3D Printing InfoPrinter comparison
Bambu Lab X2D vs Voron Trident
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab X2D comparisonsMore Voron Trident comparisons
| Property | Bambu Lab X2DCOREXY | Voron TridentCOREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Voron Design |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab X2D; spec PDF header "X2D Spec"[1] | Voron Trident, current revision R2. Sold as "Voron Trident R2 3D Printer Kit by LDO"[2] |
| Street price (USD; dated snapshot per entry) | From $649.00 on the Bambu Lab US store, Aug 2026; the compare page shows the same $649 figure[3] | $1,274.99 for the LDO kit at Fabreeko, on pre-order with a mid-to-late September ship estimate, checked Aug 2026. Fabreeko's live product feed shows the Trident kit at $1,199.99 and unavailable, so the figure depends on which variant is selected[2][4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Dual-nozzle machine: a main hotend with a permanent-magnet synchronous extruder motor and an auxiliary hotend with a plain stepper motor, so the two nozzles are not equivalent. Bambu publishes four different build volumes depending on which nozzle is used, and a shorter list of materials for the auxiliary nozzle. Physical dimensions (392x406x478 mm) are shared with the P2S but the X2D is 16.25 kg against the P2S's 14.9 kg[1][5] | Two size variants on the LDO kit: Rev D 250 mm and Rev D+ 300 mm. Distinguished from the Voron 2.4 by the Z system: Trident has a fixed gantry with three Z motors lifting the bed, while the 2.4 lifts the gantry on four belted Z motors. Colour options black, space grey, blue[2][6] |
| Market position: superseded? successor announced? | Current model, launched into the slot vacated by the discontinued X1-Carbon[3] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | Main nozzle 256 x 256 x 260 mm; auxiliary nozzle 235.5 x 256 x 256 mm; dual-nozzle printing 235.5 x 256 x 256 mm; total volume for two nozzles 256 x 256 x 260 mm. The sortable figure below is the main-nozzle volume[1] | 250 x 250 x 250 mm or 300 x 300 x 300 mm depending on variant. Sortable value is the 300 mm kit[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | Not documented |
| Net weight (kg) | 16.25 kg net[1] | Not documented |
| Frame construction & material | Plastic and steel chassis; plastic, glass and metal outer frame[1] | Aluminium-extrusion CoreXY frame, self-assembly[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor, active chamber heating to 65 C, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack with an external exhaust fan[1] | Not documented |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Active chamber heating, maximum 65 C (manufacturer figure)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - not stated in the spec sheet; Bambu groups the X2D with its enclosed CoreXY machines and publishes the same 20000 mm/s2 acceleration figure[1] | CoreXY with a fixed gantry; three independent Z stepper motors raise the bed and perform bed levelling[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Three independent Z stepper motors under the bed[2] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | LDO Leviathan board: 5 x TMC2209 plus 2 x TMC5160 HV-capable drivers[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Two direct-drive extruders: main extruder with hardened-steel gears driven by a Bambu high-precision permanent-magnet synchronous motor, auxiliary extruder with hardened-steel gears driven by a stepper motor[1] | Bondtech Integrated Drive Gear Assembly (IGDA) with a Clockwork 2 motor[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Dual hardened-steel nozzles; 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; built-in filament cutter[1] | E3D Revo High Flow with a 60 W heater[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | Not documented |
| Heater cartridge power (W) | Not documented | 60 W (E3D Revo High Flow heater in the LDO kit)[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 120 C max heatbed temperature[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate, Textured PEI included; Smooth PEI, Cool Plate SuperTack and Engineering Plate supported[1] | LDO bed heater with a pre-installed magnet sheet and edge-to-edge heating[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | Omron inductive probe supplied; Klicky-mod parts also included in the kit[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1] | Not documented |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan, main control board fan, chamber heat-circulation fan, auxiliary part-cooling fan and external exhaust fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller dual-core Cortex-M4 plus single-core Cortex-M7; application processor quad-core ARM with a dedicated NPU (2 TOPS per the compare page)[1][7] | LDO Leviathan control board; Nitehawk SB USB toolhead board with an integrated accelerometer[2] |
| Total rated power draw | High-voltage version 1600 W at 220 V, low-voltage version 1100 W at 110 V; steady state 250 W printing PLA and 550 W printing PC at 25 C ambient[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[8] | Klipper[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 1280x720 touchscreen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n), built-in 8 GB eMMC and a USB port; Ethernet not available, no network kill switch, no 802.1X[1] | Not documented |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Two cameras: live-view 1920x1080 and a toolhead camera at 1600x1200[1] | Not documented |
| LED chamber/toolhead lighting | Not documented | COB LED chamber lighting included[2] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Self-assembly kit[2] |
| Materials Support | ||
| Officially supported filament list | Main hotend: PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA and carbon/glass-fibre reinforced PLA, PETG, ABS, ASA, PA6, PAHT, PPA, PET. Auxiliary hotend drops PPA-CF/GF and excludes PLA Aero; PLA Silk, PETG-CF, ASA-CF, PA6-CF, TPU for AMS and PA/PET support material are flagged "print with caution" on the auxiliary nozzle[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[9] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab X2D Spec (PDF) store.bblcdn.com · 2026-08 · doc
- Voron Trident R2 kit by LDO fabreeko.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Fabreeko Voron collection product feed (live prices) fabreeko.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Voron 2.4 R2 (Rev D+) kit by LDO fabreeko.com · 2026-08 · vendor
- Bambu Lab - Compare all 3D printers (A2L / X2D / H2C columns) bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor