3D Printing Info

Filament comparison

ABS-CF vs PA blend

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guidePA6/66 copolymer blends guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore PA blend comparisons
ABS-CF vs PA blend — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSPA6/66 copolymer blendsPA
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$65.62/kg median; $62.00–$113.33/kg across 4 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]PA6/66 copolymer — a nylon alloy that lowers the melting point and improves printability against straight PA6[2][3]
Densityg/cm³1.11 (ISO 1183)[1]1.12 (ISO 1183, Polymaker CoPA)[2]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[4][5][6][7][8]1 kg-equivalent spools cluster near 65[9][10][11]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[4][5][6][7][12][8]62–113 across brands; add:north Adura 62, PrimaCreator NylonPower PA6/66 65 at 500 g, Polymaker CoPA 67, 3DXTech AmideX Nylon 6-66 113[9][4][10][11]
Market availability1–5Available from several mainstream brands[4][5]Available from several mainstream brands[9][4]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[4][5]1.75 and 2.85 mm; 0.5, 0.75 and 1 kg spools[9][4][10][11]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]General-purpose nylon parts and, unusually, CoPA can support itself if the support is removed before it absorbs moisture[2]
Printing Parameters
Nozzle temperature°CNot documented250–270 (Polymaker CoPA)[2]
Bed temperature°CNot documented25–50 (Polymaker CoPA)[2]
Enclosure / chamber requirement1–5Enclosure recommended[13]Enclosure required (passive) — Polymaker specifies a chamber at ambient temperature[2]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[13][14]Not documented
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documented16 at Polymaker's 200 mm/s cap on a 0.4 mm nozzle at 0.2 mm layer[2][15]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[13]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[13]Not documented
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[16]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[13]Advanced — enclosure, hardware upgrades, tuning; must be kept below 20 % RH throughout[2][17]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[13]Brass fine indefinitely for unfilled grades[18]
Abrasiveness1–5Highly abrasive — standard CF composite[13]Non-abrasive when unfilled[18]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[19][20][21]Very high — frequent jams without careful setup[22][17]
Heat-creep / jam sensitivity1–5Slightly sensitive[14]Not documented
Hotend requirementNo special hot-end required[14]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[23][24][19]Very high (>2 %) — Polymaker's own wet-state specimens reached 6.16 % moisture content after 48 h immersion at 60 °C[2][17]
Drying temperature & timeNot documented100 °C for 8 h (Polymaker CoPA)[2]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[17]Popping and cracking during extrusion, then hard-to-diagnose defects[22]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[17]Measured dry against wet on printed specimens at 6.16 % moisture (Polymaker CoPA): tensile 78.0 → 34.3 MPa, Young's modulus 2703 → 724 MPa, flexural strength 109.8 → 22.6 MPa, while notched Charpy rises 6.9 → 27.7 kJ/m² and elongation 12.7 → 13.2 %[2][22]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[17]Polymaker states CoPA must always be stored and used below 20 % relative humidity[2]
Hydrolysis at melt temperatureNot documentedPolymaker requires a 100 °C dry for 8 h and storage below 20 % RH; no molecular-weight loss figure is published, and the published wet data is conditioning rather than melt hydrolysis[2][25]
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]78.0 ± 0.7 printed XY dry and 34.3 ± 2.5 wet, ISO 527 (Polymaker CoPA)[2]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]2703 ± 259 printed XY dry and 724 ± 61 wet, ISO 527 (Polymaker CoPA)[2]
Elongation at break%2 at break (printed XY, ISO 527)[1]12.7 ± 2.1 printed XY dry and 13.2 ± 2.3 wet, ISO 527 (Polymaker CoPA)[2]
Flexural strengthMPa76 (printed XY, ISO 178)[1]109.8 ± 1.3 printed XY dry and 22.6 ± 0.5 wet, ISO 178 (Polymaker CoPA)[2]
Flexural modulusMPa5260 (printed XY, ISO 178)[1]2510 ± 25 printed XY dry and 636 ± 11 wet, ISO 178 (Polymaker CoPA)[2]
Charpy impact, notchedkJ/m²Not documented6.9 ± 1.4 printed XY dry and 27.7 ± 1.2 wet, ISO 179 notched (Polymaker CoPA) — impact quadruples when conditioned[2]
Layer adhesion / Z tensileMPaNot documented45.8 ± 1.5 printed Z dry, falling to 13.7 ± 1.2 wet, ISO 527 (Polymaker CoPA)[2]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Tough — absorbs impact, yields before breaking[2]
Hardness (scale-specific)Shore A / Shore D / RockwellNot documentedShore D 86 and Rockwell 85 (108) — the source does not name the scales on extruded unfilled PA66 stock (ASTM D2240, D785)[26]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][23][24]Not documented
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][23]Excellent — living hinges viable[18]
Elasticity / flexibility1–5Rigid[1]Semi-flexible[22]
Z strength as % of XY%Not documented59 dry (45.8 Z against 78.0 XY) and 40 wet, printed[2]
Thermal Properties
HDT at 0.45 MPa°CNot documented111 (ISO 75, 0.45 MPa, Polymaker CoPA)[2]
HDT at 1.8 MPa°CNot documented70 (ISO 75, 1.8 MPa, Polymaker CoPA)[2]
Glass transition (Tg)°C105 (DSC)[1]66 (DSC, Polymaker CoPA)[2]
Melting point / Vicat°CNot documented189 melting (DSC); Vicat 180, crystallisation 148, decomposition 370 (Polymaker CoPA)[2]
Annealing responseNot documented80 °C for 6 h (Polymaker CoPA)[2]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[27]81.0 on extruded unfilled PA66 stock (ASTM D696; source states 4.5e-5 in/in/°F) — the same chemistry as a PA6/66 copolymer[26]
Environment & Chemical
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[28]Not documented
Water / humidity resistance in service1–5Not documentedAbsorbs water, properties shift — 6.16 % uptake cost 56 % of tensile strength and 73 % of modulus[2]
Food contactNot food safe — Polymaker cites potential chemical leaching[16]Not documented
Biodegradability / compostabilityNot biodegradable[16]Not documented
RecyclabilityMechanically recyclable but not accepted in household plastic collection[16]Not documented
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[29][13]Moderate — measurable VOCs and UFPs, ventilation advised[29]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[29]Up to 180 caprolactam, the dominant VOC from nylon; total VOC reached nearly 200 µg/min, the highest of the nine filaments tested[29]
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[29]≈2 × 10⁸ median — low for ultrafine particles despite the highest VOC mass of any filament tested[29]
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[29][13]Caprolactam, at up to 180 µg/min from nylon filament — the largest single-VOC emission rate measured in the study[29]
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[29][13]Ventilated room or enclosure recommended[29]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[16]Not documented
Painting & finishingPaints readily after light abrasion[16]Not documented
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[28]Not documented
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[30][13]CoPA can support itself, but Polymaker warns the support bonds permanently if it absorbs moisture before removal[2]
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[31][28]Dissolved at 23 °C by formic acid above ~50 %, phenol, m-cresol, 96 % sulphuric acid or hexafluoroisopropanol — laboratory reagents.[32]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[31][33]Zinc chloride solutions stress-crack it — 10 % marginal, 37 % not resistant; alcoholic calcium chloride dissolves it.[32]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[34][28]None — nylon's only solvents are formic acid, phenol and HFIP, all of which degrade the part they wet.[32]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. PolyMide CoPA Technical Data Sheet V5.4 (dry and wet status blocks) Polymaker · 2024-11 · tds
  3. AmideX Nylon 6-66 — product page 3DXTech · 2026-08 · vendor
  4. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  5. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  6. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  7. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  8. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  9. Polymaker product catalogue Polymaker · 2026-08 · vendor
  10. add:north Adura product page add:north · 2026-08 · vendor
  11. PrimaCreator SELECT NylonPower PA6/66 product page PrimaCreator · 2026-08 · vendor
  12. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  13. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  14. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  15. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  16. ABS — material basics Polymaker Wiki · 2026-08 · doc
  17. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  18. PA (Nylon) — material basics Polymaker Wiki · 2026-08 · doc
  19. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  20. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  21. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  22. Moisture Conditioning — effect on printed nylon properties Polymaker Wiki · 2026-08 · doc
  23. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  24. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  25. PolyMide CoPA — Technical Data Sheet page Polymaker Wiki · 2026-08 · tds
  26. TECAMID 66 natural (PA66) — stock shape properties Ensinger · 2026-08 · tds
  27. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  28. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  29. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  30. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  31. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  32. Ultramid Nylon Chemical Resistance guide (unmodified PA6 B27E and PA66 A27E) BASF · 2026-08 · tds
  33. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  34. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc