3D Printing InfoPrinter comparison
LulzBot TAZ Pro vs Sovol Zero
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore LulzBot TAZ Pro comparisonsMore Sovol Zero comparisons
| Property | LulzBot TAZ ProBEDSLINGER | Sovol ZeroCOREXY |
|---|---|---|
| Identity | ||
| Brand | LulzBot | Sovol |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | LulzBot TAZ Pro (LulzBot's own store lists it under Legacy LulzBot printers)[1] | Sovol Zero 3D Printer[2][3] |
| Street price (USD; dated snapshot per entry) | $4,950.00 on buy.lulzbot.com, in stock, checked Aug 2026[1] | $389.00 on sovol3d.com against a $499.00 compare-at price, but marked Sold out, checked Aug 2026. Sovol's own announcement article quotes from $359.00[2][3][4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Several TAZ Pro derivatives exist and their specs differ substantially: TAZ Pro S, TAZ Pro XT+, and TAZ Pro Long Bed (282 x 582 x 285 mm, 1.2 mm GammaMaster steel nozzle, 80 °C bed cap, 150 mm/s travel, BLTouch 32-point mesh). The base TAZ Pro is 285 mm cubed with a 0.5 mm hardened-steel nozzle, a 110 °C bed and 300 mm/s travel — do not mix the two spec sets[1][5] | No sibling variants at the time of checking. Sovol positions it against the Voron 0 and Bambu Lab P1P. Note the bed and nozzle limits are higher than the larger SV08 (120 vs 100 °C bed, 350 vs 300 °C nozzle), so SV08 figures must not be carried across[2][4][6] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 285 x 285 x 285 mm[1] | 152.4 x 152.4 x 152.5 mm advertised[2][4] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | Not documented | 345 x 420 x 475 mm[2] |
| Frame construction & material | Open frame; movement on GT2 belts with Igus SST rods and polymer bushings[1] | Full linear rails on all axes; CoreXY with two motors sharing the moving mass[4] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed[4] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | CoreXY[4] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Not documented | Linear rails on all axes[4] |
| Belts (type, width, e.g. Gates?) | GT2 belt drive[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Trinamic TMC2130[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | Not documented | 1200 mm/s maximum (manufacturer claim). Sovol's own material acknowledges 700 mm/s as the realistic figure for detailed prints[2][4] |
| Max travel speed | 300 mm/s maximum travel speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | Not documented | 40,000 mm/s2 maximum (manufacturer claim)[2][4] |
| Max volumetric flow claimed (mm³/s) | Not documented | <=50 mm3/s (manufacturer claim)[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Pro Dual Extruder tool head — two active-lifting hot ends for true dual-material printing[1] | Planetary-gear direct-drive extruder[2] |
| Filament diameter | 2.85 mm standard, 1.75 mm optional[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Ceramic heating plate. Brass or hardened-steel nozzles in 0.2/0.4/0.6/0.8/1.0 mm[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 290 °C maximum hot end temperature[1] | <=350 °C claimed[2][4] |
| Stock nozzle size & sizes included in box | 0.5 mm hardened steel[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Hardened steel[1] | Brass or hardened steel, buyer's choice[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 °C maximum bed temperature[1] | <=120 °C claimed; Sovol states the bed is AC-heated[2][4] |
| Bed heater type (DC/AC mains) & wattage | 360 W, 24 V silicone bed heater[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Dual-sided borosilicate glass with PEI film[1] | Double-sided PEI steel plate[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 4-point mesh levelling using a 5 V contact circuit, plus automatic X-axis tramming, Z-offset and backlash compensation[1] | Eddy-current scanning combined with pressure (force) sensing — Sovol describes it as an inductive sensor plus force sensor[2][4] |
| Mesh grid size (probe point count — firmware evidence) | 4-point mesh[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament sensor with both runout and stripping detection[1] | Filament sensor fitted; type and location not published[2][4] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[1] | Not documented |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | Allwinner H616, 1 GB RAM, 8 GB eMMC, 64-bit[2] |
| PSU (brand, wattage, rail voltage) | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[1] | 150 W / 24 V (this is the DC supply; the bed is separately AC-heated per Sovol)[2][4] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Marlin[1] | Not named on the product page beyond OTA updates and OrcaSlicer support; Sovol markets the machine as open source[2][4] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch full-colour resistive touchscreen[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB serial; a 16 GB flash drive is included for standalone printing[1] | Ethernet and Wi-Fi 2.4 GHz, WPA2 only (WPA3 not supported)[2][4] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Built-in camera for monitoring; resolution not published[2][4] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Arrives preassembled[4] |
| Power-Loss & Interruption Recovery | ||
| Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?) | Not documented | Power-loss recovery supported; mechanism not published[2][4] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[1] | PLA, PETG, TPU, PETG-CF, ABS, ASA, PA, PC[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | FCC, CE, RCM, ETL, CSA, OSHWA and WEEE. The OSHWA listing is the open-hardware certification[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 1 year standard, with extended options. Made in the USA[1] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- Sovol Zero 3D Printer product page sovol3d.com · 2026-08 · vendor
- Sovol 3D-printer collection product feed (live prices and stock) sovol3d.com · 2026-08 · vendor
- Sovol Zero announcement article (Sovol blog) sovol3d.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- Sovol SV08 3D Printer product page sovol3d.com · 2026-08 · vendor