3D Printing InfoPrinter comparison
Bambu Lab H2D vs QIDI X-Smart 3
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab H2D comparisonsMore QIDI X-Smart 3 comparisons
| Property | Bambu Lab H2DCOREXY | QIDI X-Smart 3COREXY |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | QIDI |
| Class | COREXY | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab H2D[1] | QIDI X-Smart 3, listed in QIDI navigation as X-Smart3[2][3] |
| Release date (announcement and actual shipping) | Not documented | Not published by QIDI on the pages checked (Aug 2026)[2][3] |
| Street price (USD; dated snapshot per entry) | From $1,549.00 on the Bambu Lab US store, Aug 2026, against a stated typical price of $1,749.00; the product page shows $1,749.00 (typical $1,999.00) with a combo variant selected[4][5] | $399 on QIDI's official US page, which routes purchases to its AliExpress and Amazon stores; checked Aug 2026[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Six SKUs on one product page including H2D, H2D AMS Combo and H2D Laser Full Combo. The Laser Edition adds laser safety windows and the air-assist pump; a plain H2D can be upgraded with a Laser Upgrade Kit. The BirdsEye camera is only fitted on the Laser Edition. Siblings in the same family are the H2S (single nozzle, 340x320x340 mm, 30 kg) and H2C (dual nozzle, 305x320x325 mm single-nozzle volume, 32.5 kg, four cameras as standard) - all three share the 492x514x626 mm body, so body dimensions alone will not tell them apart[1][6][7] | Entry model of the 3-series. Unlike the X-Plus 3 and X-Max 3 it has no heated chamber, a 300 °C rather than 350 °C hotend, a brass rather than copper-alloy/hardened-steel nozzle head, and no Ethernet. It shares the Cortex-A53 board with them, so control-board specs must not be read as shared print specs[2][8][9] |
| Market position: superseded? successor announced? | Current model; the H2C sits above it in the same body at $2,199 and the H2S below it at $1,199[4] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | Single-nozzle printing 325 x 320 x 325 mm; dual-nozzle printing 300 x 320 x 320 mm; total volume across the two nozzles 350 x 320 x 320 mm. The sortable figure is the single-nozzle volume[1] | 175 x 180 x 170 mm advertised[2][3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 492 x 514 x 626 mm[1] | 370 x 362 x 397 mm[2] |
| Net weight (kg) | 31 kg net[1] | 10.5 kg[2] |
| Frame construction & material | Aluminium, steel, plastic and glass chassis and shell[1] | QIDI publishes no frame-material breakdown for this model[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor; active chamber heating to 65 C, chamber exhaust and heat-circulation fans, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack[1] | No heated chamber. 3DJake's table records "Heated chamber: No"; QIDI does not describe an enclosure for this model[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Active chamber heating, maximum 65 C (manufacturer figure)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - not named in the spec sheet; Bambu groups the H2 series with its enclosed CoreXY machines at 20000 mm/s2[1] | CoreXY[2][3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | <=500 mm/s (manufacturer claim)[2][3] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 20,000 mm/s2 (manufacturer claim)[3] |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s with the standard-flow hotend, 65 mm3/s with the optional high-flow hotend; both measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | 30 mm3/s extruder flow (manufacturer claim)[2][3] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual direct-drive extruders with hardened-steel gears, driven by Bambu high-precision permanent-magnet synchronous motors[1] | Direct-drive extruder, single, 1.75 mm filament[2][3] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | All-metal hotend with hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; an optional high-flow hotend is offered[1] | Brass nozzle head. 0.4 mm stock, 0.2/0.6/0.8 mm optional[2][3] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 350 C claimed max nozzle temperature[1] | <=300 °C claimed[2][3] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Brass[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 120 C max heatbed temperature[1] | <=120 °C claimed[2][3] |
| Bed surface (material, texture, coating), single/double-sided | Textured PEI plate and Smooth PEI plate supported[1] | Double-sided flexible magnetic RF plate[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | 16-point automatic bed levelling per QIDI's US page; probe technology not named[3] |
| Mesh grid size (probe point count — firmware evidence) | Not documented | 16 points (QIDI's US page). Not verified against firmware[3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1] | Filament detection fitted; type and location not published[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, auxiliary part-cooling fan, chamber heat-circulation fan, hotend cooling fan, main control board fan and chamber exhaust fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Not documented | Cortex-A53 64-bit at 1.5 GHz, 1 GB DDR3, 8 GB eMMC[2] |
| Input voltage (110/220 V, switch or auto) | Not documented | 100-240 VAC, 50/60 Hz[2] |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; 2200 W at 220 V, 1320 W at 110 V. The US store page states the H2D it sells is the 100-120 V version[1] | 350 W rated[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[10] | Klipper[3] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 720x1280 touchscreen[1] | 4.3-inch touchscreen[3] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus Bambu Studio, Bambu Suite and Bambu Handy[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port[1] | Wi-Fi and USB. No Ethernet listed for this model[2][3] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Four cameras listed: live view 1920x1080, nozzle camera 1920x1080, toolhead camera 1920x1080, and a 3264x2448 BirdsEye camera fitted only on the Laser Edition[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, TPU, PVA, BVOH, ABS, ASA, PC, PA, PET, plus carbon/glass-fibre reinforced PLA, PETG, PA, PET, PC, ABS, ASA, PPA-CF/GF, PPS and PPS-CF/GF[1] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[11] | 1-year coverage (QIDI standard store terms)[12] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab H2D - Technical Specifications bambulab.com · 2026-08 · vendor
- QIDI Tech X-Smart 3 technical data table 3djake.com · 2026-08 · vendor
- QIDI X-Smart 3 official US page qidiusa.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab H2D store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab H2S & H2S Laser Edition Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab H2C Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- QIDI Tech X-Plus 3 technical data table 3djake.com · 2026-08 · vendor
- QIDI Tech X-Max 3 technical data table 3djake.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- QIDI Max4 product page (US store) us.qidi3d.com · 2026-08 · vendor