3D Printing InfoPrinter comparison
LulzBot TAZ Pro Long Bed vs UltiMaker Factor 4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore LulzBot TAZ Pro Long Bed comparisonsMore UltiMaker Factor 4 comparisons
| Property | LulzBot TAZ Pro Long BedBEDSLINGER | UltiMaker Factor 4INDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | LulzBot | UltiMaker |
| Class | BEDSLINGER | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | LulzBot TAZ Pro Long Bed 3D Printer[1] | UltiMaker Factor 4[2] |
| Release date (announcement and actual shipping) | Not documented | Announced 22 April 2024, shown at HANNOVER MESSE 2024 (22-26 April) and TCT Asia (7-9 May 2024)[2] |
| Launch MSRP (USD) | Not documented | Starting at approximately $20,000[2] |
| Street price (USD; dated snapshot per entry) | $7,995.00 at MatterHackers, listed as currently unavailable, checked Aug 2026[1] | Not documented |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Not simply a longer TAZ Pro. The Long Bed ships the Asteroid 285 tool head with a 1.2 mm nozzle, a 0.3-0.9 mm equipped layer range, an 80 °C bed cap (vs 110 °C), 150 mm/s travel (vs 300) and BLTouch 32-point mesh levelling (vs 4-point contact). Bed material also differs: blue spring-steel magnetic flex rather than glass with PEI film[1][3] | Shares the 330 x 240 x 300 mm envelope with the UltiMaker S5, S7 and S8, which is the single most contaminated figure in UltiMaker's range. What separates the Factor 4 is the actively controlled 70 °C build volume, the climate-controlled 6-spool material station holding humidity below 15%, and HEPA filtration. UltiMaker also sells a Factor 4 Plus[2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 282 x 582 x 285 mm[1] | 330 x 240 x 300 mm[2] |
| Frame construction & material | Open frame; GT2 belt drive with Igus SST rods and polymer bushings[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosed with actively controlled chamber airflow and a HEPA filter[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Build volume temperature controlled up to 70 °C with actively controlled chamber airflow (manufacturer specification)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | Direct-drive dual extrusion; kinematic layout not stated in the source checked[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Trinamic TMC2130[1] | Not documented |
| Speed & Acceleration | ||
| Max travel speed | 150 mm/s maximum travel speed, firmware-limited[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Asteroid 285 tool head[1] | Direct-drive dual extrusion[2] |
| Filament diameter | 2.85 mm standard, 1.75 mm optional[1] | 2.85 mm[2] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | 290 °C maximum, firmware-limited[1] | 340 °C maximum with the high-temperature print core (manufacturer claim)[2] |
| Stock nozzle size & sizes included in box | 1.2 mm GammaMaster steel[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | GammaMaster steel[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 80 °C maximum bed temperature — notably lower than the base TAZ Pro[1] | Not documented |
| Bed heater type (DC/AC mains) & wattage | 360 W, 24 V silicone bed heater[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Blue spring-steel magnetic flex bed system[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | BLTouch, 32-point automatic mesh calibration[1] | Not documented |
| Mesh grid size (probe point count — firmware evidence) | 32 points[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament sensor with runout and stripping detection[1] | Not documented |
| Spool holder location & max spool size; drybox compatibility | Not documented | Automatic climate-controlled material handling and storage station holding humidity below 15%, storing up to six spools[2] |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | HEPA filter[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[1] | Not documented |
| PSU (brand, wattage, rail voltage) | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Marlin[1] | Not documented |
| Connectivity, UI & Camera | ||
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB serial; 16 GB flash drive included for standalone printing[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[1] | UltiMaker-branded PPS CF, PLA, Tough PLA, Nylon, PETG, PET CF and PVA, plus validated third-party materials from BASF Forward AM, Kimya, Polymaker, LEHVOSS and Jabil[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 1 year standard with extended options. Made in the USA[1] | Not documented |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification)[1] | Dimensional accuracy within +/-0.2 mm or +/-0.2% of feature nominal length; UltiMaker states it tested over 95% print-completion success. Manufacturer figures, not independent measurements[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- UltiMaker Factor 4: technical specifications and pricing 3dprintingindustry.com · 2026-08 · review
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor