3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs LulzBot TAZ Pro
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore LulzBot TAZ Pro comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | LulzBot TAZ ProBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | LulzBot |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | LulzBot TAZ Pro (LulzBot's own store lists it under Legacy LulzBot printers)[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][5][4] | $4,950.00 on buy.lulzbot.com, in stock, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][6][7][8] | Several TAZ Pro derivatives exist and their specs differ substantially: TAZ Pro S, TAZ Pro XT+, and TAZ Pro Long Bed (282 x 582 x 285 mm, 1.2 mm GammaMaster steel nozzle, 80 °C bed cap, 150 mm/s travel, BLTouch 32-point mesh). The base TAZ Pro is 285 mm cubed with a 0.5 mm hardened-steel nozzle, a 110 °C bed and 300 mm/s travel — do not mix the two spec sets[2][9] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 285 x 285 x 285 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | Not documented |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[6] | Open frame; movement on GT2 belts with Igus SST rods and polymer bushings[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Cartesian bedslinger[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Belts (type, width, e.g. Gates?) | Not documented | GT2 belt drive[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Trinamic TMC2130[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | Not documented |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max travel speed | Not documented | 300 mm/s maximum travel speed (manufacturer figure)[2] |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][8] | Pro Dual Extruder tool head — two active-lifting hot ends for true dual-material printing[2] |
| Filament diameter | Not documented | 2.85 mm standard, 1.75 mm optional[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 290 °C maximum hot end temperature[2] |
| Stock nozzle size & sizes included in box | Not documented | 0.5 mm hardened steel[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 110 °C maximum bed temperature[2] |
| Bed heater type (DC/AC mains) & wattage | Not documented | 360 W, 24 V silicone bed heater[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Dual-sided borosilicate glass with PEI film[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Automatic 4-point mesh levelling using a 5 V contact circuit, plus automatic X-axis tramming, Z-offset and backlash compensation[2] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 4-point mesh[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Filament sensor with both runout and stripping detection[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[2] |
| PSU (brand, wattage, rail voltage) | Not documented | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[2] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][8] | Marlin[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 5-inch full-colour resistive touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | USB serial; a 16 GB flash drive is included for standalone printing[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[2] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | Not documented | FCC, CE, RCM, ETL, CSA, OSHWA and WEEE. The OSHWA listing is the open-hardware certification[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[10] | 1 year standard, with extended options. Made in the USA[2] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Not documented | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification, not an independent measurement)[2] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor