3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs Sovol SV06 Plus
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore Sovol SV06 Plus comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | Sovol SV06 PlusBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | Sovol |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Sovol SV06 Plus[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][5][4] | Not documented |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][6][7][8] | Larger sibling of the SV06 (220x220x250). Distinct from the SV06 Plus ACE, which is 300x300x350 mm, runs Klipper on an RK3308, adds a 4.3-inch touchscreen, camera and ceramic hotend. The 340 mm vs 350 mm Z figure is the cleanest way to tell the two apart in a spec box[2][9] |
| Market position: superseded? successor announced? | Not documented | Delisted by Sovol; the current collection carries the SV06 Plus ACE instead. 3DJake shows it sold out and no longer stocked[10][2] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 300 x 300 x 340 mm advertised (note: the ACE version is 350 mm in Z)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | Not documented |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[6] | Open frame with linear-rail motion, supplied as an assembly kit. One 3DJake purchaser reports construction defects and linear-axis stability problems[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Cartesian i3 bedslinger[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][8] | Direct-drive extruder, single[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Not documented |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][8] | Not documented |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | USB connection and mini-SD card[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | 1.75 mm filament; no per-material list published on the listing[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[11] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Sovol SV06 Plus technical data table 3djake.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Sovol SV06 Plus ACE 3D Printer product page sovol3d.com · 2026-08 · vendor
- Sovol 3D-printer collection product feed (live prices and stock) sovol3d.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor