3D Printing InfoPrinter comparison
Bambu Lab P2S vs QIDI X-Smart 3
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab P2S comparisonsMore QIDI X-Smart 3 comparisons
| Property | Bambu Lab P2SCOREXY | QIDI X-Smart 3COREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | QIDI |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[1] | QIDI X-Smart 3, listed in QIDI navigation as X-Smart3[2][3] |
| Release date (announcement and actual shipping) | Not documented | Not published by QIDI on the pages checked (Aug 2026)[2][3] |
| Street price (USD; dated snapshot per entry) | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[4][5] | $399 on QIDI's official US page, which routes purchases to its AliExpress and Amazon stores; checked Aug 2026[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[1][6] | Entry model of the 3-series. Unlike the X-Plus 3 and X-Max 3 it has no heated chamber, a 300 °C rather than 350 °C hotend, a brass rather than copper-alloy/hardened-steel nozzle head, and no Ethernet. It shares the Cortex-A53 board with them, so control-board specs must not be read as shared print specs[2][7][8] |
| Market position: superseded? successor announced? | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[4] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm (manufacturer figure)[1] | 175 x 180 x 170 mm advertised[2][3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | 370 x 362 x 397 mm[2] |
| Net weight (kg) | 14.9 kg net[1] | 10.5 kg[2] |
| Frame construction & material | Plastic and steel chassis with a plastic and glass outer frame[1] | QIDI publishes no frame-material breakdown for this model[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[1] | No heated chamber. 3DJake's table records "Heated chamber: No"; QIDI does not describe an enclosure for this model[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[1][5] | CoreXY[2][3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | <=500 mm/s (manufacturer claim)[2][3] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 20,000 mm/s2 (manufacturer claim)[3] |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | 30 mm3/s extruder flow (manufacturer claim)[2][3] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[1] | Direct-drive extruder, single, 1.75 mm filament[2][3] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[1] | Brass nozzle head. 0.4 mm stock, 0.2/0.6/0.8 mm optional[2][3] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | <=300 °C claimed[2][3] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Brass[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heatbed temperature[1] | <=120 °C claimed[2][3] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[1] | Double-sided flexible magnetic RF plate[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | 16-point automatic bed levelling per QIDI's US page; probe technology not named[3] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 16 points (QIDI's US page). Not verified against firmware[3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[1] | Filament detection fitted; type and location not published[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[1] | Not documented |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | Cortex-A53 64-bit at 1.5 GHz, 1 GB DDR3, 8 GB eMMC[2] |
| Input voltage (110/220 V, switch or auto) | Not documented | 100-240 VAC, 50/60 Hz[2] |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[1] | 350 W rated[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[9] | Klipper[3] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 854x480 touchscreen[1] | 4.3-inch touchscreen[3] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[1] | Wi-Fi and USB. No Ethernet listed for this model[2][3] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[1][6] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[10] | 1-year coverage (QIDI standard store terms)[11] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- QIDI Tech X-Smart 3 technical data table 3djake.com · 2026-08 · vendor
- QIDI X-Smart 3 official US page qidiusa.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- QIDI Tech X-Plus 3 technical data table 3djake.com · 2026-08 · vendor
- QIDI Tech X-Max 3 technical data table 3djake.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- QIDI Max4 product page (US store) us.qidi3d.com · 2026-08 · vendor