3D Printing InfoPrinter comparison
Bambu Lab X1E vs Voron 2.4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab X1E comparisonsMore Voron 2.4 comparisons
| Property | Bambu Lab X1ECOREXY | Voron 2.4COREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Voron Design |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab X1E; spec PDF header "Bambu Lab X1E Technical Specification"[1] | Voron 2.4, current revision R2, kits shipping as Rev D and Rev D+. Sold as "Voron 2.4 R2 (Rev D+) 3D Printer Kit by LDO"[2][3] |
| Street price (USD; dated snapshot per entry) | Not documented | $1,399.99 for the LDO Rev D+ kit at Fabreeko (300 mm and 350 mm are the same price), on pre-order with a mid-September estimate, checked Aug 2026. Fabreeko's live feed shows the base 2.4 kit listing at $1,299.99 and available. 3DJake lists an LDO 350 RevD kit but will not ship to the US[2][4][5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Enterprise variant of the X1-Carbon, not a trim level. Differences from the X1C, from the two manufacturer spec sheets side by side: active chamber heating to 60 C (X1C has none), 320 C vs 300 C hot end, Smooth PEI plate included vs Cool/Engineering plates, G3+H12+carbon filter stack vs carbon filter only, Ethernet with a network kill switch, removable network module and 802.1X vs Wi-Fi only, 16 kg vs 14.13 kg, and 1400 W at 220 V / 750 W at 110 V vs 1000 W / 350 W[1][6] | Sizes 250, 300 and 350 mm; LDO ships Rev D and Rev D+. Colours black, space grey, blue. Do not confuse with the Trident: the 2.4 lifts the whole gantry on four belted Z motors, the Trident lifts the bed on three screws. The Rev D+ kit includes a Raspberry Pi 4B; the older 3DJake-listed RevD kit explicitly does not include a Pi[2][3][5][7] |
| Market position: superseded? successor announced? | Not present in the Bambu Lab US store 3D-printer collection in Aug 2026, which lists A1, A1 mini, A2L, P1S, P2S, X2D, H2S, H2D and H2C. Bambu sells business machines through a separate Business & Institution channel, so absence from the consumer collection is not proof of discontinuation; no live first-party price could be recorded[8] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm (manufacturer figure)[1] | 300 x 300 x 300 mm or 350 x 350 x 350 mm. Sortable value is the 350 mm kit[2][3][5] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 389 x 389 x 457 mm - identical to the X1-Carbon[1] | Not documented |
| Net weight (kg) | 16 kg net (against 14.13 kg for the X1-Carbon)[1][6] | Not documented |
| Frame construction & material | Steel chassis with an aluminium and glass shell[1] | Blind-joint aluminium-extrusion frame with a complete panel set; stainless-steel linear rails throughout[3][5] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor, and the only X1 with active chamber heating; the chamber is controlled to a maximum of 60 C[1] | Enclosed by the supplied panel set. A Nevermore Micro V5 internal circulation filter is included in the LDO kit[5] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Actively heated chamber, maximum controlled temperature 60 C (manufacturer figure; not a passive measurement)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY, two stepper motors with one belt each (X1 series motion system)[9] | CoreXY on linear rails, with a belted flying gantry on four Z motors[3][2] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Carbon X rail as on the X1-Carbon (X1 series toolhead and gantry)[10] | Not documented |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Three leadscrews belt-driven from a single stepper motor, whole bed moving in Z (X1 series)[9] | Not documented |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | LDO Leviathan board: 5 x TMC2209 plus 2 x TMC5160 HV-capable drivers, ready for 48 V upgrades[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20 m/s2 = 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 32 mm3/s claimed on a 150x150 mm single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with hardened-steel extruder gears[1] | Clockwork 2 with a Bondtech BMG / Integrated Drive Gear Assembly, in a Stealthburner toolhead[2][3][5] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | All-metal hotend with a hardened-steel nozzle; 0.4 mm included, 0.2/0.6/0.8 mm optional; built-in filament cutter[1] | E3D Revo Voron (24 V), all-metal, high-flow variant in the Rev D+ kit, with a 60 W heater; upgradeable to a Phaetus Rapido HF for $9.99[2][3][5] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 320 C claimed max hot-end temperature - 20 C above the X1-Carbon[1][6] | Not documented |
| Heater cartridge power (W) | Not documented | 60 W (E3D Revo High Flow heater)[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C at 220 V, 120 C at 110 V max build-plate temperature[1] | Not documented |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate, Smooth PEI plate included; High Temperature, Textured PEI and Cool plates optional[1] | Cast 5083 aluminium plate with a magnetic base and a powder-coated PEI sheet; LDO silicone bed heater with edge-to-edge heating[3][2][5] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Nozzle-touch probing on the three ceramic heatbed force sensors, plus the Bambu micro-lidar for first-layer inspection[1][11] | Omron inductive probe supplied; Klicky-mod parts included. Voron Tap is available as an add-on rather than standard[2][3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor and door sensor; odometry with AMS[1] | Not documented |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hot-end fan, control-board fan, chamber temperature regulator fan and auxiliary part-cooling fan, all closed-loop controlled[1] | Not documented |
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | G3 pre-filter, H12 HEPA filter and granulated coconut-shell activated-carbon filter; VOC filtration rated Optimal and particulate filtration present[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller dual-core Cortex-M4; application processor quad ARM A7 at 1.2 GHz with a 2 TOPS NPU; 4 GB eMMC[1] | LDO x Voron Leviathan mainboard (replacing the earlier BTT Octopus), plus a Nitehawk SB USB toolhead PCB[3][2][5] |
| Total rated power draw | 100-240 VAC 50/60 Hz; 1400 W at 220 V, 750 W at 110 V[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[12] | Klipper, hosted on a Raspberry Pi 4B (included in the Fabreeko Rev D+ kit, not in the older 3DJake RevD kit)[2][3][5] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 1280x720 touchscreen[1] | 4.3-inch touchscreen included in the LDO kit[5] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus app and PC application[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi (802.11 b/g/n) plus 100 Mbps full-duplex RJ45 Ethernet, a network kill switch covering both Wi-Fi and Ethernet, a removable network module and 802.1X network access control - the feature set that distinguishes the X1E from every other Bambu machine. 4 GB eMMC and a microSD card reader[1] | Not documented |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in 1920x1080 chamber monitoring camera; micro-lidar also fitted[1] | Not documented |
| LED chamber/toolhead lighting | Not documented | COB LED strips included[2][5] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Not documented | Self-assembly kit; some parts must be printed by the user, and the LDO kit supplies pre-cut, pre-crimped cables and a heat-set insert soldering tip[5] |
| Materials Support | ||
| Officially supported filament list | Optimal: PLA, PETG, TPU, PVA, BVOH. Superior: ABS, ASA, PC, PA, PET and carbon/glass-fibre reinforced PLA, PETG, PA, PET, PC, ABS, ASA. Ideal: PPA-CF/GF, PPS, PPS-CF/GF[1] | Not documented |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Firmware over-temperature protection is documented for the X1 series: HMS_0300-0200-0001-0003 fires when the heater runs at full power without reaching target in time. Thresholds are not published and the firmware is closed-source[13] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[14] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab X1E Technical Specification (PDF) cdn1.bambulab.com · 2026-08 · doc
- Voron 2.4 R2 (Rev D+) kit by LDO fabreeko.com · 2026-08 · vendor
- LDO Voron 2.4 R2 (Rev D) kit listing matterhackers.com · 2026-08 · vendor
- Fabreeko Voron collection product feed (live prices) fabreeko.com · 2026-08 · vendor
- LDO Motors Voron 2.4 350 RevD kit contents 3djake.com · 2026-08 · vendor
- Bambu Lab X1-Carbon - Technical Specifications (PDF) public-cdn.bambulab.com · 2026-08 · doc
- Voron Trident R2 kit by LDO fabreeko.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab Wiki - X1 introduction wiki.bambulab.com · 2026-08 · doc
- PRNewswire - Bambu Lab Launches X1 Series, 23 May 2022 (Kickstarter dates and MSRP table) prnewswire.com · 2026-08 · doc
- Bambu Lab Wiki - Replace the Heatbed Sensor Unit / Heatbed Piezo Interface Board wiki.bambulab.com · 2026-08 · doc
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Wiki - HMS_0300-0200-0001-0003: nozzle heater over-temperature (X1 series) wiki.bambulab.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor