3D Printing InfoPrinter comparison
Anycubic Kobra 3 Max vs FlashForge Creator 5
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Anycubic Kobra 3 Max comparisonsMore FlashForge Creator 5 comparisons
| Property | Anycubic Kobra 3 MaxBEDSLINGER | FlashForge Creator 5TOOLCHANGER |
|---|---|---|
| Identity | ||
| Brand | Anycubic | FlashForge |
| Class | BEDSLINGER | TOOLCHANGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Anycubic Kobra 3 Max[1] | Flashforge Creator 5, sold as "Creator 5 4-Toolheads Multi-Color 3D Printer"[2][3] |
| Release date (announcement and actual shipping) | Listed on the Anycubic store from 19 February 2025 (Shopify publish date)[4] | Announced with a $10 deposit programme; shipping to deposit backers by 19 May 2026. One secondary source puts general release in early May 2026[5][6] |
| Launch MSRP (USD) | Not documented | $649 early-bird (deposit price, open until 20 June 2026); $799 standard MSRP[5][6] |
| Street price (USD; dated snapshot per entry) | $429.00 with a US plug on store.anycubic.com, Aug 2026, against a compare-at price of $699.00 ($493.00 for the EU plug variant)[4] | $799.00 on flashforge.com, in stock, with $100 auto-applied in cart, checked Aug 2026[2][3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Same 420 x 420 x 500 mm build volume as the older Kobra 2 Max, so build volume will not tell them apart - but the Kobra 3 Max is faster (600 mm/s claimed against 500), runs Kobra OS with multi-colour support and a 4.3-inch touchscreen, and is lighter at 19 kg against 21 kg. Its acceleration ceiling is 10000 mm/s2, half the 20000 mm/s2 of the smaller Kobra 3 - a difference the marketing does not lead with[1][7][8] | Paired with the Creator 5 Pro at $949, which adds a sealed enclosure, 65 °C active chamber heating and HEPA13 + carbon filtration. Motion system, 256 mm build volume, four toolheads, 600 mm/s and 30,000 mm/s2 are the same on both, so enclosure and chamber are the only reliable discriminators[2][9][5][6][3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 420 x 420 x 500 mm, which Anycubic states as 88 L[1] | 256 x 256 x 256 mm[5][6][10] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 706 x 640 x 753 mm[1] | Not documented |
| Net weight (kg) | 19 kg[1] | Not documented |
| Frame construction & material | Not documented | CoreXY frame; FlashForge does not publish a frame-material breakdown and no dimensions or weight have been published for this model[5][6] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Open frame. No enclosure, no chamber heating and no filtration[5][6][10] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Anycubic's table gives the construction as "Gantry System" - a bed-slinger, with dual Y-axis motors added to stop layer misalignment on the large moving bed[1] | CoreXY with four independent toolheads on a FlashSwap changer. FlashForge claims a physical head swap in about 7 seconds[5][6][10] |
| Belts (type, width, e.g. Gates?) | Semi-automatic belt tensioning, which Anycubic pairs with motor anti-skip[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 600 mm/s maximum print speed (manufacturer claim), 300 mm/s recommended[1] | 600 mm/s maximum, reported by both secondary sources as a travel-speed figure (manufacturer claim)[5][6] |
| Recommended/typical print speed | 300 mm/s recommended print speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 10000 mm/s2 maximum acceleration - half the ceiling of the smaller Kobra 3, because of the moving mass[1][8] | 30,000 mm/s2 maximum (manufacturer claim)[5][6] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive ("short distance extrusion") with a quick-release hotend[1] | Not documented |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | 300 C quick-release hotend with an aerospace-grade ceramic composite throat tube; 0.4 mm standard nozzle, expandable to 0.6 and 0.8 mm[1] | Not documented |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 300 C maximum nozzle temperature[1] | Not documented |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel nozzles as standard[5][6] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 90 C maximum hotbed temperature on a PEI spring steel plate - 20 C below the smaller Kobra 3[1][8] | 120 °C maximum (manufacturer claim)[5][6] |
| Heat-up time to 60°C (measured preferred) | Anycubic claims the ultra-large hotbed heats up in 125 s; no target temperature is stated for that figure and it is a manufacturer claim, not a measurement[1] | Not documented |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | LeviQ 3.0 auto-levelling with Z-offset and area levelling[1] | Fully automatic calibration and levelling; FlashForge does not name the probe technology[2] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament detection with auto resume, entanglement detection and power-loss resume[1] | Not documented |
| Multi-material/multi-color capability or official upgrade path | Supports 4- or 8-colour printing with ACE Pro units[1] | Four independent toolheads swapped physically rather than shared through one nozzle, which FlashForge markets as zero purge waste and up to 500% faster multi-colour printing[2][5] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Kobra OS; Anycubic Slicer Next is built on the open-source Orca slicer[1] | Not named by FlashForge. Supported slicers are Flash Studio, Orca-Flashforge and OrcaSlicer[6] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch capacitive touchscreen[1] | Not documented |
| On-device UI capabilities (model preview, per-object controls, etc.) | Touchscreen plus slicer, Anycubic app and USB (print only); AI spaghetti detection and object skip supported[1] | Not documented |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Printer UI, slicing software, Anycubic app and USB drive (print only)[1] | Dual-band Wi-Fi 2.4 GHz + 5 GHz, LAN, USB[5][6] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | 1080p camera at 30 fps. A camera module is also sold separately at $29.90, so verify whether a given SKU ships with it[5][6][3] |
| Materials Support | ||
| Officially supported filament list | PLA, PETG, TPU (TPU is not compatible with the ACE Pro)[1] | Not documented |
| Noise & Power Consumption | ||
| Noise: claimed dB and independently measured dB (distance/method) | 60 dB or less in standard mode - a manufacturer figure with no distance or method stated; markedly higher than the 46-48 dB Anycubic claims for the Kobra S1 and Kobra 4[1][11][12] | Not documented |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[13] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Anycubic Kobra 3 Max product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- Flashforge Creator 5 4-Toolheads product page flashforge.com · 2026-08 · vendor
- Flashforge store search results for Creator 5 (live prices) flashforge.com · 2026-08 · vendor
- Anycubic Kobra 3 Max Shopify product JSON (variant prices and store publish date) store.anycubic.com · 2026-08 · vendor
- Flashforge Creator 5 and Creator 5 Pro launch report 3dprinting.com · 2026-08 · review
- Flashforge Creator 5 and 5 Pro breakdown antonmansson.com · 2026-08 · review
- Anycubic Kobra 2 Max store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 3 Combo product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- Flashforge Creator 5 Pro 4-Toolheads product page flashforge.com · 2026-08 · vendor
- Flashforge printer buyer's guide, 5M to Creator 5 eolasprints.com · 2026-08 · review
- Anycubic Kobra S1 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 4 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor