3D Printing Info

Filament comparison

ABS+ vs Conductive

Compare printing settings, strength, heat resistance, dated prices and sources.

ABS+ / Tough ABS guideConductive filament guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS+ comparisonsMore Conductive comparisons
ABS+ vs Conductive — documented properties and sources
PropertyABS+ / Tough ABSABSConductive filamentSPECIALTY
Market snapshot
Listing priceUSD/kg; dated snapshots$26.49/kg median; $15.99–$29.99/kg across 4 dated product listings$170.36/kg median; $89.99–$796.00/kg across 4 dated product listings
Identity & Market
Base polymer / chemistryABS reformulated for lower warping and a higher glass transition; Polymaker's ABS Pro and ABS Max reach Tg 114.9 and 126.3 °C against 101 °C for PolyLite ABS[1][2][3]A carbon-filled compound conductive by volume rather than merely dissipative; Proto-pasta's is PLA-based, Recreus's and NinjaTek's are TPU, and add:north's Koltron G1 does not state its base polymer[4][5][6][7]
Densityg/cm³1.04 (ABS Pro) and 1.06 (ABS Max), ISO 1183[1][2]Not documented
Typical priceUSD/kg1 kg spools cluster near 27[8]1 kg-equivalent spools span 90–181 for the carbon-filled grades; add:north's Koltron G1 sits far above at 796 because it is sold only in 100 and 250 g coils[9][10][11]
Price range across brandsUSD/kg16–30 across brands; SUNLU E-ABS 16, Polymaker ABS Pro 25, YXPOLYER ABS Enhanced 28, Polymaker ABS Max 30[8][12][13]90–796 across brands; Proto-pasta conductive PLA 90 at 1 kg, Recreus Conductive Filaflex 160 at 500 g, NinjaTek Eel 181 at 1 kg, add:north Koltron G1 796 at 250 g[9][5][10][11]
Market availability1–5Available from several mainstream brands[8]Niche, a handful of specialist brands[9][5]
Spool sizes & diameters1.75 and 2.85 mm; 1 kg spools[8]1.75 and 2.85 mm; 0.05, 0.1, 0.25, 0.5, 1 and 2 kg spools[9][5][10][11]
Typical applicationsLarge enclosure and automotive parts where plain ABS warps or softens too early[1][2]Capacitive touch surfaces, low-current traces, EMI shielding and static-safe fixtures[4]
Printing Parameters
Nozzle temperature°C270–290 (ABS Pro); 270–300 (ABS Max) — 25–35 °C above plain ABS[1][2]Not documented
Bed temperature°C120 (ABS Max)[2]Not documented
Enclosure / chamber requirement1–5Enclosure required (passive)[1][2][14]Open frame is fine[4]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[14][15]Not documented
Maximum volumetric flow (mm³/s; see test conditions)mm³/sUp to 250 mm/s (ABS Pro) and 200 mm/s (ABS Max), equivalent to 20 and 16 on a 0.4 mm nozzle at 0.2 mm layer[1][2][16]Not documented
Warping tendency1–5High — enclosure needed for reliable large parts[14]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[14]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[17]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; the hotter nozzle rules out PTFE-lined hotends[1][2]Intermediate — dry filament and a tuned profile[4]
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[14]Brass acceptable; hardened steel for volume work[4]
Abrasiveness1–5Non-abrasive[14]Moderately abrasive — conductive carbon filler[4]
Nozzle clog risk1–5Low — unfilled ABS compound; no special hot-end required and clogging is not among the listed drawbacks[15][18]Low — Proto-pasta states the carbon-filled grade prints on standard PLA settings with no special nozzle required[4]
Heat-creep / jam sensitivity1–5Slightly sensitive[15]Not documented
Hotend requirementNo special hot-end required[15]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.51 % maximum water absorption (ABS Pro)[1]Not documented
Equilibrium moisture content at ~50 % RH%0.51 maximum water absorption (Polymaker ABS Pro)[1]Not documented
Drying temperature & time70 °C for 6 h (ABS Max)[2]Not documented
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[19]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures[19]Polymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[19]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[19]Not documented
Mechanical Properties
Tensile strength (XY)MPa34.9 (ABS Pro) and 35.7 (ABS Max) printed XY, ISO 527[1][2]Not documented
Young's modulusMPa2330 (ABS Pro) and 2320 (ABS Max) printed XY, ISO 527[1][2]Not documented
Elongation at break%6.7 (ABS Max) and 7.3 (ABS Pro) at break, printed XY, ISO 527[1][2]Not documented
Flexural strengthMPa60.1 (ABS Pro) and 63.3 (ABS Max) printed XY, ISO 178[1][2]Not documented
Flexural modulusMPa2330 (ABS Pro) and 2500 (ABS Max) printed XY, ISO 178[1][2]Not documented
Charpy impact, notchedkJ/m²10.5 (ABS Max) and 14.5 (ABS Pro) printed XY, ISO 179, notched[1][2]Not documented
Layer adhesion / Z tensileMPa21.9 (ABS Pro) and 25.4 (ABS Max) printed Z, ISO 527[1][2]Not documented
Brittleness1–5Tough — absorbs impact, yields before breaking[1][2]Brittle — snaps with little warning; carbon-black loading at conductive levels embrittles PLA[4]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 115 °C (ABS Pro) and 126 °C (ABS Max) keeps room-temperature service far below softening[1][2]Not documented
Fatigue / repeated-flex resistance1–5Moderate — no S-N curve found; 6.7–7.3 % elongation and 10.5–14.5 kJ/m² notched Charpy, below unfilled Bambu Lab ABS[1][2][20]Not documented
Elasticity / flexibility1–5Rigid[1]Rigid[4]
Z strength as % of XY%63 (ABS Pro) and 71 (ABS Max), printed[1][2]Not documented
Thermal Properties
HDT at 0.45 MPa°C106.4 (ABS Pro) and 118.1 (ABS Max), ISO 75 at 0.45 MPa[1][2]Not documented
HDT at 1.8 MPa°C101.4 (ABS Pro) and 113.1 (ABS Max), ISO 75 at 1.8 MPa[1][2]Not documented
Glass transition (Tg)°C114.9 (ABS Pro) and 126.3 (ABS Max), DSC[1][2]Not documented
Melting point / Vicat°CAmorphous — no melting point; Vicat 116.1 (ABS Pro) and 127.4 (ABS Max), ISO 306[1][2]Not documented
Thermal expansion (CTE)µm/m·K86–89 for printed unfilled ABS (fibre Bragg grating, 25–50 °C); no grade-specific measurement published[21]Not documented
Environment & Chemical
UV resistance1–5Months outdoors before embrittlement[17]Not documented
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[3]Not documented
Food contactNot food safe — Polymaker cites potential chemical leaching[17]Not documented
Biodegradability / compostabilityNot biodegradable[17]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[17]Not documented
Electrical & ESD propertiesNot documentedConductive rather than dissipative — Proto-pasta sells the grade as electrically conductive composite PLA[4]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[22][14]Low hazard — minimal VOC and particle emission; none of these materials was in the chamber study[22]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[22]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[22]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[22][14]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[22][14]Open a window / occasional ventilation[22]
Dust & fibre handling hazardNot documentedConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[4]
Post-Processing
Sanding & machiningSands well and takes filler before painting[17]Not documented
Painting & finishingPaints readily after light abrasion[17]Not documented
Vapour / chemical smoothingAcetone vapour smoothing works[3]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[23][14]Not documented
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[24][3]Chloroform dissolves PLA-based grades, leaving the carbon black; TPU-based grades need DMF, NMP or THF. Laboratory reagents.[25][26]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[24][27]Acetone and ethyl acetate plasticise a PLA-based grade; a TPU-based grade swells in toluene, esters and alcohols.[25][26]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[28]None — neither PLA nor TPU has a workshop-safe welding or smoothing solvent.[25][26]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  2. Polymaker ABS Max Technical Data Sheet V1.1 (2026-06-01) Polymaker · 2026-06 · tds
  3. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  4. Electrically Conductive Composite PLA — product page and technical data Proto-pasta · 2026-08 · tds
  5. Recreus product catalogue Recreus · 2026-08 · vendor
  6. Eel 3D Printing Filament Technical Specifications NinjaTek · 2026-08 · tds
  7. Koltron G1 Technical Data Sheet add:north · 2026-08 · tds
  8. Polymaker product catalogue Polymaker · 2026-08 · vendor
  9. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  10. Eel product page — durometer, print guidelines and price NinjaTek · 2026-08 · vendor
  11. add:north Koltron G1 product page add:north · 2026-08 · vendor
  12. SUNLU E-ABS (Easy ABS) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  13. YXPOLYER ABS Enhanced product page YXPOLYER · 2026-08 · vendor
  14. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  15. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  16. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  17. ABS — material basics Polymaker Wiki · 2026-08 · doc
  18. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  19. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  20. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  21. Characterization of Thermal Expansion Coefficient of 3D Printing Polymeric Materials Using Fiber Bragg Grating Sensors Materials 17(18):4668 · 2024-09 · paper
  22. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  23. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  24. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  25. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  26. Elastollan — Chemical properties: swelling and chemical resistance BASF · 2026-08 · tds
  27. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  28. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc