3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Voron 0.2
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Voron 0.2 comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Voron 0.2COREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Voron Design |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Voron 0.2, current revision R1. Sold under kit vendors' names: "Voron V0.2-S1 (R1) 3D Printer Kit by LDO & HoneyBadger", "Voron 0.2 R1 Latest Version CoreXY 3D Printer Kit" (Formbot)[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][6][5] | There is no single price: Voron is an open design and kits come from several vendors. Formbot's kit is $328.06 (was $349.00, 6% off), in stock, checked Aug 2026. The LDO & HoneyBadger V0.2-S1 kit is $639.99 but sold out. Neither figure includes printed parts unless the option is selected[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][7][8][9] | Two things get conflated. First, revision: R1 is the current one, adding a filament-runout sensor, MR85 bearings and fastener changes. Second, kit vendor: the LDO/HoneyBadger S1 kit ships an SKR Pico, E3D Revo, HoneyBadger dual-sided PEI/CF bed and 200 W supply, while the Formbot kit ships a TZ V6 or Dragon hotend and a 150 W supply, so hotend and PSU specs are vendor-specific, not model-specific. Printed parts are an extra on both[2][3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 120 x 120 x 120 mm[2][3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | Not documented |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[7] | Aluminium-extrusion CoreXY frame with acrylic panels (LDO kit); the LDO/HoneyBadger build uses a 100 mm top hat. X axis on a genuine HIWIN rail, Y and Z on HoneyBadger stainless rails[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Enclosed by acrylic panels in the LDO kit[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY with the build plate moving in Z[2][3] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Not documented | Genuine HIWIN linear rail on X in the LDO kit[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | 250 mm/s max print speed, 300 mm/s max travel (Formbot kit listing). This is a kit-vendor figure, not a Voron Design specification[3] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][9] | Direct drive in a Mini Stealthburner toolhead with a picobilical board and umbilical cable (LDO kit)[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Kit-dependent: E3D Revo (Voron edition) in the LDO kit; TZ V6, Dragon standard-flow or Dragon high-flow in the Formbot kit[2][3] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 °C on the Formbot kit listing. The LDO kit's E3D Revo has its own limit, not stated on the listing[3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 110 °C (Formbot kit listing)[3] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | HoneyBadger dual-sided P-series plate in the LDO kit: smooth black PEI on one face, carbon fibre on the other, on a Kirigami mount with an edge-to-edge polyimide film heater[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Kit-dependent. LDO kit: SKR Pico (LDO Edition) with a Raspberry Pi 4B as host[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 200 W (LDO kit) or 150 W (Formbot kit)[2][3] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][9] | Klipper[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Not documented |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Self-assembly kit. Printed parts are not included in the LDO kit (sourced separately, e.g. through Voron's Print It Forward); the Formbot kit offers them as an option[2][3] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[10] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Voron V0.2-S1 (R1) kit by LDO & HoneyBadger fabreeko.com · 2026-08 · vendor
- Voron 0.2 R1 CoreXY kit (Formbot) formbot3d.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor