3D Printing Info

Filament comparison

ABS-CF vs PLA Matte

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guideMatte PLA guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore PLA Matte comparisons
ABS-CF vs PLA Matte — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSMatte PLAPLA
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$19.09/kg median; $10.99–$32.16/kg across 10 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]PLA compounded with a mineral filler — Fiberlogy names chalk — that scatters light into a diffuse finish[2][3]
Densityg/cm³1.11 (ISO 1183)[1]1.31 (Bambu Lab, ISO 1183) to 1.38 (Fiberlogy PLA Mineral, method not stated) — above plain PLA from the filler[3][2]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[4][5][6][7][8]Mainstream 1 kg spools cluster near 21[9][10][11]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[4][5][6][7][12][8]11–32 across brands; budget house brands 11–19, Fiberlogy PLA Mineral 32[13][10][14]
Market availability1–5Available from several mainstream brands[4][5]Stocked by most mainstream brands[13][11][9]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[4][5]1.75 mm; 1 kg spools plus spool-less refills[9][15]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]Display models and visible parts where a matte, non-reflective finish matters[3]
Diameter tolerance± mmNot documented±0.03 (Bambu Lab)[16]
Printing Parameters
Nozzle temperature°CNot documented190–230 (Bambu Lab); 190–210 (Fiberlogy PLA Mineral)[3][2]
Bed temperature°CNot documented35–45 (Bambu Lab); 60 (Fiberlogy)[3][2]
Enclosure / chamber requirement1–5Enclosure recommended[17]Open frame is fine[3][2]
Part cooling fanNot documentedFan on; Fiberlogy specifies 75–100 %[3][2]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[17][18]Cool plate, high-temperature plate or textured PEI with glue (Bambu Lab); smooth PEI, textured PEI or glass (Fiberlogy)[3][2]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[17]None[3]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[17]Sticks to anything[19]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[20]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[17]Beginner — prints on any machine out of the box[3][2]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[17]Brass fine indefinitely[21][3][2]
Abrasiveness1–5Highly abrasive — standard CF composite[17]Slightly abrasive — mineral filler pushes density from 1.24 to 1.31–1.38[2][3][22]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[23][24][25]Very low[21]
Heat-creep / jam sensitivity1–5Slightly sensitive[18]Moderate — good heatbreak cooling needed; PLA softens below 60 °C[26]
Hotend requirementNo special hot-end required[18]No special hot-end required[19]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[27][28][23]Moderate — 0.40 % saturated at 25 °C / 55 % RH[3]
Equilibrium moisture content at ~50 % RH%Not documented0.40 saturated at 25 °C / 55 % RH (Bambu Lab)[3]
Drying temperature & timeNot documented50 °C for 8 h in a forced-air dryer, or 60–70 °C for 12 h on an X1 heatbed; Fiberlogy specifies 50 °C for 6 h[3][2][29]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[30]Bubbling and popping at the nozzle, stringing, rough surface and weak layers[30]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[30]Polymaker rates PLA low-sensitivity — the loss shows as poor layer adhesion and brittle layers rather than a published strength figure[30]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[30]Sealed with desiccant below 20 % RH; shelf life at ambient is long[22][19]
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]30 (printed XY, ISO 527, Bambu Lab); 35.1 on My Tech Fun bars for PolyTerra PLA[3][31]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]1960 (Bambu Lab, printed XY, ISO 527); Fiberlogy PLA Mineral quotes 3500 (ISO 527, specimen type not stated)[3][2]
Elongation at break%2 at break (printed XY, ISO 527)[1]14.8 (printed XY, ISO 527)[3]
Flexural strengthMPa76 (printed XY, ISO 178)[1]53 (printed XY, ISO 178) — 30 % below PLA Basic at 76[3][22]
Flexural modulusMPa5260 (printed XY, ISO 178)[1]2360 (printed XY, ISO 178)[3]
Charpy impact, notchedkJ/m²Not documented6.3 (printed XY, ISO 179, notched); unnotched 19.2[3]
Other impact dataNot documentedIzod 6.1 kJ/m² on My Tech Fun printed bars for PolyTerra PLA[31]
Layer adhesion / Z tensileMPaNot documented22 (printed Z, ISO 527); flexural Z falls to 29 against 53 in XY; 12.9 on My Tech Fun layer-adhesion bars[3][31]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Brittle — snaps with little warning[3]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][27][28]Poor — 12 mm bar sagged to 18.7 mm over 5 days at 1.25 kg[31]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][27]Poor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength (R = 0.2)[32][26]
Elasticity / flexibility1–5Rigid[1]Rigid[3]
Z strength as % of XY%Not documented73 by tensile, 55 by flexural (printed, Bambu Lab)[3]
Thermal Properties
HDT at 0.45 MPa°CNot documented58 (Bambu Lab) and 48 (Fiberlogy PLA Mineral), ISO 75 at 0.45 MPa[3][2]
HDT at 1.8 MPa°CNot documented52 (ISO 75, 1.8 MPa)[3]
Glass transition (Tg)°C105 (DSC)[1]61 (DSC)[3]
Melting point / Vicat°CNot documented163 peak melt (DSC); Vicat 63 °C[3]
Continuous service temperature°CNot documented54 — loaded bars begin to move at this temperature[31]
Annealing responseNot documented50–60 °C for 6–12 h; some prints deform or warp, and a forced-air oven is required[3]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[33]Not documented
Flammability / UL 94Not documentedFlammable; no UL 94 rating published by the major brands[22][34]
Environment & Chemical
UV resistance1–5Not documentedDegrades within weeks outdoors[26][35]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[36]Good against weak acids, oils and grease; poor against strong acids and alkalis; dissolved by chloroform, THF and hot benzene[34][26]
Water / humidity resistance in service1–5Not documentedGood — insoluble in water[22]
Food contactNot food safe — Polymaker cites potential chemical leaching[20]Base resin is food-contact grade, but printed layer grooves harbour bacteria; Prusa advises against food use[26]
Biodegradability / compostabilityNot biodegradable[20]Industrially compostable only — needs sustained 55 °C; not home compostable[37][26]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[20]Mechanically recyclable; not accepted in household plastic collection[37]
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[38][17]Low hazard — minimal VOC and particle emission[38]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[38]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[38]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[38][17]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[38][17]None needed in a normal room[38]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[20]Wet sanding — dry sanding heats the surface by friction and smears it[35][26]
Painting & finishingPaints readily after light abrasion[20]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate for most joints; some grades partially dissolve and bond with acetone[26][39]
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[36]No practical vapour smoothing — only chloroform, hot benzene or THF, which are laboratory-only[26]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[40][17]Support for PLA (Bambu Lab)[3]
Dimensional accuracy & detailNot documentedMatte surface hides layer lines; 55° overhangs and 30 mm bridges as for plain PLA[3]
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[41][36]Chloroform: 10 % w/v in 2–4 h at 23 °C, every grade and morphology; THF and DMF only at 65 °C. Laboratory reagents.[42]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[41][43]Acetone, ethyl acetate and toluene plasticise it but dissolve <1 % even at 65 °C; submersion in acetone crazes and destroys parts.[42][44]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[44][36]Chloroform vapour smooths and welds PLA at the cost of tensile strength; acetone does not smooth it at all.[45][44]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. PLA Mineral — product and technical data Fiberlogy · 2026-08 · tds
  3. Bambu Filament Technical Data Sheet V3.0 — PLA Matte Bambu Lab · 2026-08 · tds
  4. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  5. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  6. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  7. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  8. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  9. Polymaker Panchroma Matte PLA — product listing 3DJake International · 2026-08 · vendor
  10. Overture Matte PLA 1.75mm Overture3D · 2026-08 · vendor
  11. Matte PLA filament collection Anycubic Official Store · 2026-08 · vendor
  12. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  13. Matte PLA filament collection Sunlu Official Store · 2026-08 · vendor
  14. Fiberlogy PLA Mineral — product listing 3DJake International · 2026-08 · vendor
  15. Extrudr PLA NX2 Matt — product listing 3DJake International · 2026-08 · vendor
  16. PLA Basic — product page Bambu Lab US Store · 2026-08 · vendor
  17. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  18. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  19. PLA — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  20. ABS — material basics Polymaker Wiki · 2026-08 · doc
  21. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  22. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  23. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  24. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  25. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  26. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  27. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  28. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  29. Filament Drying Recommendations Bambu Lab Wiki · 2026-08 · doc
  30. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  31. PolyTerra PLA vs PLA+ — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  32. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  33. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  34. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  35. Prusament PLA Technical Data Sheet v1.0 Prusa Polymers · 2018-09 · tds
  36. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  37. Filamentive PLA (recycled) — product page Filamentive · 2026-08 · vendor
  38. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  39. Prusament rPLA Corn Pigment 1kg — product page Prusa Research · 2026-08 · vendor
  40. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  41. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  42. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  43. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  44. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  45. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper