3D Printing Info

Filament comparison

ABS-ESD vs PLA Stone

Compare printing settings, strength, heat resistance, dated prices and sources.

ESD-safe ABS guideStone-filled PLA guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-ESD comparisonsMore PLA Stone comparisons
ABS-ESD vs PLA Stone — documented properties and sources
PropertyESD-safe ABSABSStone-filled PLAPLA
Market snapshot
Listing priceUSD/kg; dated snapshots$102.50/kg median; $47.00–$166.67/kg across 4 dated product listings$22.99/kg median; $15.99–$49.16/kg across 6 dated product listings
Identity & Market
Base polymer / chemistryABS compounded with a conductive carbon filler for static-dissipative parts[1]PLA filled with stone or mineral powder — Formfutura StoneFil declares 40–50 wt% stone powder[2][3]
Densityg/cm³1.09 (ISO 1183)[1]1.22 (Bambu Lab PLA Marble) and 1.50–1.70 (Formfutura StoneFil), ISO 1183[3][2]
Typical priceUSD/kg1 kg-equivalent spools span 47–167; the middle of the market is about 103[4][5][6]1 kg spools cluster near 21[7][8]
Price range across brandsUSD/kg47–167 across brands; IEMAI 47, YXPOLYER 65, 3DXTech 140 at 750 g pricing; the EMI-shielding ABS grade runs 167[4][5][6]16–49 across brands; SUNLU 16, ELEGOO 19, Polymaker 21, Bambu Lab 25, Prusament 38, Filament PM MarbleJet 49 on 0.5 kg spools[9][8][7][10][11][12]
Market availability1–5Niche, a handful of specialist brands[4]Stocked by most mainstream brands[7][8][9]
Spool sizes & diameters1.75 and 2.85 mm; 750 g spools[4]1.75 and 2.85 mm; 0.5 and 1 kg spools plus refills[8][2]
Typical applicationsElectronics handling fixtures, trays and jigs used around static-sensitive parts[1]Architectural models, sculpture and props with a matte mineral surface[3]
Printing Parameters
Nozzle temperature°CNot documented190–230 (Bambu Lab)[3]
Bed temperature°CNot documented35–45 (Bambu Lab)[3]
Enclosure / chamber requirement1–5Enclosure recommended[13]Open frame is fine[3]
Part cooling fanNot documentedFan on[3]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[13][14]Not documented
Warping tendency1–5High — enclosure needed for reliable large parts[13]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[13]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[15]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile[13]Easy — minor profile tuning; 0.2 mm nozzles are not usable[16]
Extruder requirementNot documentedNozzles below 0.4 mm are not compatible (Bambu Lab)[16]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[1]Brass acceptable; hardened steel for volume work — Bambu Lab's compatibility table says no hardened nozzle is needed while the note under the same table groups PLA Marble with particle-filled materials that should always use one[16]
Abrasiveness1–5Moderately abrasive — conductive carbon filler[1]Moderately abrasive — stone fill[16][2]
Nozzle clog risk1–5Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its ESD-ABS, only an 80 °C pre-dry[17]Moderate — needs dry filament and a clean nozzle[16]
Heat-creep / jam sensitivity1–5Slightly sensitive[14]Not documented
Hotend requirementNo special hot-end required[14]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[18][19][17]Moderate — 0.44 % saturated at 25 °C / 55 % RH[3]
Equilibrium moisture content at ~50 % RH%Not documented0.44 saturated at 25 °C / 55 % RH (Bambu Lab)[3]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[20]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[20]Polymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures for this grade; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[20]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[20]Not documented
Mechanical Properties
Tensile strength (XY)MPa58 at break (printed XY, ISO 527) — the conductive filler raises strength above the unfilled grade's 42[1][21]33 ± 4 printed XY, ISO 527 (Bambu Lab)[3]
Young's modulusMPa2130 (printed XY, ISO 527)[1]2330 ± 240 printed XY, ISO 527 (Bambu Lab)[3]
Elongation at break%4 at break (printed XY, ISO 527)[1]6.7 ± 0.5 printed XY, ISO 527 (Bambu Lab)[3]
Flexural strengthMPa80 (printed XY, ISO 178)[1]75 ± 5 printed XY, ISO 178 (Bambu Lab)[3]
Flexural modulusMPa2275 (printed XY, ISO 178)[1]2920 ± 180 printed XY, ISO 178 (Bambu Lab)[3]
Charpy impact, notchedkJ/m²Not documented9.5 ± 2.6 printed XY, ISO 179, notched (Bambu Lab)[3]
Other impact dataNot documentedCharpy unnotched 24.0 printed XY (Bambu Lab, ISO 179)[3]
Layer adhesion / Z tensileMPaNot documented30 ± 4 printed Z, ISO 527 (Bambu Lab)[3]
Brittleness1–5Moderate[1]Brittle — snaps with little warning[3]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 105 °C keeps room-temperature service far below softening[1]Poor — no stone-filled creep test; plain printed PLA sagged from 12 to 16.2–21.8 mm over 5 days at 1.25 kg[22][23][24]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break 4 %, well below unfilled ABS[1][21]Poor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength and the mineral filler leaves a brittle compound[25][3]
Elasticity / flexibility1–5Rigid[1]Rigid[3]
Z strength as % of XY%Not documented91 by tensile, 73 by flexural (printed, Bambu Lab)[3]
Thermal Properties
HDT at 0.45 MPa°CNot documented56 (ISO 75, 0.45 MPa)[3]
HDT at 1.8 MPa°CNot documented53 (ISO 75, 1.8 MPa)[3]
Glass transition (Tg)°C105 (DSC)[1]56 (DSC)[3]
Melting point / Vicat°CNot documented156 peak melt (DSC); Formfutura gives a 120–170 melting range for StoneFil[3][2]
Environment & Chemical
UV resistance1–5Not documentedDegrades within weeks outdoors[26]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[27]Not documented
Food contactNot food safe — Polymaker cites potential chemical leaching[15]Not documented
Biodegradability / compostabilityNot biodegradable[15]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[15]Not documented
Electrical & ESD propertiesSurface resistance 10⁷–10⁹ ohm/sq, the static-dissipative band (ASTM D257), against above 10¹³ for unfilled ABS[1][21]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[28][13]Low hazard — minimal VOC and particle emission[28]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[28]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[28]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[28][13]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[28][13]None needed in a normal room[28]
Dust & fibre handling hazardConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[1]Formfutura's SDS sets an occupational limit of 1 mg/m³ for the stone powder and lists it as both a fibre and a particulate — do not dry-sand without extraction[2]
Post-Processing
Sanding & machiningSands well and takes filler before painting[15]Sands to a stone-like matte surface[2]
Painting & finishingPaints readily after light abrasion[15]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[29][13]Support for PLA (Bambu Lab)[3]
Dimensional accuracy & detailNot documentedMatte mineral surface hides layer lines; 55° overhangs and 30 mm bridges as for plain PLA[3]
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[30][27]Chloroform dissolves the PLA matrix (10 % w/v, 2–4 h at 23 °C) and leaves the filler as loose sludge; laboratory reagent.[31]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[30][32]Acetone, ethyl acetate and toluene plasticise the matrix but dissolve <1 % even at 65 °C; acetone submersion crazes parts.[31][33]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[33]Chloroform vapour attacks only the resin fraction, so the filler is left standing proud; no workshop-safe agent exists.[34][33]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. 3DXSTAT ESD-ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. StoneFil safety data sheet Formfutura · 2026-08 · msds
  3. Bambu Filament Technical Data Sheet — PLA Marble Bambu Lab · 2026-08 · tds
  4. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  5. IEMAI ESD-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  6. YXPOLYER ABS ESD product page YXPOLYER · 2026-08 · vendor
  7. PLA Marble — product page Bambu Lab US Store · 2026-08 · vendor
  8. Polymaker product catalogue Polymaker · 2026-08 · vendor
  9. ELEGOO product catalogue ELEGOO · 2026-08 · vendor
  10. Printed Solid product catalogue Printed Solid · 2026-08 · vendor
  11. SUNLU High Speed PLA Marble 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  12. Filament PM PLA MarbleJet technical data sheet Filament PM (Plasty Mladec) · 2026-08 · tds
  13. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  14. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  15. ABS — material basics Polymaker Wiki · 2026-08 · doc
  16. PLA Usage Guide Bambu Lab Wiki · 2026-08 · doc
  17. 3DXSTAT ESD-ABS — product page (print recommendations) 3DXTech · 2026-08 · doc
  18. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  19. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  20. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  21. 3DXMAX ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  22. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  23. Polymaker PLA Pro vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  24. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  25. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  26. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  27. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  28. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  29. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  30. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  31. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  32. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  33. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  34. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper