3D Printing InfoPrinter comparison
Bambu Lab X1E vs Original Prusa XL+ Single-Tool
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab X1E comparisonsMore Original Prusa XL+ Single-Tool comparisons
| Property | Bambu Lab X1ECOREXY | Original Prusa XL+ Single-ToolCOREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Prusa Research |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab X1E; spec PDF header "Bambu Lab X1E Technical Specification"[1] | Original Prusa XL+, Single-Tool variant ("Prusa XL+ Single-Tool" in the e-shop variant data)[2][3] |
| Release date (announcement and actual shipping) | Not documented | The XL+ refresh was announced on 13 August 2026, on sale immediately in all toolhead configurations, with assembled printers shipping later in August 2026 and upgrade kits for existing XL owners from around the end of August. The original Original Prusa XL predates it[4] |
| Street price (USD; dated snapshot per entry) | Not documented | $2,128.70 on prusa3d.com, Aug 2026 (lowest listed price for the Single-Tool variant; the Enclosure bundle starts at $2,610.19)[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Enterprise variant of the X1-Carbon, not a trim level. Differences from the X1C, from the two manufacturer spec sheets side by side: active chamber heating to 60 C (X1C has none), 320 C vs 300 C hot end, Smooth PEI plate included vs Cool/Engineering plates, G3+H12+carbon filter stack vs carbon filter only, Ethernet with a network kill switch, removable network module and 802.1X vs Wi-Fi only, 16 kg vs 14.13 kg, and 1400 W at 220 V / 750 W at 110 V vs 1000 W / 350 W[1][5] | The XL+ is sold in Single-Tool, Dual-Head and Five-Head variants at $2,128.70, $2,768.52 and $3,610.18 respectively (Aug 2026), plus Enclosure bundles and a Critical Infrastructure edition. The frame is the same in all of them - Prusa states the frame is ready for toolheads to be added at any time - so build volume, bed and electronics figures are shared and only the toolhead count and price differ. The XL+ is itself a revision of the Original Prusa XL: the older XL aligned toolheads with a mechanical pin, the XL+ uses a dedicated electronic sensor, adds a nozzle wiper and is claimed to print 10-15% faster[2][3] |
| Market position: superseded? successor announced? | Not present in the Bambu Lab US store 3D-printer collection in Aug 2026, which lists A1, A1 mini, A2L, P1S, P2S, X2D, H2S, H2D and H2C. Bambu sells business machines through a separate Business & Institution channel, so absence from the consumer collection is not proof of discontinuation; no live first-party price could be recorded[6] | Current model; an Original Prusa XL to Prusa XL+ upgrade kit is sold for existing owners[3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm (manufacturer figure)[1] | 360 x 360 x 360 mm, which Prusa states as 46.7 litres[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 389 x 389 x 457 mm - identical to the X1-Carbon[1] | About 700 x 900 x 720 mm (Prusa's own figure is approximate)[2] |
| Net weight (kg) | 16 kg net (against 14.13 kg for the X1-Carbon)[1][5] | About 30 kg[2] |
| Frame construction & material | Steel chassis with an aluminium and glass shell[1] | Aluminium extrusions and steel sheets (Prusa's comparison table for the XL)[7] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor, and the only X1 with active chamber heating; the chamber is controlled to a maximum of 60 C[1] | Open frame. The Enclosure for Prusa XL+ is an optional add-on; Prusa says the printer is ready for chamber temperatures up to 60 C, that the new better-sealed enclosure reaches around 50 C on the printer's own waste heat, and that 60 C needs an upcoming chamber heater for which no shipping date has been given[2][4] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Actively heated chamber, maximum controlled temperature 60 C (manufacturer figure; not a passive measurement)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY, two stepper motors with one belt each (X1 series motion system)[8] | CoreXY with 1.5 mm GT belts, Input Shaper and Phase Stepping[2] |
| X-axis guide type (rods / linear rails / V-wheels; size) | Carbon X rail as on the X1-Carbon (X1 series toolhead and gantry)[9] | Not documented |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Three leadscrews belt-driven from a single stepper motor, whole bed moving in Z (X1 series)[8] | Not documented |
| Belts (type, width, e.g. Gates?) | Not documented | 1.5 mm GT belts[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 20 m/s2 = 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 32 mm3/s claimed on a 150x150 mm single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | Not documented | Input Shaper and Phase Stepping[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with hardened-steel extruder gears[1] | Nextruder direct drive; each toolhead carries its own extruder, hotend, nozzle and filament[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | All-metal hotend with a hardened-steel nozzle; 0.4 mm included, 0.2/0.6/0.8 mm optional; built-in filament cutter[1] | Quick-swap nozzles - 0.25 mm for detail, 0.6/0.8 mm for speed, hardened steel for abrasives, high-flow CHT for throughput; toolheads ship with high-flow nozzles[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 320 C claimed max hot-end temperature - 20 C above the X1-Carbon[1][5] | 290 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C at 220 V, 120 C at 110 V max build-plate temperature[1] | 120 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate, Smooth PEI plate included; High Temperature, Textured PEI and Cool plates optional[1] | Segmented heatbed of 16 individually controlled tiles across the 360 x 360 mm surface, so only the tiles under the part are powered; removable double-sided satin print sheet supplied[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Nozzle-touch probing on the three ceramic heatbed force sensors, plus the Bambu micro-lidar for first-layer inspection[1][10] | Load-cell sensor - the nozzle is the probe, which Prusa says automatically accounts for nozzle changes, surface textures and thermal expansion and removes manual Z-offsets. Toolhead-to-toolhead alignment on the XL+ uses a separate permanently mounted eddy-current Tool Offset Sensor, replacing the removable mechanical pin used on the original XL[2][4] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor and door sensor; odometry with AMS[1] | Filament sensors fitted; Prusa's comparison table lists two filament sensors for the XL[7] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hot-end fan, control-board fan, chamber temperature regulator fan and auxiliary part-cooling fan, all closed-loop controlled[1] | 360-degree part cooling on each toolhead, new on the XL+ and matching the MK4S and CORE One arrangement; Prusa states it delivers more airflow and distributes it more evenly around the nozzle. Additional fans and heatsinks cool the electronics. Fan sizes are not published[2][4] |
| Chamber/exhaust fan & filtration (activated carbon / HEPA) | G3 pre-filter, H12 HEPA filter and granulated coconut-shell activated-carbon filter; VOC filtration rated Optimal and particulate filtration present[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller dual-core Cortex-M4; application processor quad ARM A7 at 1.2 GHz with a 2 TOPS NPU; 4 GB eMMC[1] | Custom 32-bit xBuddy electronics with STM32 (Prusa's comparison table for the XL)[7] |
| Total rated power draw | 100-240 VAC 50/60 Hz; 1400 W at 220 V, 750 W at 110 V[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[11] | Open-source firmware - Prusa states "Firmware: Open-source; ships with the full current Prusa feature set", and the XL is covered by the prusa3d/Prusa-Firmware-Buddy source tree[2][12] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 1280x720 touchscreen[1] | 3.5-inch 65k-colour screen with touch control (Prusa's comparison table for the XL)[7] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus app and PC application[1] | On-device touch UI; Prusa Connect and the Prusa mobile app are optional - Prusa states the machine is fully offline capable[7][2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi (802.11 b/g/n) plus 100 Mbps full-duplex RJ45 Ethernet, a network kill switch covering both Wi-Fi and Ethernet, a removable network module and 802.1X network access control - the feature set that distinguishes the X1E from every other Bambu machine. 4 GB eMMC and a microSD card reader[1] | Ethernet, optional Wi-Fi; USB drive for print files. Prusa Connect optional and fully offline operation supported[2][7] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in 1920x1080 chamber monitoring camera; micro-lidar also fitted[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Optimal: PLA, PETG, TPU, PVA, BVOH. Superior: ABS, ASA, PC, PA, PET and carbon/glass-fibre reinforced PLA, PETG, PA, PET, PC, ABS, ASA. Ideal: PPA-CF/GF, PPS, PPS-CF/GF[1] | PLA, PETG, ASA, ABS, PC, PA (nylon), TPU, PVA, HIPS, PP, CPE, PVB and carbon-fibre composites. Prusa states an open material policy - any brand of 1.75 mm filament, no chips and no subscriptions[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Firmware over-temperature protection is documented for the X1 series: HMS_0300-0200-0001-0003 fires when the heater runs at full power without reaching target in time. Thresholds are not published and the firmware is closed-source[13] | Open-source firmware on the xBuddy platform, which carries hardware overcurrent protection cutting heater and heatbed power above 15 A[14][12] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[15] | 2-year warranty for consumers in the EU, Liechtenstein, Switzerland, Norway and Iceland; 1 year for EU enterprises and 1 year for the rest of the world, which includes the United States. A printer bought from a reseller or privately carries 1 year from the original delivery date and is handled by the reseller. Prusa advertises 24/7 chat and e-mail support in seven languages[16][7] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab X1E Technical Specification (PDF) cdn1.bambulab.com · 2026-08 · doc
- Original Prusa XL+ product page (spec block and variant price data) prusa3d.com · 2026-08 · vendor
- Prusa 3D printers category listing with live e-shop prices, Aug 2026 prusa3d.com · 2026-08 · vendor
- Prusa blog - Better Prints, Easier Use: Prusa XL+, CORE One L+ and CORE One+ (Gen 2), Our Big Product Update (published 13 August 2026) blog.prusa3d.com · 2026-08 · doc
- Bambu Lab X1-Carbon - Technical Specifications (PDF) public-cdn.bambulab.com · 2026-08 · doc
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Original Prusa MK4S 3D Printer product page (Technical Parameters + CORE One+/MK4S/XL comparison table) prusa3d.com · 2026-08 · vendor
- Bambu Lab Wiki - X1 introduction wiki.bambulab.com · 2026-08 · doc
- PRNewswire - Bambu Lab Launches X1 Series, 23 May 2022 (Kickstarter dates and MSRP table) prnewswire.com · 2026-08 · doc
- Bambu Lab Wiki - Replace the Heatbed Sensor Unit / Heatbed Piezo Interface Board wiki.bambulab.com · 2026-08 · doc
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- GitHub - prusa3d/Prusa-Firmware-Buddy (firmware for MINI, MK4, XL and CORE One) github.com · 2026-08 · doc
- Bambu Lab Wiki - HMS_0300-0200-0001-0003: nozzle heater over-temperature (X1 series) wiki.bambulab.com · 2026-08 · doc
- Prusa blog - Original Prusa MK4 is here (published 29 March 2023), including the MK4 specification table and launch prices blog.prusa3d.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- Prusa Knowledge Base - Warranty help.prusa3d.com · 2026-08 · doc