3D Printing InfoPrinter comparison
FlashForge Creator 4 vs LulzBot TAZ Pro Long Bed
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore FlashForge Creator 4 comparisonsMore LulzBot TAZ Pro Long Bed comparisons
| Property | FlashForge Creator 4IDEX | LulzBot TAZ Pro Long BedBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | FlashForge | LulzBot |
| Class | IDEX | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Flashforge Creator 4, sold in A and S configurations (Creator 4A, Creator 4S)[1] | LulzBot TAZ Pro Long Bed 3D Printer[2] |
| Street price (USD; dated snapshot per entry) | $10,999.00 at Top 3D Shop with a 2-3 week lead time, checked Aug 2026[1] | $7,995.00 at MatterHackers, listed as currently unavailable, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two factory configurations that share the chassis but not the temperature ceiling: Creator 4A ships 2 x HT extruders (320 °C max, no composite support), Creator 4S ships 1 x HT + 1 x HS (360 °C max, supports PA-CF, PA-GF, PP-CF, PPS-CF). A third extruder type, F, is rated 265 °C and intended for flexibles. Any published "360 °C" figure applies only to the HS head[1] | Not simply a longer TAZ Pro. The Long Bed ships the Asteroid 285 tool head with a 1.2 mm nozzle, a 0.3-0.9 mm equipped layer range, an 80 °C bed cap (vs 110 °C), 150 mm/s travel (vs 300) and BLTouch 32-point mesh levelling (vs 4-point contact). Bed material also differs: blue spring-steel magnetic flex rather than glass with PEI film[2][3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 400 x 350 x 500 mm[1] | 282 x 582 x 285 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 840 x 675 x 1000 mm (1050 mm on the stand). FlashForge specifies an installation space of at least 1400 x 1500 x 1600 mm[1] | Not documented |
| Net weight (kg) | 90 kg net[1] | Not documented |
| Frame construction & material | Fully enclosed professional chassis on a stand[1] | Open frame; GT2 belt drive with Igus SST rods and polymer bushings[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with HEPA 13 filtration and an actively controlled chamber[1] | Open frame, no enclosure[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Up to 65 °C, actively controlled (manufacturer claim)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | IDEX — two independently driven extruders on the same gantry[1] | Cartesian bedslinger[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic TMC2130[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 10-200 mm/s, adjustable per material. On the 4S the HS head is quoted 100-150 mm/s and the HT head 100-200 mm/s (manufacturer figures)[1] | Not documented |
| Max travel speed | Not documented | 150 mm/s maximum travel speed, firmware-limited[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive, two independent extruders, interchangeable modules (F / HT / HS)[1] | Asteroid 285 tool head[2] |
| Filament diameter | Not documented | 2.85 mm standard, 1.75 mm optional[2] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | Depends on the fitted extruder module: F 265 °C, HT 320 °C, HS 360 °C[1] | 290 °C maximum, firmware-limited[2] |
| Stock nozzle size & sizes included in box | 0.4 mm default; 0.6 and 0.8 mm optional[1] | 1.2 mm GammaMaster steel[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | GammaMaster steel[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 130 °C maximum (manufacturer claim)[1] | 80 °C maximum bed temperature — notably lower than the base TAZ Pro[2] |
| Bed heater type (DC/AC mains) & wattage | Not documented | 360 W, 24 V silicone bed heater[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Blue spring-steel magnetic flex bed system[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic bed levelling; FlashForge does not name the probe technology in this spec table[1] | BLTouch, 32-point automatic mesh calibration[2] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 32 points[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament sensor with runout and stripping detection[2] |
| Spool holder location & max spool size; drybox compatibility | Two spool bays, 1 kg and 2 kg capacity[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[2] |
| Input voltage (110/220 V, switch or auto) | AC 100-130 V / 200-240 V, 50-60 Hz, 30 A overcurrent protection[1] | Not documented |
| Total rated power draw | 2320 W rated[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not named; the supported slicer is FlashPrint[1] | Marlin[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 7-inch touchscreen, 1024 x 600[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB flash drive, Ethernet, Wi-Fi[1] | USB serial; 16 GB flash drive included for standalone printing[2] |
| Materials Support | ||
| Officially supported filament list | Standard and engineering plastics on the HT head; the HS head adds PA-CF, PA-GF, PP-CF and PPS-CF. Materials such as PC, PA and carbon fibre are the stated targets for the 130 °C bed[1] | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on the printer, 3 months on extruder parts[1] | 1 year standard with extended options. Made in the USA[2] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Flashforge Creator 4 (A/S) product listing with full spec table top3dshop.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor