3D Printing Info

Filament comparison

ABS-CF vs ABS+

Compare printing settings, strength, heat resistance, dated prices and sources.

Carbon-fibre ABS (ABS-CF) guideABS+ / Tough ABS guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS-CF comparisonsMore ABS+ comparisons
ABS-CF vs ABS+ — documented properties and sources
PropertyCarbon-fibre ABS (ABS-CF)ABSABS+ / Tough ABSABS
Market snapshot
Listing priceUSD/kg; dated snapshots$35.99/kg median; $22.00–$125.00/kg across 7 dated product listings$26.49/kg median; $15.99–$29.99/kg across 4 dated product listings
Identity & Market
Base polymer / chemistryABS reinforced with chopped carbon fibre[1]ABS reformulated for lower warping and a higher glass transition; Polymaker's ABS Pro and ABS Max reach Tg 114.9 and 126.3 °C against 101 °C for PolyLite ABS[2][3][4]
Densityg/cm³1.11 (ISO 1183)[1]1.04 (ABS Pro) and 1.06 (ABS Max), ISO 1183[2][3]
Typical priceUSD/kg1 kg-equivalent spools span 22–125; the middle of the market is about 36[5][6][7][8][9]1 kg spools cluster near 27[10]
Price range across brandsUSD/kg22–125 across brands; IEMAI 22, Siraya Tech 28 and 36 for the core-shell grade, YXPOLYER 35, Push Plastic 50 at 2 kg, 3DXTech 64 at 750 g; Stratasys-compatible cartridges run far higher[5][6][7][8][11][9]16–30 across brands; SUNLU E-ABS 16, Polymaker ABS Pro 25, YXPOLYER ABS Enhanced 28, Polymaker ABS Max 30[10][12][13]
Market availability1–5Available from several mainstream brands[5][6]Available from several mainstream brands[10]
Spool sizes & diameters1.75 and 2.85 mm; 0.5, 0.75 and 2 kg spools plus Stratasys-compatible cartridges[5][6]1.75 and 2.85 mm; 1 kg spools[10]
Typical applicationsStiff tooling and fixtures that must survive above 100 °C[1]Large enclosure and automotive parts where plain ABS warps or softens too early[2][3]
Printing Parameters
Nozzle temperature°CNot documented270–290 (ABS Pro); 270–300 (ABS Max) — 25–35 °C above plain ABS[2][3]
Bed temperature°CNot documented120 (ABS Max)[3]
Enclosure / chamber requirement1–5Enclosure recommended[14]Enclosure required (passive)[2][3][14]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[14][15]Clean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[14][15]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sNot documentedUp to 250 mm/s (ABS Pro) and 200 mm/s (ABS Max), equivalent to 20 and 16 on a 0.4 mm nozzle at 0.2 mm layer[2][3][16]
Warping tendency1–5Moderate — needs adhesion aid or draught shield; the fibre reduces warping against unfilled ABS[14]High — enclosure needed for reliable large parts[14]
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[14]Needs a specific surface plus adhesive[14]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[17]Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[17]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; hardened nozzle mandatory[14]Intermediate — dry filament and a tuned profile; the hotter nozzle rules out PTFE-lined hotends[2][3]
Hardware Wear & Reliability
Nozzle hardness required1–4Hardened steel required[14]Brass fine indefinitely[14]
Abrasiveness1–5Highly abrasive — standard CF composite[14]Non-abrasive[14]
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle; 3DXTech specifies a hardened nozzle of 0.4 mm minimum and 0.25 mm layers or higher, and Prusa lists composites as a higher clogging risk[18][19][20]Low — unfilled ABS compound; no special hot-end required and clogging is not among the listed drawbacks[15][21]
Heat-creep / jam sensitivity1–5Slightly sensitive[15]Slightly sensitive[15]
Hotend requirementNo special hot-end required[15]No special hot-end required[15]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the ABS matrix takes up 0.51–0.65 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 80 °C, 4 h pre-dry[22][2][18]Moderate — 0.51 % maximum water absorption (ABS Pro)[2]
Equilibrium moisture content at ~50 % RH%Not documented0.51 maximum water absorption (Polymaker ABS Pro)[2]
Drying temperature & timeNot documented70 °C for 6 h (ABS Max)[3]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[23]Bubbling and popping at the nozzle, stringing and a rough surface[23]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures; absorbed water flashes to steam in the hotend and shows as bubbling and poor layer adhesion[23]Polymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures[23]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[23]Sealed with desiccant; Polymaker rates ABS moderate-sensitivity[23]
Mechanical Properties
Tensile strength (XY)MPa46 at break (printed XY, ISO 527)[1]34.9 (ABS Pro) and 35.7 (ABS Max) printed XY, ISO 527[2][3]
Young's modulusMPa5210 (printed XY, ISO 527) — more than double unfilled ABS[1]2330 (ABS Pro) and 2320 (ABS Max) printed XY, ISO 527[2][3]
Elongation at break%2 at break (printed XY, ISO 527)[1]6.7 (ABS Max) and 7.3 (ABS Pro) at break, printed XY, ISO 527[2][3]
Flexural strengthMPa76 (printed XY, ISO 178)[1]60.1 (ABS Pro) and 63.3 (ABS Max) printed XY, ISO 178[2][3]
Flexural modulusMPa5260 (printed XY, ISO 178)[1]2330 (ABS Pro) and 2500 (ABS Max) printed XY, ISO 178[2][3]
Charpy impact, notchedkJ/m²Not documented10.5 (ABS Max) and 14.5 (ABS Pro) printed XY, ISO 179, notched[2][3]
Layer adhesion / Z tensileMPaNot documented21.9 (ABS Pro) and 25.4 (ABS Max) printed Z, ISO 527[2][3]
Brittleness1–5Brittle — snaps with little warning; elongation at break 2 %[1]Tough — absorbs impact, yields before breaking[2][3]
Creep resistance / sustained load1–5Good — no creep test found; chopped carbon fibre restrains matrix flow and modulus rises to 5210 MPa against 2200–2330 for unfilled ABS[1][22][2]Moderate — no creep test found; Tg of 115 °C (ABS Pro) and 126 °C (ABS Max) keeps room-temperature service far below softening[2][3]
Fatigue / repeated-flex resistance1–5Below average — no S-N curve found; elongation at break falls to 2 % against 10.5 % for unfilled ABS[1][22]Moderate — no S-N curve found; 6.7–7.3 % elongation and 10.5–14.5 kJ/m² notched Charpy, below unfilled Bambu Lab ABS[2][3][22]
Elasticity / flexibility1–5Rigid[1]Rigid[2]
Z strength as % of XY%Not documented63 (ABS Pro) and 71 (ABS Max), printed[2][3]
Thermal Properties
HDT at 0.45 MPa°CNot documented106.4 (ABS Pro) and 118.1 (ABS Max), ISO 75 at 0.45 MPa[2][3]
HDT at 1.8 MPa°CNot documented101.4 (ABS Pro) and 113.1 (ABS Max), ISO 75 at 1.8 MPa[2][3]
Glass transition (Tg)°C105 (DSC)[1]114.9 (ABS Pro) and 126.3 (ABS Max), DSC[2][3]
Melting point / Vicat°CNot documentedAmorphous — no melting point; Vicat 116.1 (ABS Pro) and 127.4 (ABS Max), ISO 306[2][3]
Thermal expansion (CTE)µm/m·K19–25 along the print bead and 80–84 in the build direction at 30 °C (20 wt% CF, large-format printed, TMA)[24]86–89 for printed unfilled ABS (fibre Bragg grating, 25–50 °C); no grade-specific measurement published[25]
Environment & Chemical
UV resistance1–5Not documentedMonths outdoors before embrittlement[17]
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[4]Good against weak acids, weak alkalis, oils and grease; dissolved by acetone[4]
Food contactNot food safe — Polymaker cites potential chemical leaching[17]Not food safe — Polymaker cites potential chemical leaching[17]
Biodegradability / compostabilityNot biodegradable[17]Not biodegradable[17]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[17]Mechanically recyclable but not accepted in household plastic collection[17]
Electrical & ESD propertiesSurface resistance above 10⁹ ohm/sq — not static-dissipative (ASTM D257)[1]Not documented
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[26][14]High — hazardous VOC such as styrene; enclosure and filtration needed[26][14]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[26]12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[26]
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[26]2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[26]
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[26][14]Styrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[26][14]
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[26][14]Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[26][14]
Dust & fibre handling hazardCarbon fibre is bound in the matrix; sanding dust should not be inhaled[1]Not documented
Post-Processing
Sanding & machiningSands well and takes filler before painting[17]Sands well and takes filler before painting[17]
Painting & finishingPaints readily after light abrasion[17]Paints readily after light abrasion[17]
Vapour / chemical smoothingAcetone smoothing is blunted by the fibre — only the resin fraction dissolves[4]Acetone vapour smoothing works[4]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[27][14]HIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[27][14]
Solvents & Solubility
Soluble inAcetone dissolves the resin and leaves the fibre as sludge; MEK, THF, ethyl acetate and chlorinated solvents do the same.[28][4]Acetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[28][4]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[28][29]Petrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[28][29]
Solvent welding & smoothing agentAcetone vapour reaches only the resin fraction, so the fibre is left standing proud of the smoothed surface.[30][4]Acetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[30]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. CarbonX Carbon Fiber ABS Technical Data Sheet 3DXTech · 2026-08 · tds
  2. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  3. Polymaker ABS Max Technical Data Sheet V1.1 (2026-06-01) Polymaker · 2026-06 · tds
  4. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  5. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  6. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  7. IEMAI CF-ABS 3D Printing Filament product page IEMAI 3D · 2026-08 · vendor
  8. Siraya Tech Fibreheart ABS-CF Filament product page Siraya Tech · 2026-08 · vendor
  9. YXPOLYER ABS CF product page YXPOLYER · 2026-08 · vendor
  10. Polymaker product catalogue Polymaker · 2026-08 · vendor
  11. Siraya Tech Fibreheart ABS-CF Core Filament product page Siraya Tech · 2026-08 · vendor
  12. SUNLU E-ABS (Easy ABS) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  13. YXPOLYER ABS Enhanced product page YXPOLYER · 2026-08 · vendor
  14. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  15. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  16. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  17. ABS — material basics Polymaker Wiki · 2026-08 · doc
  18. CARBONX ABS+CF — product page (print recommendations) 3DXTech · 2026-08 · doc
  19. Composite materials filled with carbon, kevlar or glass Prusa Knowledge Base · 2026-08 · doc
  20. Carbon Fiber Filled — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  21. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  22. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  23. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  24. Effects of Fiber Orientation on the Coefficient of Thermal Expansion of Fiber-Filled Polymer Systems in Large Format Polymer Extrusion-Based Additive Manufacturing Materials 15(8):2764 · 2022-04 · paper
  25. Characterization of Thermal Expansion Coefficient of 3D Printing Polymeric Materials Using Fiber Bragg Grating Sensors Materials 17(18):4668 · 2024-09 · paper
  26. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  27. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  28. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  29. HIPS — Knowledge Base Prusa Research · 2026-08 · doc
  30. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc