3D Printing Info

Filament comparison

ABS-FR vs PLA-GF

Compare printing settings, strength, heat resistance, dated prices and sources.

Flame-retardant ABS (FR-ABS) guideGlass-fibre PLA (PLA-GF) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-FR comparisonsMore PLA-GF comparisons
ABS-FR vs PLA-GF — documented properties and sources
PropertyFlame-retardant ABS (FR-ABS)ABSGlass-fibre PLA (PLA-GF)PLA
Market snapshot
Listing priceUSD/kg; dated snapshots$52.00/kg median; $44.99–$120.00/kg across 5 dated product listings$44.99/kg median; $29.99–$59.99/kg across 2 dated product listings
Identity & Market
Base polymer / chemistryABS with a flame-retardant package; 3DXTech rates the base resin UL 94 V-0[1]PLA filled with chopped glass fibre — 12 wt% (Polymaker HT-PLA-GF), 15–20 wt% (eSUN PLA-GF). Bambu Lab PLA Galaxy uses glass microspheres, not fibre, and is not equivalent[2][3][4]
Densityg/cm³1.18 (ISO 1183) — above unfilled ABS at 1.05 because of the retardant loading[1][5]1.31 (eSUN) to 1.337 (Polymaker), ISO 1183 / GB/T 1033[2][3]
Typical priceUSD/kg1 kg-equivalent spools span 45–120; the middle of the market is about 52[6][7][8][9]1 kg spools cluster near 30[10][11]
Price range across brandsUSD/kg45–120 across brands; SUNLU 45, YXPOLYER 50, Coex 3D 52, 3DXTech 107 at 750 g pricing; the FR PC/ABS grade runs 120[6][7][8][9]30–60 across brands; Polymaker 30, Proto-pasta 60[10][11]
Market availability1–5Niche, a handful of specialist brands[6]Niche, a handful of specialist brands[10][11][3]
Spool sizes & diameters1.75 and 2.85 mm; 750 g spools[6]1.75 mm; 0.5 and 1 kg spools[11][12]
Typical applicationsElectrical enclosures and transport interiors that must meet a flammability rating[1]Stiff brackets and fixtures; the Polymaker grade is aimed at parts annealed for heat resistance[2]
Printing Parameters
Nozzle temperature°CNot documented210–230 (Polymaker HT-PLA-GF)[2]
Bed temperature°CNot documented25–60 (Polymaker HT-PLA-GF)[2]
Enclosure / chamber requirement1–5Enclosure recommended[13]Open frame is fine[2]
Part cooling fanNot documentedFan on — eSUN specifies 100 %[3]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[13][14]Not documented
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documented28 at Polymaker's stated 350 mm/s on a 0.4 mm nozzle at 0.2 mm layer; eSUN prints its specimens at 60 mm/s[2][3][15]
Warping tendency1–5High — enclosure needed for reliable large parts[13]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[13]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[16]Not documented
Shrinkage%Not documented0.05 in X-Y and Z, 0.10 diagonal (Polymaker HT-PLA-GF)[2]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile[13]Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[2]
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[13]Hardened steel required[2]
Abrasiveness1–5Non-abrasive[1]Highly abrasive — standard GF composite[2]
Nozzle clog risk1–5Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its FR-ABS, only an 80 °C pre-dry[17]Moderate — needs dry filament and a clean nozzle; Prusa lists higher risk of nozzle clogging for glass-filled composites[18]
Heat-creep / jam sensitivity1–5Slightly sensitive[14]Not documented
Hotend requirementNo special hot-end required[14]Hardened steel or ruby nozzle; Polymaker's own slicer preset sets a minimum nozzle hardness of 40 HRC[2]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[5][19][17]Moderate — the PLA matrix takes up 0.40–0.51 % saturated; no glass-filled grade publishes its own figure[20][21]
Drying temperature & timeNot documented60 °C for 6 h (Polymaker HT-PLA-GF)[2]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[22]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[22]Polymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures for this grade; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[22]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[22]Not documented
Mechanical Properties
Tensile strength (XY)MPa45 at break (printed XY, ISO 527)[1]50.1 as printed and 50.2 annealed, printed XY, ISO 527 (Polymaker); eSUN quotes 59.3 by GB/T 1040[2][3]
Young's modulusMPa1990 (printed XY, ISO 527)[1]3794 as printed, 4207 annealed, printed XY, ISO 527 (Polymaker)[2]
Elongation at break%4 at break (printed XY, ISO 527) — well below the 10 % of unfilled 3DXTech ABS[1][23]2.77 as printed, 2.3 annealed, printed XY, ISO 527 (Polymaker); eSUN quotes 7.99[2][3]
Flexural strengthMPa80 (printed XY, ISO 178)[1]86.4 printed XY, ISO 178 (Polymaker)[2]
Flexural modulusMPa2250 (printed XY, ISO 178)[1]3685 printed XY, ISO 178 (Polymaker); eSUN quotes 4415 flexural modulus by GB/T 9341[2][3]
Charpy impact, notchedkJ/m²Not documented5.31 ± 0.46 as printed and 4.92 ± 0.50 annealed (printed XY, ISO 179, notched); Z 4.28 ± 0.18[2]
Other impact dataNot documentedIzod 10.16 kJ/m² (eSUN, GB/T 1843)[3]
Layer adhesion / Z tensileMPaNot documented23.7 as printed, 22.5 annealed, printed Z, ISO 527 (Polymaker)[2]
Brittleness1–5Moderate — elongation at break falls to 4 % from 10 % for the unfilled grade[1][23]Very brittle — elongation at break 2.77 % in XY and 0.85 % in Z[2]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 105 °C keeps room-temperature service far below softening[1][23]Poor — no GF-grade creep test; plain printed PLA sagged from 12 to 16.2–21.8 mm over 5 days at 1.25 kg[24][25][26]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 4 % against 10 % for unfilled 3DXTech ABS[1][23]Poor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength and elongation at break falls to 2.77 % in XY and 0.85 % in Z[27][2]
Elasticity / flexibility1–5Rigid[1]Rigid[2]
Z strength as % of XY%Not documented47 as printed (23.7 Z against 50.1 XY), printed[2]
Wear resistance & frictionNot documentedeSUN describes high wear resistance and positions the grade for wear parts[3]
Thermal Properties
HDT at 0.45 MPa°CNot documented75.5 as printed, 114.7 after annealing (ISO 75, 0.45 MPa) — the point of the material[2]
HDT at 1.8 MPa°CNot documented59.7 as printed, 84 after annealing (ISO 75, 1.8 MPa)[2]
Glass transition (Tg)°C105 (DSC)[1]59.8 (DSC)[2]
Melting point / Vicat°CNot documented174.9 peak melt (DSC); Vicat 148.9 as printed, 148.3 annealed[2]
Annealing responseNot documentedAnnealing lifts HDT at 0.45 MPa from 75.5 to 114.7 °C and modulus from 3794 to 4207 MPa[2]
Flammability / UL 94UL 94 V-0 at 1.5 mm, rated on the base resin rather than the printed part[1]Not documented
Environment & Chemical
UV resistance1–5Not documentedDegrades within weeks outdoors[28]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[29]Not documented
Food contactNot food safe — Polymaker cites potential chemical leaching[16]Not documented
Biodegradability / compostabilityNot biodegradable[16]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[16]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[30][13]Low hazard — minimal VOC and particle emission[30]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[30]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[30]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[30][13]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[30][13]None needed in a normal room[30]
Dust & fibre handling hazardNot documentedGlass fibre is bound in the matrix; avoid inhaling sanding dust[31]
Post-Processing
Sanding & machiningSands well and takes filler before painting[16]Not documented
Painting & finishingPaints readily after light abrasion[16]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[32][13]Not documented
Dimensional accuracy & detailNot documentedNear-zero shrinkage — 0.05 % in X-Y and Z (Polymaker)[2]
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[33][29]Chloroform dissolves the PLA matrix (10 % w/v, 2–4 h at 23 °C) and leaves the filler as loose sludge; laboratory reagent.[34]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[33][35]Acetone, ethyl acetate and toluene plasticise the matrix but dissolve <1 % even at 65 °C; acetone submersion crazes parts.[34][36]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[36]Chloroform vapour attacks only the resin fraction, so the filler is left standing proud; no workshop-safe agent exists.[37][36]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Firewire Flame Retardant ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Polymaker HT-PLA-GF Technical Data Sheet V1.1 Polymaker · 2026-08 · tds
  3. eSUN ePLA-GF Technical Data Sheet V1.0 (Nov 2023) eSUN (copy hosted on 3d.nice-cdn.com) · 2023-11 · tds
  4. Bambu Filament Technical Data Sheet V1.0 — PLA Galaxy Bambu Lab · 2026-08 · tds
  5. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  6. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  7. SUNLU ABS-FR (ABS Flame Retardant) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  8. YXPOLYER ABS Flame-Retardant product page YXPOLYER · 2026-08 · vendor
  9. Flame Retardant Black ABS Coex 3D · 2026-08 · vendor
  10. Polymaker HT-PLA-GF — product page Polymaker Shop · 2026-08 · vendor
  11. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  12. Polymaker product catalogue Polymaker · 2026-08 · vendor
  13. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  14. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  15. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  16. ABS — material basics Polymaker Wiki · 2026-08 · doc
  17. FIREWIRE FR-ABS — product page (print recommendations) 3DXTech · 2026-08 · doc
  18. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  19. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  20. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  21. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  22. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  23. 3DXMAX ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  24. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  25. Polymaker PLA Pro vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  26. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  27. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  28. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  29. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  30. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  31. StoneFil safety data sheet Formfutura · 2026-08 · msds
  32. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  33. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  34. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  35. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  36. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  37. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper