3D Printing InfoPrinter comparison
Bambu Lab P2S vs ELEGOO Neptune 4 Max
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab P2S comparisonsMore ELEGOO Neptune 4 Max comparisons
| Property | Bambu Lab P2SCOREXY | ELEGOO Neptune 4 MaxBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | ELEGOO |
| Class | COREXY | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[1] | ELEGOO Neptune 4 Max[2] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date)[3] |
| Street price (USD; dated snapshot per entry) | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[4][5] | $389.00 on us.elegoo.com, Aug 2026, against a compare-at price of $559.99; Ribbon-Cable and Type-C printhead variants are the same price[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[1][6] | Largest Neptune 4. The trade-off against the smaller models is easy to miss: the bed only reaches 85 C (against 100 C on the Plus and 110 C on the base Neptune 4) and acceleration is capped at 8000 mm/s2 (against 12000 and 20000), because of the mass of a 430 x 430 mm moving bed. Two printhead variants, Ribbon-Cable and Type-C, are sold under one SKU[2][7][8][3] |
| Market position: superseded? successor announced? | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[4] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm (manufacturer figure)[1] | 420 x 420 x 480 mm; printing platform 430 x 430 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | 658 x 632 x 740 mm; ELEGOO's maximum size for machine activity is 658 x 950 x 960 mm including rack and tray - allow nearly a metre of depth and height[2] |
| Net weight (kg) | 14.9 kg net[1] | 18.1 kg net, 21.8 kg gross[2] |
| Frame construction & material | Plastic and steel chassis with a plastic and glass outer frame[1] | CNC-machined aluminium extrusion frame[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[1] | Open frame, no enclosure[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[1][5] | Cartesian i3 bed-slinger[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Two lead screws with two tie rods[9] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)"; no driver part number published[9] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | 500 mm/s max toolhead speed (manufacturer claim)[2] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure); default acceleration is 4000 mm/s2[9] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 8000 mm/s2 max toolhead acceleration (manufacturer claim) - the lowest in the Neptune 4 family[2] |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[1] | Dual-gear direct extruder with 2 fans[9] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[1] | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[9] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heatbed temperature[1] | 85 C max heated bed temperature at 25 C ambient - well below the 100-110 C of the smaller Neptunes, which limits ABS/ASA work despite them being on the compatibility list[2] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[1] | PEI spring steel sheet, now upgraded to a dual-sided textured PEI + PLA-specific surface; platform 430 x 430 mm[9] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | Manual levelling combined with 121-point auto-levelling[9] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[1] | Filament detection and power-loss resume printing[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[1] | "Klipper High-Speed Quiet Motherboard" is all ELEGOO publishes[9] |
| Input voltage (110/220 V, switch or auto) | Not documented | 100-120 V / 220-240 V, 50/60 Hz[2][9] |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[1] | 320 W rated power, 24 V output[9] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[10] | Klipper[9] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 854x480 touchscreen[1] | 4.3-inch colour capacitive touch screen[9] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[1] | Colour capacitive touch UI; ElegooSlicer recommended, Orca and Cura supported[9] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[1] | Wi-Fi, USB and WLAN file transfer[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[1][6] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[1] | PLA, TPU, PETG, ABS, ASA, Nylon - but note the 85 C bed ceiling against ABS and ASA[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound published as 65 dB or less - a manufacturer figure with no distance or method stated[9] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[11] | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[12] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor