3D Printing Info

Filament comparison

ABS-ESD vs PEEK-CF

Compare printing settings, strength, heat resistance, dated prices and sources.

ESD-safe ABS guideFibre-reinforced PEEK guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-ESD comparisonsMore PEEK-CF comparisons
ABS-ESD vs PEEK-CF — documented properties and sources
PropertyESD-safe ABSABSFibre-reinforced PEEKHIGHTEMP
Market snapshot
Listing priceUSD/kg; dated snapshots$102.50/kg median; $47.00–$166.67/kg across 4 dated product listings$597.50/kg median; $448.00–$695.00/kg across 5 dated product listings
Identity & Market
Base polymer / chemistryABS compounded with a conductive carbon filler for static-dissipative parts[1]Short-fibre reinforced PEEK. 3DXTech's CarbonX grade is nominally 10 wt% carbon and its FibreX grade 20 wt% glass; LEHVOSS Luvocom 3F PEEK CF 9676 is 15 wt% carbon; Ensinger's machining stock runs to 30 wt% carbon[2][3][4][5]
Densityg/cm³1.09 (ISO 1183)[1]1.39 (ISO 1183)[2]
Typical priceUSD/kg1 kg-equivalent spools span 47–167; the middle of the market is about 103[3][6][7]1 kg-equivalent spools span 448–972; the middle of the market is about 598[3][4][8]
Price range across brandsUSD/kg47–167 across brands; IEMAI 47, YXPOLYER 65, 3DXTech 140 at 750 g pricing; the EMI-shielding ABS grade runs 167[3][6][7]448-972 across formats and filler types; IEMAI 3D CF-PEEK and GF-PEEK 448 at 1 kg, 3DXTech CarbonX PEEK+CF10 598 at 2 kg and FibreX PEEK+GF20 695 at 1 kg, Luvocom 3F PEEK CF 9676 648 at 2 kg[3][4][8][9]
Market availability1–5Niche, a handful of specialist brands[3]Niche, a handful of specialist brands[3][4]
Spool sizes & diameters1.75 and 2.85 mm; 750 g spools[3]1.75 and 2.85 mm; 200 g to 2 kg spools[3][4]
Typical applicationsElectronics handling fixtures, trays and jigs used around static-sensitive parts[1]Stiff aerospace and oil-and-gas parts where PEEK alone is not rigid enough[2]
Printing Parameters
Enclosure / chamber requirement1–5Enclosure recommended[10]Actively heated chamber required[11][12]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[10][13]Not documented
Warping tendency1–5High — enclosure needed for reliable large parts[10]Moderate — needs adhesion aid or draught shield; the fibre cuts PEEK's crystallisation shrinkage[2]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[10]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[14]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile[10]Expert / industrial hardware only[11][12]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[1]Hardened steel required[2]
Abrasiveness1–5Moderately abrasive — conductive carbon filler[1]Highly abrasive — standard CF composite[2]
Nozzle clog risk1–5Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its ESD-ABS, only an 80 °C pre-dry[15]High — jams from moisture, heat creep or particles; 3DXTech adds a hardened 0.4 mm minimum nozzle and 0.25 mm layers to the mandatory 120 °C pre-dry[16][17]
Heat-creep / jam sensitivity1–5Slightly sensitive[13]Not documented
Hotend requirementNo special hot-end required[13]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[18][19][15]Not documented
Equilibrium moisture content at ~50 % RH%Not documented0.06 in 24 h on extruded CF30 stock (ASTM D570)[5]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[20]Not documented
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[20]No dry-versus-conditioned figures are published; 3DXTech mandates a 120 °C, 4 h pre-dry before every print because trapped water flashes to steam at these nozzle temperatures[16]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[20]Not documented
Mechanical Properties
Tensile strength (XY)MPa58 at break (printed XY, ISO 527) — the conductive filler raises strength above the unfilled grade's 42[1][21]105 at break (printed XY, ISO 527, CF10); 121 at yield on extruded CF30 stock (ASTM D638)[2][5]
Young's modulusMPa2130 (printed XY, ISO 527)[1]8100 (printed XY, ISO 527, CF10) — more than double unfilled PEEK; 6343 on extruded CF30 stock (ASTM D638)[2][5]
Elongation at break%4 at break (printed XY, ISO 527)[1]3 at break (printed XY, ISO 527), against 28 for unfilled PEEK[2][22]
Flexural strengthMPa80 (printed XY, ISO 178)[1]136 (printed XY, ISO 178, CF10); 193 on extruded CF30 stock (ASTM D790)[2][5]
Flexural modulusMPa2275 (printed XY, ISO 178)[1]8300 (printed XY, ISO 178, CF10); 7171 on extruded CF30 stock (ASTM D790)[2][5]
Other impact dataNot documentedIzod notched 61.9 J/m on extruded CF30 stock, converted from 1.16 ft-lb/in (ASTM D256)[5]
Brittleness1–5Moderate[1]Brittle — snaps with little warning; elongation falls from 28 % to 3 %[2][22]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documentedRockwell M107 on extruded PEEK-CF30 stock (ASTM D785), against M100 unfilled[5][23]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 105 °C keeps room-temperature service far below softening[1]Excellent — holds load for years. Ensinger rates carbon-fibre PEEK stock as very highly creep resistant and specifies 260 °C continuous service[5]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break 4 %, well below unfilled ABS[1][21]Good. Victrex rates PEEK for long-term fatigue as well as creep; the fibre cuts elongation at break from 28 % to 3 %, which limits repeated large-strain flexing[24][2][22]
Elasticity / flexibility1–5Rigid[1]Rigid[2]
Thermal Properties
HDT at 0.45 MPa°CNot documented265 (printed XY, ISO 75 at 0.45 MPa, CarbonX PEEK+CF10) against 140 for unfilled PEEK[2][22]
HDT at 1.8 MPa°CNot documented316 on extruded CF30 stock, converted from 600 °F at 264 psi (ASTM D648)[5]
Glass transition (Tg)°C105 (DSC)[1]143 (DSC, CarbonX PEEK+CF10) — the fibre does not move the glass transition[2]
Melting point / Vicat°CNot documented334 melting on extruded CF30 stock, converted from 633 °F[5]
Continuous service temperature°CNot documented260 long-term on extruded CF30 stock, converted from 500 °F; 300 short term[5]
Thermal expansion (CTE)µm/m·KNot documented14.4 (extruded PEEK-CF30 stock, ASTM D696; source states 0.80e-5 in/in/°F) — about a third of unfilled PEEK[5][23]
Flammability / UL 94Not documentedUL 94 V-0 on the base resin; Ensinger lists extruded PEEK-CF30 stock as inherently flame resistant[22][5]
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[25]Not documented
Food contactNot food safe — Polymaker cites potential chemical leaching[14]Not documented
Biodegradability / compostabilityNot biodegradable[14]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[14]Not documented
Electrical & ESD propertiesSurface resistance 10⁷–10⁹ ohm/sq, the static-dissipative band (ASTM D257), against above 10¹³ for unfilled ABS[1][21]Surface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[2]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[26][10]Moderate — measurable VOCs and UFPs, ventilation advised. None of these polymers was in the chamber study, and all are processed far above the temperatures it covered[26]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[26]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[26]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[26][10]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[26][10]Ventilated room or enclosure recommended[26]
Dust & fibre handling hazardConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[1]Carbon fibre is bound in the matrix; sanding dust should not be inhaled[2]
Post-Processing
Sanding & machiningSands well and takes filler before painting[14]Not documented
Painting & finishingPaints readily after light abrasion[14]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[27][10]Not documented
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[28][25]95–98 wt% sulphuric acid dissolves the matrix at 40–70 °C and leaves the fibre. Nothing else touches PEEK.[29][28]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[28][30]Concentrated nitric, hydrofluoric, hydrobromic and hydriodic acids attack it; DCM, DMSO and THF swell thin-walled sections.[31][28]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[32]None — no solvent softens PEEK, so parts are joined thermally or mechanically, never chemically.[31][28]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. 3DXSTAT ESD-ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. CarbonX Carbon Fiber PEEK Technical Data Sheet v3 3DXTech · 2026-08 · tds
  3. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  4. 3D4Makers product catalogue 3D4Makers · 2026-08 · vendor
  5. TECAPEEK CF30 black (PEEK-CF30) — stock shape properties Ensinger · 2026-08 · tds
  6. IEMAI ESD-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  7. YXPOLYER ABS ESD product page YXPOLYER · 2026-08 · vendor
  8. IEMAI 3D CF-PEEK 3D Printing Filament — store page IEMAI 3D · 2026-08 · vendor
  9. IEMAI 3D GF-PEEK 3D Printing Filament — store page IEMAI 3D · 2026-08 · vendor
  10. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  11. Prusament PEI 1010 Technical Datasheet v1.0 Prusa Polymers · 2024-09 · tds
  12. Prusament PEI 1010 — material page Prusa Polymers · 2026-08 · doc
  13. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  14. ABS — material basics Polymaker Wiki · 2026-08 · doc
  15. 3DXSTAT ESD-ABS — product page (print recommendations) 3DXTech · 2026-08 · doc
  16. CARBONX PEEK+CF10 — product page (print recommendations) 3DXTech · 2026-08 · doc
  17. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  18. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  19. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  20. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  21. 3DXMAX ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  22. ThermaX PEEK Technical Data Sheet v3 3DXTech · 2026-08 · tds
  23. TECAPEEK natural (PEEK) — stock shape properties Ensinger · 2026-08 · tds
  24. PEEK polymers — product overview Victrex · 2026-08 · doc
  25. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  26. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  27. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  28. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  29. The Effects of Sulfonated Poly(ether ether ketone) Ion Exchange Preparation Conditions on Membrane Properties Yee, Zhang & Ladewig, Membranes 3(3) 182–195 · 2013-07 · paper
  30. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  31. What solvents are not compatible with PEEK? — fluidics technical FAQ IDEX Health & Science · 2026-08 · doc
  32. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc