3D Printing InfoPrinter comparison
ELEGOO Centauri Carbon 2 Combo vs FlashForge Creator 5 Pro
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore ELEGOO Centauri Carbon 2 Combo comparisonsMore FlashForge Creator 5 Pro comparisons
| Property | ELEGOO Centauri Carbon 2 ComboCOREXY | FlashForge Creator 5 ProTOOLCHANGER |
|---|---|---|
| Identity | ||
| Brand | ELEGOO | FlashForge |
| Class | COREXY | TOOLCHANGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | ELEGOO Centauri Carbon 2 Combo[1] | Flashforge Creator 5 Pro, sold as "Creator 5 Pro 4-Toolheads Enclosed Multi-Color 3D Printer"[2][3] |
| Release date (announcement and actual shipping) | Listed on the ELEGOO US store from 9 August 2026 (Shopify publish date)[4] | Launched alongside the Creator 5; one secondary source gives an estimated early-Q3 2026 release for the Pro specifically, while the joint launch report of 19 May 2026 covers both[5][6] |
| Launch MSRP (USD) | Not documented | $799 early-bird (deposit price, open until 20 June 2026); $949 standard MSRP[5][6] |
| Street price (USD; dated snapshot per entry) | $399.00 on us.elegoo.com, Aug 2026, against a compare-at price of $449.00[4] | $949.00 on flashforge.com, in stock, with $100 auto-applied in cart, checked Aug 2026[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | The Centauri Carbon 2 sold with the CANVAS multicolour unit. Every printing figure matches the bare Centauri Carbon 2; what changes is the body - 500 x 480 x 743 mm and 19.35 kg with CANVAS fitted - and CANVAS capability being listed Yes. Against the first-generation Centauri Carbon: 350 C nozzle rather than 320 C, clog detection added, and a HEPA plus coconut-shell carbon filter stack rather than the nano mineral crystal filter. An ELEGOO x emoji collaboration edition of the same machine is also listed[1][7][8][9] | Enclosed version of the Creator 5. The $150 difference buys the enclosure, 65 °C active chamber heating, air filtration and engineering-material support. Build volume, toolhead count, speed and acceleration are identical to the Creator 5[2][5][6] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm; printing platform 260 x 260 mm[1] | 256 x 256 x 256 mm[5][6][10] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 500 x 480 x 743 mm with the CANVAS unit fitted[1] | Not documented |
| Net weight (kg) | 19.35 kg net, 23.8 kg gross[1] | Not documented |
| Frame construction & material | Integrated die-cast aluminium construction (Centauri Carbon platform)[8] | Rigid frame with a fully sealed enclosure; no dimensions or weight published[2][6] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed; the Centauri Carbon 2 uses a HEPA plus granulated coconut-shell activated-carbon filter stack rather than the first generation's nano mineral crystal filter, and adds a smart exhaust grille[7][8] | Fully enclosed with door and top cover, with continuous airflow and dual-layer H13 HEPA plus coconut-shell activated carbon filtration[2][5][6] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Up to 65 °C, actively heated with adaptive circulation (manufacturer claim — a heater setpoint, not a measured passive figure)[2][5][6] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY[1] | CoreXY with four independent FlashSwap toolheads[5][6] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Three lead screws with three linear guide rods[1] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | "Silent Drive (All Axes)"; no driver part number published[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s or less, with 250 mm/s given as the recommended speed[1] | 600 mm/s maximum (manufacturer claim)[2][5][6] |
| Recommended/typical print speed | 250 mm/s recommended printing speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 maximum acceleration; default 10000 mm/s2[1] | 30,000 mm/s2 maximum (manufacturer claim)[5][6] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual-gear direct extruder with one fan[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Brass-hardened steel nozzle, 0.4 mm, titanium-alloy heat break[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 350 C claimed max nozzle temperature - 30 C above the first-generation Centauri Carbon[1][8] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel nozzles as standard[5][6] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heated bed temperature at 25 C ambient[1] | 120 °C maximum (manufacturer claim)[6] |
| Bed surface (material, texture, coating), single/double-sided | Dual-sided spring steel sheet, textured PEI plus a PLA-specific surface[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | 121-point auto-levelling with full-auto calibration[1] | Fully automatic calibration and levelling; probe technology not named[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor, clog detection, auto filament unloading and power-loss recovery[1] | Not documented |
| Multi-material/multi-color capability or official upgrade path | CANVAS multi-material capability included - the defining difference from the bare Centauri Carbon 2[1] | Four independent toolheads, physically swapped; FlashForge markets zero purge waste[2][5] |
| Cooling & Air Handling | ||
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | Not documented | H13 HEPA plus coconut-shell activated carbon, dual layer, with continuous airflow[2][5][6] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | "Powerful Self-Developed Motherboard" is all ELEGOO publishes[1] | Not documented |
| Total rated power draw | 1100 W at 220 V, 350 W at 110 V rated; 24 V output[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | ELEGOO OS; ElegooSlicer recommended, Orca and Cura supported[1] | Not named by FlashForge. Supported slicers are Flash Studio, Orca-Flashforge and OrcaSlicer[6] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch colour capacitive touch screen (the first-generation Centauri Carbon used a 4.3-inch panel)[1][8] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Colour touch UI; LED lighting fitted; STL, OBJ, 3MF and STEP input[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | USB and Wi-Fi[1] | Dual-band Wi-Fi 2.4 GHz + 5 GHz, LAN, USB[5][6] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Camera fitted[1] | 1080p camera at 30 fps[5][6] |
| Materials Support | ||
| Officially supported filament list | Ideal: PLA, PETG, ABS, ASA. Capable: TPU, PC, PA, PET and fibre-reinforced filaments[1] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Operating sound published as 45 dB or less - a manufacturer figure with no distance or method stated, and 10 dB below the first-generation Centauri Carbon's published figure[1][8] | 55 dB claimed by the manufacturer. No independent measurement found; distance and method not stated[5] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[11] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 Pro 4-Toolheads product page flashforge.com · 2026-08 · vendor
- Flashforge store search results for Creator 5 (live prices) flashforge.com · 2026-08 · vendor
- ELEGOO Centauri Carbon 2 Combo Shopify product JSON (price and store publish date) us.elegoo.com · 2026-08 · vendor
- Flashforge Creator 5 and Creator 5 Pro launch report 3dprinting.com · 2026-08 · review
- Flashforge Creator 5 and 5 Pro breakdown antonmansson.com · 2026-08 · review
- ELEGOO Centauri Carbon 2 product page (Centauri Carbon 2 vs Centauri Carbon side-by-side table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO US store 3D printers collection (current line-up, Aug 2026) us.elegoo.com · 2026-08 · vendor
- Flashforge printer buyer's guide, 5M to Creator 5 eolasprints.com · 2026-08 · review
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor