3D Printing Info

Filament comparison

ABS+ vs PLA Matte

Compare printing settings, strength, heat resistance, dated prices and sources.

ABS+ / Tough ABS guideMatte PLA guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS+ comparisonsMore PLA Matte comparisons
ABS+ vs PLA Matte — documented properties and sources
PropertyABS+ / Tough ABSABSMatte PLAPLA
Market snapshot
Listing priceUSD/kg; dated snapshots$26.49/kg median; $15.99–$29.99/kg across 4 dated product listings$19.09/kg median; $10.99–$32.16/kg across 10 dated product listings
Identity & Market
Base polymer / chemistryABS reformulated for lower warping and a higher glass transition; Polymaker's ABS Pro and ABS Max reach Tg 114.9 and 126.3 °C against 101 °C for PolyLite ABS[1][2][3]PLA compounded with a mineral filler — Fiberlogy names chalk — that scatters light into a diffuse finish[4][5]
Densityg/cm³1.04 (ABS Pro) and 1.06 (ABS Max), ISO 1183[1][2]1.31 (Bambu Lab, ISO 1183) to 1.38 (Fiberlogy PLA Mineral, method not stated) — above plain PLA from the filler[5][4]
Typical priceUSD/kg1 kg spools cluster near 27[6]Mainstream 1 kg spools cluster near 21[7][8][9]
Price range across brandsUSD/kg16–30 across brands; SUNLU E-ABS 16, Polymaker ABS Pro 25, YXPOLYER ABS Enhanced 28, Polymaker ABS Max 30[6][10][11]11–32 across brands; budget house brands 11–19, Fiberlogy PLA Mineral 32[12][8][13]
Market availability1–5Available from several mainstream brands[6]Stocked by most mainstream brands[12][9][7]
Spool sizes & diameters1.75 and 2.85 mm; 1 kg spools[6]1.75 mm; 1 kg spools plus spool-less refills[7][14]
Typical applicationsLarge enclosure and automotive parts where plain ABS warps or softens too early[1][2]Display models and visible parts where a matte, non-reflective finish matters[5]
Diameter tolerance± mmNot documented±0.03 (Bambu Lab)[15]
Printing Parameters
Nozzle temperature°C270–290 (ABS Pro); 270–300 (ABS Max) — 25–35 °C above plain ABS[1][2]190–230 (Bambu Lab); 190–210 (Fiberlogy PLA Mineral)[5][4]
Bed temperature°C120 (ABS Max)[2]35–45 (Bambu Lab); 60 (Fiberlogy)[5][4]
Enclosure / chamber requirement1–5Enclosure required (passive)[1][2][16]Open frame is fine[5][4]
Part cooling fanNot documentedFan on; Fiberlogy specifies 75–100 %[5][4]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[16][17]Cool plate, high-temperature plate or textured PEI with glue (Bambu Lab); smooth PEI, textured PEI or glass (Fiberlogy)[5][4]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sUp to 250 mm/s (ABS Pro) and 200 mm/s (ABS Max), equivalent to 20 and 16 on a 0.4 mm nozzle at 0.2 mm layer[1][2][18]Not documented
Warping tendency1–5High — enclosure needed for reliable large parts[16]None[5]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[16]Sticks to anything[19]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[20]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; the hotter nozzle rules out PTFE-lined hotends[1][2]Beginner — prints on any machine out of the box[5][4]
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[16]Brass fine indefinitely[21][5][4]
Abrasiveness1–5Non-abrasive[16]Slightly abrasive — mineral filler pushes density from 1.24 to 1.31–1.38[4][5][22]
Nozzle clog risk1–5Low — unfilled ABS compound; no special hot-end required and clogging is not among the listed drawbacks[17][21]Very low[21]
Heat-creep / jam sensitivity1–5Slightly sensitive[17]Moderate — good heatbreak cooling needed; PLA softens below 60 °C[23]
Hotend requirementNo special hot-end required[17]No special hot-end required[19]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.51 % maximum water absorption (ABS Pro)[1]Moderate — 0.40 % saturated at 25 °C / 55 % RH[5]
Equilibrium moisture content at ~50 % RH%0.51 maximum water absorption (Polymaker ABS Pro)[1]0.40 saturated at 25 °C / 55 % RH (Bambu Lab)[5]
Drying temperature & time70 °C for 6 h (ABS Max)[2]50 °C for 8 h in a forced-air dryer, or 60–70 °C for 12 h on an X1 heatbed; Fiberlogy specifies 50 °C for 6 h[5][4][24]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[25]Bubbling and popping at the nozzle, stringing, rough surface and weak layers[25]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures[25]Polymaker rates PLA low-sensitivity — the loss shows as poor layer adhesion and brittle layers rather than a published strength figure[25]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[25]Sealed with desiccant below 20 % RH; shelf life at ambient is long[22][19]
Mechanical Properties
Tensile strength (XY)MPa34.9 (ABS Pro) and 35.7 (ABS Max) printed XY, ISO 527[1][2]30 (printed XY, ISO 527, Bambu Lab); 35.1 on My Tech Fun bars for PolyTerra PLA[5][26]
Young's modulusMPa2330 (ABS Pro) and 2320 (ABS Max) printed XY, ISO 527[1][2]1960 (Bambu Lab, printed XY, ISO 527); Fiberlogy PLA Mineral quotes 3500 (ISO 527, specimen type not stated)[5][4]
Elongation at break%6.7 (ABS Max) and 7.3 (ABS Pro) at break, printed XY, ISO 527[1][2]14.8 (printed XY, ISO 527)[5]
Flexural strengthMPa60.1 (ABS Pro) and 63.3 (ABS Max) printed XY, ISO 178[1][2]53 (printed XY, ISO 178) — 30 % below PLA Basic at 76[5][22]
Flexural modulusMPa2330 (ABS Pro) and 2500 (ABS Max) printed XY, ISO 178[1][2]2360 (printed XY, ISO 178)[5]
Charpy impact, notchedkJ/m²10.5 (ABS Max) and 14.5 (ABS Pro) printed XY, ISO 179, notched[1][2]6.3 (printed XY, ISO 179, notched); unnotched 19.2[5]
Other impact dataNot documentedIzod 6.1 kJ/m² on My Tech Fun printed bars for PolyTerra PLA[26]
Layer adhesion / Z tensileMPa21.9 (ABS Pro) and 25.4 (ABS Max) printed Z, ISO 527[1][2]22 (printed Z, ISO 527); flexural Z falls to 29 against 53 in XY; 12.9 on My Tech Fun layer-adhesion bars[5][26]
Brittleness1–5Tough — absorbs impact, yields before breaking[1][2]Brittle — snaps with little warning[5]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 115 °C (ABS Pro) and 126 °C (ABS Max) keeps room-temperature service far below softening[1][2]Poor — 12 mm bar sagged to 18.7 mm over 5 days at 1.25 kg[26]
Fatigue / repeated-flex resistance1–5Moderate — no S-N curve found; 6.7–7.3 % elongation and 10.5–14.5 kJ/m² notched Charpy, below unfilled Bambu Lab ABS[1][2][27]Poor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength (R = 0.2)[28][23]
Elasticity / flexibility1–5Rigid[1]Rigid[5]
Z strength as % of XY%63 (ABS Pro) and 71 (ABS Max), printed[1][2]73 by tensile, 55 by flexural (printed, Bambu Lab)[5]
Thermal Properties
HDT at 0.45 MPa°C106.4 (ABS Pro) and 118.1 (ABS Max), ISO 75 at 0.45 MPa[1][2]58 (Bambu Lab) and 48 (Fiberlogy PLA Mineral), ISO 75 at 0.45 MPa[5][4]
HDT at 1.8 MPa°C101.4 (ABS Pro) and 113.1 (ABS Max), ISO 75 at 1.8 MPa[1][2]52 (ISO 75, 1.8 MPa)[5]
Glass transition (Tg)°C114.9 (ABS Pro) and 126.3 (ABS Max), DSC[1][2]61 (DSC)[5]
Melting point / Vicat°CAmorphous — no melting point; Vicat 116.1 (ABS Pro) and 127.4 (ABS Max), ISO 306[1][2]163 peak melt (DSC); Vicat 63 °C[5]
Continuous service temperature°CNot documented54 — loaded bars begin to move at this temperature[26]
Annealing responseNot documented50–60 °C for 6–12 h; some prints deform or warp, and a forced-air oven is required[5]
Thermal expansion (CTE)µm/m·K86–89 for printed unfilled ABS (fibre Bragg grating, 25–50 °C); no grade-specific measurement published[29]Not documented
Flammability / UL 94Not documentedFlammable; no UL 94 rating published by the major brands[22][30]
Environment & Chemical
UV resistance1–5Months outdoors before embrittlement[20]Degrades within weeks outdoors[23][31]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[3]Good against weak acids, oils and grease; poor against strong acids and alkalis; dissolved by chloroform, THF and hot benzene[30][23]
Water / humidity resistance in service1–5Not documentedGood — insoluble in water[22]
Food contactNot food safe — Polymaker cites potential chemical leaching[20]Base resin is food-contact grade, but printed layer grooves harbour bacteria; Prusa advises against food use[23]
Biodegradability / compostabilityNot biodegradable[20]Industrially compostable only — needs sustained 55 °C; not home compostable[32][23]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[20]Mechanically recyclable; not accepted in household plastic collection[32]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[33][16]Low hazard — minimal VOC and particle emission[33]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[33]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[33]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[33][16]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[33][16]None needed in a normal room[33]
Post-Processing
Sanding & machiningSands well and takes filler before painting[20]Wet sanding — dry sanding heats the surface by friction and smears it[31][23]
Painting & finishingPaints readily after light abrasion[20]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate for most joints; some grades partially dissolve and bond with acetone[23][34]
Vapour / chemical smoothingAcetone vapour smoothing works[3]No practical vapour smoothing — only chloroform, hot benzene or THF, which are laboratory-only[23]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[35][16]Support for PLA (Bambu Lab)[5]
Dimensional accuracy & detailNot documentedMatte surface hides layer lines; 55° overhangs and 30 mm bridges as for plain PLA[5]
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[36][3]Chloroform: 10 % w/v in 2–4 h at 23 °C, every grade and morphology; THF and DMF only at 65 °C. Laboratory reagents.[37]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[36][38]Acetone, ethyl acetate and toluene plasticise it but dissolve <1 % even at 65 °C; submersion in acetone crazes and destroys parts.[37][39]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[39]Chloroform vapour smooths and welds PLA at the cost of tensile strength; acetone does not smooth it at all.[40][39]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  2. Polymaker ABS Max Technical Data Sheet V1.1 (2026-06-01) Polymaker · 2026-06 · tds
  3. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  4. PLA Mineral — product and technical data Fiberlogy · 2026-08 · tds
  5. Bambu Filament Technical Data Sheet V3.0 — PLA Matte Bambu Lab · 2026-08 · tds
  6. Polymaker product catalogue Polymaker · 2026-08 · vendor
  7. Polymaker Panchroma Matte PLA — product listing 3DJake International · 2026-08 · vendor
  8. Overture Matte PLA 1.75mm Overture3D · 2026-08 · vendor
  9. Matte PLA filament collection Anycubic Official Store · 2026-08 · vendor
  10. SUNLU E-ABS (Easy ABS) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  11. YXPOLYER ABS Enhanced product page YXPOLYER · 2026-08 · vendor
  12. Matte PLA filament collection Sunlu Official Store · 2026-08 · vendor
  13. Fiberlogy PLA Mineral — product listing 3DJake International · 2026-08 · vendor
  14. Extrudr PLA NX2 Matt — product listing 3DJake International · 2026-08 · vendor
  15. PLA Basic — product page Bambu Lab US Store · 2026-08 · vendor
  16. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  17. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  18. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  19. PLA — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  20. ABS — material basics Polymaker Wiki · 2026-08 · doc
  21. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  22. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  23. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  24. Filament Drying Recommendations Bambu Lab Wiki · 2026-08 · doc
  25. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  26. PolyTerra PLA vs PLA+ — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  27. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  28. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  29. Characterization of Thermal Expansion Coefficient of 3D Printing Polymeric Materials Using Fiber Bragg Grating Sensors Materials 17(18):4668 · 2024-09 · paper
  30. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  31. Prusament PLA Technical Data Sheet v1.0 Prusa Polymers · 2018-09 · tds
  32. Filamentive PLA (recycled) — product page Filamentive · 2026-08 · vendor
  33. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  34. Prusament rPLA Corn Pigment 1kg — product page Prusa Research · 2026-08 · vendor
  35. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  36. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  37. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  38. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  39. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  40. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper