3D Printing InfoPrinter comparison
ELEGOO Neptune 4 Plus vs ELEGOO OrangeStorm Giga
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Neptune 4 Plus comparisonsMore ELEGOO OrangeStorm Giga comparisons
| Property | ELEGOO Neptune 4 PlusBEDSLINGER | ELEGOO OrangeStorm GigaINDUSTRIAL |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | ELEGOO |
| Class | BEDSLINGER | INDUSTRIAL |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Neptune 4 Plus[1] | ELEGOO OrangeStorm Giga[2] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[3][4] | Listed on the ELEGOO US store from 17 October 2024 (Shopify publish date)[5] |
| Street price (USD; dated snapshot per entry) | $309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[3][6][4] | $2,499.00 on us.elegoo.com, Aug 2026, against a compare-at price of $3,125.00[5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[1][7][8][9] | Sold bare and in bundles; dual-printhead and quad-printhead upgrade kits are separate products, so a Giga's nozzle count depends on which kit was bought. The four printheads sit on the same X axis and print four copies of the same model in parallel (or the same model in four colours) - this is not an IDEX or a toolchanger[2][10] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 320 x 320 x 385 mm; printing platform 330 x 330 mm[1] | 800 x 800 x 1000 mm; the platform is 820 x 820 mm made up of four independent 410 x 410 mm PEI plates[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[1] | 1224 x 1164 x 1425 mm; ELEGOO's maximum size for machine activity is 1224 x 1520 x 1570 mm. This is a floor-standing machine, not a desktop one[2] |
| Net weight (kg) | 14.4 kg net, 16.65 kg gross[1] | 104 kg net, 145 kg gross, and it ships in multiple crates (bottom + XY axis components, then two Z-axis components)[2] |
| Frame construction & material | CNC-machined aluminium extrusion frame (Neptune 4 family)[7] | CNC-machined aluminium extrusion frame; the X and Y axes run on linear guides and the machine sits on carbon steel round bases with rubber anti-slip pads[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian i3 bed-slinger[1] | Cartesian gantry with a fixed bed - the printhead moves in X and Y on linear guides and the gantry moves in Z, so nothing about the bed moves during a print[2] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Not documented | Linear guide on the X axis[2] |
| Y-axis guide type | Not documented | Linear guide on the Y axis[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Two lead screws with two tie rods[1] | Four lead screws with four linear guide rods[11] |
| Belts (type, width, e.g. Gates?) | Not documented | X/Y belts with knob-adjustable tensioners[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[1] | "Silent Drive (All Axes)"; no driver part number published[11] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[1] | 30-300 mm/s, with 150 mm/s given by ELEGOO as the recommended speed - far below the 500-600 mm/s claimed for desktop machines, which is the honest consequence of moving a gantry this size[2][11] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | 150 mm/s recommended printing speed (manufacturer figure)[11] |
| Max acceleration (claimed, mm/s²) | 12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[1] | 5000 mm/s2 maximum acceleration, which is also the default - four times lower than the Centauri machines[11] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[1][9] | Dual-gear direct extruder with 2 fans[11] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[1] | Brass nozzle - and note the standard diameter here is 0.6 mm, not the 0.4 mm used across the rest of the ELEGOO range[11] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 100 C max heated bed temperature at 25 C ambient[1] | 100 C max heated bed temperature at 25 C ambient, across four independent 410 x 410 mm PEI magnetic high-temperature platforms[2] |
| Bed surface (material, texture, coating), single/double-sided | PEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[1] | Four independent 410 x 410 mm PEI magnetic platforms rather than one large plate[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Manual levelling combined with 121-point auto-levelling[1] | Manual levelling combined with 100-point auto-levelling (the desktop ELEGOO machines use a 121-point mesh)[11][9] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[1] | Filament detection and power-loss resume printing[2] |
| Multi-material/multi-color capability or official upgrade path | Not documented | Up to three additional printheads can be added on the X axis for four-nozzle simultaneous printing - four copies of one model at once, or the same model in four colours[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | ELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[1] | "Klipper High-Speed Quiet Motherboard" is all ELEGOO publishes[11] |
| Total rated power draw | 320 W rated power; 24 V output; 110-120 V / 220-240 V input[1] | 1530 W with a single head, plus 100 W per additional head, to a stated maximum of 1830 W with four nozzles; 100-120 VAC / 220-240 VAC, 50/60 Hz[2][11] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[1][9] | Klipper[11] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour capacitive touch screen[1] | 10.1-inch colour capacitive touch screen - by far the largest in the ELEGOO range[11] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[1] | Colour capacitive touch UI; ElegooSlicer recommended, Orca and Cura supported[11] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB, LAN and Wi-Fi[1] | Wi-Fi, USB and LAN file transfer[2] |
| Materials Support | ||
| Officially supported filament list | PLA, TPU, PETG, ABS, ASA, Nylon[1] | The product page lists PLA, PETG and TPU; ELEGOO's compare page adds Nylon to the same machine. Either way it is a much shorter list than the Neptune bed-slingers[2][11] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO OrangeStorm Giga product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO OrangeStorm Giga Shopify product JSON (price and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor