium[5][44]
Food contactNot food safe — Polymaker cites potential chemical leaching[29]Base resin is food-contact grade and EN 71-3 certified by some brands, but printed layer grooves harbour bacteria; Prusa advises against food use[26][44]
Biodegradability / compostabilityNot biodegradable[29]Industrially compostable only — needs sustained 55 °C and specific microbial conditions; not home compostable[44][26][5]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[29]Mechanically recyclable; not accepted in household plastic collection, so brand take-back schemes are the practical route[44]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[45][24]Low hazard — minimal VOC and particle emission[45]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[45]4–5 lactide, the dominant VOC (chamber study, three printers)[45]
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[45]≈1 × 10⁸ median across three printers; only laywood ≈8 × 10⁷ and laybrick ≈6 × 10⁷ were lower[45]
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[45][24]Lactide (3,6-dimethyl-1,4-dioxane-2,5-dione) dominates; no styrene or caprolactam as a leading species[45]
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[45][24]None needed in a normal room[45]
Post-Processing
Sanding & machiningSands well and takes filler before painting[29]Wet sanding — dry sanding heats the surface by friction and smears it[22][26]
Painting & finishingPaints readily after light abrasion[29]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate for most joints; some grades partially dissolve and bond with acetone, depending on additives and colour[26][23]
Vapour / chemical smoothingAcetone vapour smoothing works[3]No practical vapour smoothing — only chloroform, hot benzene or THF, which are laboratory-only[26]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[46][24]PolySupport and PolyDissolve S1 (Polymaker); Support for PLA (Bambu Lab)[6][5]
Dimensional accuracy & detailNot documentedGood — low shrinkage and features under 0.2 mm resolve; 55° overhangs and 30 mm bridges[28][5][18]
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[47][3]Chloroform: 10 % w/v in 2–4 h at 23 °C, every grade and morphology; THF and DMF only at 65 °C. Laboratory reagents.[48]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[47][49]Acetone, ethyl acetate and toluene plasticise it but dissolve <1 % even at 65 °C; submersion in acetone crazes and destroys parts.[48][50]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[50]Chloroform vapour smooths and welds PLA at the cost of tensile strength; acetone does not smooth it at all.[51][50]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  2. Polymaker ABS Max Technical Data Sheet V1.1 (2026-06-01) Polymaker · 2026-06 · tds
  3. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  4. Prusament PLA Technical Datasheet v1.1 Prusa Polymers · 2022-02 · tds
  5. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  6. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  7. Polymaker product catalogue Polymaker · 2026-08 · vendor
  8. PLA Basic — product page Bambu Lab US Store · 2026-08 · vendor
  9. MH Build Series PLA Filament White 1.75mm 1kg MatterHackers · 2026-08 · vendor
  10. 3DJAKE ecoPLA Black 1.75mm 1000g 3DJake International · 2026-08 · vendor
  11. SUNLU E-ABS (Easy ABS) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  12. YXPOLYER ABS Enhanced product page YXPOLYER · 2026-08 · vendor
  13. JAYO PLA Classic 1.1KG 1.75mm JAYO Official Store · 2026-08 · vendor
  14. ELEGOO PLA Filament 1.75mm Colored 1KG Elegoo US Official Store · 2026-08 · vendor
  15. Fillamentum PLA Extrafill Natural 1kg Fillamentum USA · 2026-08 · vendor
  16. Prusament PLA Jet Black 1kg (NFC) Prusa Research · 2026-08 · vendor
  17. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  18. PLA — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  19. Fiberlogy rPLA Refill Anthracite 850 g 3DJake International · 2026-08 · vendor
  20. JAYO Silk PLA+ 1.75mm 1.1kg JAYO Official Store · 2026-08 · vendor
  21. ColorFabb PLA/PHA 750g 3D Universe · 2026-08 · vendor
  22. Prusament PLA Technical Data Sheet v1.0 Prusa Polymers · 2018-09 · tds
  23. Prusament rPLA Corn Pigment 1kg — product page Prusa Research · 2026-08 · vendor
  24. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  25. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  26. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  27. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  28. Prusament PLA — material page Prusa Polymers · 2026-08 · doc
  29. ABS — material basics Polymaker Wiki · 2026-08 · doc
  30. PLA — material basics Polymaker Wiki · 2026-08 · doc
  31. Filament Drying Recommendations Bambu Lab Wiki · 2026-08 · doc
  32. PolySonic PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  33. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  34. 16 PLA brand comparison test — results spreadsheet My Tech Fun (Igor Gaspar) · 2022-10 · test
  35. Creality Hyper PLA filament review — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  36. Easy PLA — product and technical data Fiberlogy · 2026-08 · tds
  37. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  38. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  39. PolyTerra PLA vs PLA+ — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  40. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  41. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  42. Bambu Filament Technical Data Sheet V3.0 — PLA Matte Bambu Lab · 2026-08 · tds
  43. Characterization of Thermal Expansion Coefficient of 3D Printing Polymeric Materials Using Fiber Bragg Grating Sensors Materials 17(18):4668 · 2024-09 · paper
  44. Filamentive PLA (recycled) — product page Filamentive · 2026-08 · vendor
  45. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  46. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  47. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  48. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  49. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  50. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  51. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper