3D Printing InfoPrinter comparison
Bambu Lab H2D vs ELEGOO Neptune 4 Max
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Bambu Lab H2D comparisonsMore ELEGOO Neptune 4 Max comparisons
| Property | Bambu Lab H2DCOREXY | ELEGOO Neptune 4 MaxBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | Bambu Lab | ELEGOO |
| Class | COREXY | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Bambu Lab H2D[1] | ELEGOO Neptune 4 Max[2] |
| Release date (announcement and actual shipping) | Not documented | Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date)[3] |
| Street price (USD; dated snapshot per entry) | From $1,549.00 on the Bambu Lab US store, Aug 2026, against a stated typical price of $1,749.00; the product page shows $1,749.00 (typical $1,999.00) with a combo variant selected[4][5] | $389.00 on us.elegoo.com, Aug 2026, against a compare-at price of $559.99; Ribbon-Cable and Type-C printhead variants are the same price[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Six SKUs on one product page including H2D, H2D AMS Combo and H2D Laser Full Combo. The Laser Edition adds laser safety windows and the air-assist pump; a plain H2D can be upgraded with a Laser Upgrade Kit. The BirdsEye camera is only fitted on the Laser Edition. Siblings in the same family are the H2S (single nozzle, 340x320x340 mm, 30 kg) and H2C (dual nozzle, 305x320x325 mm single-nozzle volume, 32.5 kg, four cameras as standard) - all three share the 492x514x626 mm body, so body dimensions alone will not tell them apart[1][6][7] | Largest Neptune 4. The trade-off against the smaller models is easy to miss: the bed only reaches 85 C (against 100 C on the Plus and 110 C on the base Neptune 4) and acceleration is capped at 8000 mm/s2 (against 12000 and 20000), because of the mass of a 430 x 430 mm moving bed. Two printhead variants, Ribbon-Cable and Type-C, are sold under one SKU[2][8][9][3] |
| Market position: superseded? successor announced? | Current model; the H2C sits above it in the same body at $2,199 and the H2S below it at $1,199[4] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | Single-nozzle printing 325 x 320 x 325 mm; dual-nozzle printing 300 x 320 x 320 mm; total volume across the two nozzles 350 x 320 x 320 mm. The sortable figure is the single-nozzle volume[1] | 420 x 420 x 480 mm; printing platform 430 x 430 mm[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 492 x 514 x 626 mm[1] | 658 x 632 x 740 mm; ELEGOO's maximum size for machine activity is 658 x 950 x 960 mm including rack and tray - allow nearly a metre of depth and height[2] |
| Net weight (kg) | 31 kg net[1] | 18.1 kg net, 21.8 kg gross[2] |
| Frame construction & material | Aluminium, steel, plastic and glass chassis and shell[1] | CNC-machined aluminium extrusion frame[2] |
| Enclosure: open / enclosed; panel material; door/lid | Fully enclosed with a door sensor; active chamber heating to 65 C, chamber exhaust and heat-circulation fans, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack[1] | Open frame, no enclosure[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Active chamber heating, maximum 65 C (manufacturer figure)[1] | Not documented |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | CoreXY - not named in the spec sheet; Bambu groups the H2 series with its enclosed CoreXY machines at 20000 mm/s2[1] | Cartesian i3 bed-slinger[2] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Not documented | Two lead screws with two tie rods[10] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | "Silent Drive (All Axes)"; no driver part number published[10] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[1] | 500 mm/s max toolhead speed (manufacturer claim)[2] |
| Recommended/typical print speed | Not documented | 250 mm/s recommended printing speed against the 500 mm/s ceiling (ELEGOO's own figure); default acceleration is 4000 mm/s2[10] |
| Max acceleration (claimed, mm/s²) | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[1] | 8000 mm/s2 max toolhead acceleration (manufacturer claim) - the lowest in the Neptune 4 family[2] |
| Max volumetric flow claimed (mm³/s) | 40 mm3/s with the standard-flow hotend, 65 mm3/s with the optional high-flow hotend; both measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Dual direct-drive extruders with hardened-steel gears, driven by Bambu high-precision permanent-magnet synchronous motors[1] | Dual-gear direct extruder with 2 fans[10] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | All-metal hotend with hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; an optional high-flow hotend is offered[1] | Brass nozzle, 0.4 mm, with a titanium-alloy heat break[10] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 350 C claimed max nozzle temperature[1] | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 120 C max heatbed temperature[1] | 85 C max heated bed temperature at 25 C ambient - well below the 100-110 C of the smaller Neptunes, which limits ABS/ASA work despite them being on the compatibility list[2] |
| Bed surface (material, texture, coating), single/double-sided | Textured PEI plate and Smooth PEI plate supported[1] | PEI spring steel sheet, now upgraded to a dual-sided textured PEI + PLA-specific surface; platform 430 x 430 mm[10] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Not documented | Manual levelling combined with 121-point auto-levelling[10] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[1] | Filament detection and power-loss resume printing[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan, auxiliary part-cooling fan, chamber heat-circulation fan, hotend cooling fan, main control board fan and chamber exhaust fan, all closed-loop controlled[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | "Klipper High-Speed Quiet Motherboard" is all ELEGOO publishes[10] |
| Input voltage (110/220 V, switch or auto) | Not documented | 100-120 V / 220-240 V, 50/60 Hz[2][10] |
| Total rated power draw | 100-120 VAC / 200-240 VAC 50/60 Hz; 2200 W at 220 V, 1320 W at 110 V. The US store page states the H2D it sells is the 100-120 V version[1] | 320 W rated power, 24 V output[10] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[11] | Klipper[10] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 5-inch 720x1280 touchscreen[1] | 4.3-inch colour capacitive touch screen[10] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus Bambu Studio, Bambu Suite and Bambu Handy[1] | Colour capacitive touch UI; ElegooSlicer recommended, Orca and Cura supported[10] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port[1] | Wi-Fi, USB and WLAN file transfer[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Four cameras listed: live view 1920x1080, nozzle camera 1920x1080, toolhead camera 1920x1080, and a 3264x2448 BirdsEye camera fitted only on the Laser Edition[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, TPU, PVA, BVOH, ABS, ASA, PC, PA, PET, plus carbon/glass-fibre reinforced PLA, PETG, PA, PET, PC, ABS, ASA, PPA-CF/GF, PPS and PPS-CF/GF[1] | PLA, TPU, PETG, ABS, ASA, Nylon - but note the 85 C bed ceiling against ABS and ASA[2] |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | Not documented | Operating sound published as 65 dB or less - a manufacturer figure with no distance or method stated[10] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[12] | 12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[13] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Bambu Lab H2D - Technical Specifications bambulab.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab H2D store page us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab H2S & H2S Laser Edition Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab H2C Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
- ELEGOO compare-products page, which embeds the full per-model specification JSON for every Neptune, Centauri and OrangeStorm machine us.elegoo.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor
- ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor