3D Printing InfoPrinter comparison
Bambu Lab P2S vs Creality K2
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab P2S comparisonsMore Creality K2 comparisons
| Property | Bambu Lab P2SCOREXY | Creality K2COREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | Creality |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[1] | Creality K2[2] |
| Street price (USD; dated snapshot per entry) | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[3][4] | Not documented |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[1][5] | Smallest of three K2 machines that share a product page. K2: 260 mm cube, no chamber heating, 100 C bed, 300 C nozzle, 8 GB storage, one air filter, one auxiliary cooling fan, 720p camera, no RFID reader, no Ethernet. K2 Pro: 300 mm cube, 60 C chamber, 110 C bed, RFID, Ethernet, 32 GB. K2 Plus: 350 mm cube, 350 C nozzle, 120 C bed, 30000 mm/s2, dual air filters, auto belt tensioning, 1080p camera, dual-band Wi-Fi. A K2 SE also exists as a separate model[2] |
| Market position: superseded? successor announced? | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[3] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 256 x 256 x 256 mm (manufacturer figure)[1] | 260 x 260 x 260 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 392 x 406 x 478 mm[1] | 404 x 436 x 545 mm[2] |
| Net weight (kg) | 14.9 kg net[1] | 18.3 kg[2] |
| Frame construction & material | Plastic and steel chassis with a plastic and glass outer frame[1] | Not documented |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[1] | Enclosed, but with no chamber temperature control - Creality's table gives a max chamber temperature for the K2 Pro and K2 Plus and a dash for the K2. One air filter fitted[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[1][4] | CoreXY - Creality groups the K2 series with its CoreXY flagships and quotes 600 mm/s with step-servo motors on the X and Y axes[2] |
| Belts (type, width, e.g. Gates?) | Not documented | Manual belt tensioning (the K2 Plus is auto-adjusted)[2] |
| Stepper motors (frame size, step angle, brand if known) | Not documented | Step-servo motors on the X and Y axes and the extruder (the K2 Plus adds them on Z)[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | 600 mm/s max printing speed (manufacturer claim)[2] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 20000 mm/s2 max acceleration (manufacturer claim)[2] |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C claimed max nozzle temperature[1] | 300 C claimed max nozzle temperature[2] |
| Heater cartridge power (W) | Not documented | 70 W rated hotend power[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C max heatbed temperature[1] | 100 C max heatbed temperature - the lowest in the K2 family[2] |
| Bed surface (material, texture, coating), single/double-sided | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | Smart auto levelling fitted; unlike the K2 Pro and Plus there is no nozzle AI camera, so there is no automatic flow-rate calibration[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[1] | Not documented |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[1] | One auxiliary cooling fan and one air filter[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[1] | Not documented |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[1] | Not documented |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[6] | Creality OS, a Klipper derivative. Creality publishes the K2 firmware source as CrealityOfficial/K2_Series_Klipper on GitHub under GPL-3.0, last pushed March 2026[7][8][2] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 854x480 touchscreen[1] | 4-inch touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[1] | Touch UI with alarm sounds; no built-in RFID reader[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[1] | Wi-Fi 2.4 GHz, USB drive and a Creality 485 port; no Ethernet. 8 GB eMMC storage[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[1][5] | One chamber camera, 720p at 30 fps[2] |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[1] | PLA, PETG, PET, ABS, PLA-CF - a shorter list than the K2 Pro and Plus, which add ASA, PA-CF and PPA-CF[2] |
| Safety | ||
| Thermal runaway protection (verify in firmware source if at all possible) | Not documented | Not verified directly. Creality publishes the K2-series firmware as CrealityOfficial/K2_Series_Klipper (GPL-3.0); upstream Klipper ships the verify_heater thermal-runaway check, but whether the stock configuration enables it was not checked here[7][8] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[9] | Creality's US store states "Up to 12-Month Warranty", a 14-day return and refund window and "Lifetime Customer Support" on its printer product pages. The "up to" wording means the term is not uniform across parts[10] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Creality K2 series product page, including the Compare K2 Series table (K2 / K2 Pro / K2 Plus) creality.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- GitHub API - CrealityOfficial/K2_Series_Klipper repository metadata (GPL-3.0, last push Mar 2026) api.github.com · 2026-08 · doc
- GitHub - CrealityOfficial organisation repositories (per-model firmware sources) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- Creality US store - K1 3D Printer product page (live price, warranty and returns banner) store.creality.com · 2026-08 · vendor