3D Printing InfoPrinter comparison
Bambu Lab P2S vs Snapmaker U1
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab P2S comparisonsMore Snapmaker U1 comparisons
| Property | Bambu Lab P2SCOREXY | Snapmaker U1TOOLCHANGER |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Snapmaker |
| Class | COREXY | TOOLCHANGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[1] | Snapmaker U1 3D Printer[2] |
| Street price (USD; dated snapshot per entry) | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[3][4] | $849.00 against a $999.00 compare-at price on us.snapmaker.com, but the listing is marked Unavailable, checked Aug 2026[2] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[1][5] | An optional top cover changes what the machine can print: without it PLA/PETG/TPU/PVA/PCTG; with it ABS, ASA, PA, PC and PET are added; with the top cover AND a hardened-steel nozzle, carbon- and glass-fibre grades. A stated material list for the U1 is therefore meaningless without saying which configuration it refers to[2] |
| Market position: superseded? successor announced? | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[3] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm (manufacturer figure)[1] | 270 x 270 x 270 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | 584 x 499 x 730 mm[2] |
| Net weight (kg) | 14.9 kg net[1] | 18.2 kg[2] |
| Frame construction & material | Plastic and steel chassis with a plastic and glass outer frame[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[1] | Open as sold; a top cover is an optional accessory that raises the supported material range[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[1][4] | Four independent toolheads on a changer; Snapmaker quotes a 5-second swap[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | 500 mm/s maximum toolhead speed (manufacturer claim)[2] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 20,000 mm/s2 maximum (manufacturer claim)[2] |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | 32 mm3/s maximum hotend flow (manufacturer claim)[2] |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | Not documented | Input shaping with an accelerometer, run as a calibration routine[2] |
| Extrusion Pressure Control | ||
| Pressure advance (Klipper) / linear advance (Marlin) supported? | Not documented | Pressure advance, with automatic flow compensation calibration[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 °C maximum (manufacturer claim)[2] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Stainless steel as standard; hardened steel needed for fibre-filled grades[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heatbed temperature[1] | 100 °C maximum (manufacturer claim)[2] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[1] | Flexible steel sheet with a PEI surface[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | Mesh bed levelling. Automatic toolhead offset calibration is done by coordinate measuring[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[1] | Filament run-out detection, plus air-printing detection and RFID filament recognition[2] |
| Multi-material/multi-color capability or official upgrade path | Not documented | Four toolheads with auto-feed and a backup mode; toolhead swap error detection, build-plate presence and obstruction detection[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[1] | Main plus auxiliary part-cooling fans[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[1] | Not documented |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[1] | Maximum input power 1150 W at 220-240 V, 400 W at 100-120 V; maximum input current 6 A / 4 A respectively[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[6] | Klipper[2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 854x480 touchscreen[1] | 3.5-inch, 320 x 480 touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[1] | Wi-Fi 2.4 GHz (802.11b/g/n) and USB flash drive. No Ethernet listed[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[1][5] | 2 MP built-in chamber camera for live view[2] |
| Power-Loss & Interruption Recovery | ||
| Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?) | Not documented | Power-loss recovery supported; mechanism not published[2] |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[1] | Base: PLA, PETG, TPU, PVA, PCTG. With the optional top cover: adds PET, ABS, ASA, PA, PC. With top cover and a hardened-steel nozzle: adds carbon- and glass-fibre-reinforced polymers[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[7] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Snapmaker U1 product page us.snapmaker.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor