3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs FlashForge AD5X
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore FlashForge AD5X comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | FlashForge AD5XCOREXY |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | FlashForge |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | Flashforge AD5X, sold as "AD5X - Multicolor 3D Printer for High-Speed, Full-Color Printing"[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][6][5] | $399.00 sale against a $549.00 compare-at price on flashforge.com, in stock, with a further $50 off at checkout, checked Aug 2026. A refurbished AD5X is listed at $315.00[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][7][8][9] | Shares the 220 mm Adventurer chassis with the 5M and 5M Pro but differs on the points that matter: 300 °C nozzle (vs 280 °C), 4-colour IFS unit, NO air filtration, NO auto shutdown, and a 300 mm/s print speed against a 600 mm/s travel speed. 3DJake and eolasprints both describe it as open-frame[2][10][11][12] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 220 x 220 x 220 mm advertised[2][10] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | Not documented |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | Not documented |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[7] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame, no enclosure and no air filtration — FlashForge's own table records "Air Filtration: No". Chamber lighting and remote monitoring are listed as expandable options rather than fitted[2][11] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | CoreXY[11] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | FlashForge publishes two separate figures: max travel speed 600 mm/s and max print speed 300 mm/s. The 300 mm/s print figure is the one that describes printing[2][10] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | 20,000 mm/s2 maximum (manufacturer claim)[2][10] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][9] | Direct drive, one extruder, fed by the 4-colour Intelligent Filament System (IFS)[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 °C claimed[2][10] |
| Stock nozzle size & sizes included in box | Not documented | 0.4 mm default; 0.25, 0.6 and 0.8 mm optional[2][10] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 110 °C claimed[2][10] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | PEI flexible spring-steel sheet[2][10] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Automatic levelling; probe technology not named[2][10] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Filament detection fitted; type and location not published[2][10] |
| Multi-material/multi-color capability or official upgrade path | Not documented | Four-colour printing via the integrated Intelligent Filament System (IFS), which handles filament switching[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | Not documented |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][9] | Not named by FlashForge; the supported slicers are Orca-Flashforge and OrcaSlicer[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | USB, Ethernet, Wi-Fi[2][10] |
| Power-Loss & Interruption Recovery | ||
| Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?) | Not documented | Power-outage recovery supported; mechanism not published[2][10] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | PETG, PLA, TPU95A, TPU64D-75D, PLA-CF, PETG-CF[2][10] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[13] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- Flashforge AD5X multicolour 3D printer product page flashforge.com · 2026-08 · vendor
- Flashforge store product feed (live prices and stock) flashforge.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- FlashForge AD5X technical data table 3djake.com · 2026-08 · vendor
- Flashforge printer buyer's guide, 5M to Creator 5 eolasprints.com · 2026-08 · review
- Flashforge Adventurer 5M Pro product page flashforge.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor