3D Printing Info

Printer comparison

Anycubic Kobra 3 Max vs ELEGOO Neptune 4 Plus

Compare hardware, build volume, printing specifications, dated prices and sources.

Anycubic Kobra 3 Max guideELEGOO Neptune 4 Plus guide

2 selected · all documented properties

Open these two in the interactive comparisonMore Anycubic Kobra 3 Max comparisonsMore ELEGOO Neptune 4 Plus comparisons
Anycubic Kobra 3 Max vs ELEGOO Neptune 4 Plus — documented properties and sources
PropertyAnycubic Kobra 3 MaxBEDSLINGERELEGOO Neptune 4 PlusBEDSLINGER
Identity
BrandAnycubicELEGOO
ClassBEDSLINGERBEDSLINGER
Identity & Market
Manufacturer & exact marketed model name (verify the exact product identity first)Anycubic Kobra 3 Max[1]ELEGOO Neptune 4 Plus[2]
Release date (announcement and actual shipping)Listed on the Anycubic store from 19 February 2025 (Shopify publish date)[3]Listed on the ELEGOO US store from 20 September 2023 (Shopify publish date), the same date as the Neptune 4 Max[4][5]
Street price (USD; dated snapshot per entry)$429.00 with a US plug on store.anycubic.com, Aug 2026, against a compare-at price of $699.00 ($493.00 for the EU plug variant)[3]$309.00 on us.elegoo.com, Aug 2026, against a compare-at price of $425.00. Only a Ribbon-Cable printhead variant is listed for the Plus, unlike the Neptune 4 and 4 Max which also offer a Type-C version[4][6][5]
Variants & sibling models — and how to tell them apart (spec-contamination risk)Same 420 x 420 x 500 mm build volume as the older Kobra 2 Max, so build volume will not tell them apart - but the Kobra 3 Max is faster (600 mm/s claimed against 500), runs Kobra OS with multi-colour support and a 4.3-inch touchscreen, and is lighter at 19 kg against 21 kg. Its acceleration ceiling is 10000 mm/s2, half the 20000 mm/s2 of the smaller Kobra 3 - a difference the marketing does not lead with[1][7][8]Middle model of the Neptune 4 family. Against the base Neptune 4: bigger (320 x 320 x 385 mm), but a lower bed ceiling (100 C rather than 110 C) and much lower acceleration (12000 rather than 20000 mm/s2). Against the Max: smaller and lighter (14.4 kg against 18.1 kg) but with a higher bed ceiling (100 C against 85 C) and higher acceleration (12000 against 8000). Its Z drive is 2 lead screws with 2 tie rods, where the Centauri machines use 3 lead screws[2][9][10][11]
Physical & Frame
Build volume X×Y×Z (mm) — advertised vs actually usable420 x 420 x 500 mm, which Anycubic states as 88 L[1]320 x 320 x 385 mm; printing platform 330 x 330 mm[2]
Machine footprint (mm) & clearance needed (cable/spool overhang)706 x 640 x 753 mm[1]533 x 517 x 638 mm; ELEGOO also publishes a maximum size for machine activity of 578 x 750 x 860 mm including rack and tray, so allow 750 mm of depth[2]
Net weight (kg)19 kg[1]14.4 kg net, 16.65 kg gross[2]
Frame construction & materialNot documentedCNC-machined aluminium extrusion frame (Neptune 4 family)[9]
Enclosure: open / enclosed; panel material; door/lidOpen frame, no enclosure[1]Open frame, no enclosure[2]
Kinematics & Motion Hardware
Kinematics (bedslinger i3 / CoreXY / other)Anycubic's table gives the construction as "Gantry System" - a bed-slinger, with dual Y-axis motors added to stop layer misalignment on the large moving bed[1]Cartesian i3 bed-slinger[2]
Z-axis: leadscrew count & type, sync mechanism, anti-backlashNot documentedTwo lead screws with two tie rods[2]
Belts (type, width, e.g. Gates?)Semi-automatic belt tensioning, which Anycubic pairs with motor anti-skip[1]Not documented
Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?)Not documented"Silent Drive (All Axes)" is all ELEGOO publishes; the driver part number is not given on the product page[2]
Speed & Acceleration
Max print speed (claimed, mm/s)600 mm/s maximum print speed (manufacturer claim), 300 mm/s recommended[1]30-500 mm/s printing speed, with 250 mm/s given by ELEGOO as the recommended figure - the 500 mm/s number is a ceiling, not a working speed[2]
Recommended/typical print speed300 mm/s recommended print speed (manufacturer figure)[1]250 mm/s recommended printing speed (manufacturer figure)[2]
Max acceleration (claimed, mm/s²)10000 mm/s2 maximum acceleration - half the ceiling of the smaller Kobra 3, because of the moving mass[1][8]12000 mm/s2 maximum acceleration; default acceleration 5000 mm/s2[2]
Extruder
Type (direct drive / bowden) & design nameDirect drive ("short distance extrusion") with a quick-release hotend[1]Dual-gear direct extruder with 2 fans (the Centauri machines use a 1-fan version)[2][11]
Hotend & Nozzle
Hotend design (proprietary/standard; quick-swap mechanism?)300 C quick-release hotend with an aerospace-grade ceramic composite throat tube; 0.4 mm standard nozzle, expandable to 0.6 and 0.8 mm[1]Brass nozzle, 0.4 mm, with a titanium-alloy heat break[2]
Max nozzle temp claimed AND firmware max temp limit (both values)300 C maximum nozzle temperature[1]300 C claimed max nozzle temperature[2]
Heated Bed & Surface
Max bed temp claimed AND firmware limit90 C maximum hotbed temperature on a PEI spring steel plate - 20 C below the smaller Kobra 3[1][8]100 C max heated bed temperature at 25 C ambient[2]
Heat-up time to 60°C (measured preferred)Anycubic claims the ultra-large hotbed heats up in 125 s; no target temperature is stated for that figure and it is a manufacturer claim, not a measurement[1]Not documented
Bed surface (material, texture, coating), single/double-sidedNot documentedPEI spring steel sheet; ELEGOO notes it is now upgraded to a dual-sided textured PEI + PLA-specific surface[2]
Leveling & Z-Offset
Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe)LeviQ 3.0 auto-levelling with Z-offset and area levelling[1]Manual levelling combined with 121-point auto-levelling[2]
Filament Handling & Detection
Filament runout sensor (type, location)Filament detection with auto resume, entanglement detection and power-loss resume[1]Filament run-out sensor and power-loss recovery; no camera, no clog detection, no auto filament unloading[2]
Multi-material/multi-color capability or official upgrade pathSupports 4- or 8-colour printing with ACE Pro units[1]Not documented
Electronics & Power
Mainboard model & MCU (exact chip markings if teardowns exist)Not documentedELEGOO describes it only as a "Klipper High-Speed Quiet Motherboard" - no board model or MCU is published[2]
Total rated power drawNot documented320 W rated power; 24 V output; 110-120 V / 220-240 V input[2]
Firmware & Openness
Firmware base & current version (Klipper fork / Marlin fork / proprietary)Kobra OS; Anycubic Slicer Next is built on the open-source Orca slicer[1]Klipper (ELEGOO names the system "Klipper" outright for the Neptune 4 Plus, rather than the ELEGOO OS branding used on the Centauri machines)[2][11]
Connectivity, UI & Camera
Display: size, type, touch?4.3-inch capacitive touchscreen[1]4.3-inch colour capacitive touch screen[2]
On-device UI capabilities (model preview, per-object controls, etc.)Touchscreen plus slicer, Anycubic app and USB (print only); AI spaghetti detection and object skip supported[1]Colour capacitive touch UI; ElegooSlicer is recommended, with Orca and Cura also supported[2]
WiFi (band/standard), Ethernet, USB ports, SD/flash-drivePrinter UI, slicing software, Anycubic app and USB drive (print only)[1]USB, LAN and Wi-Fi[2]
Materials Support
Officially supported filament listPLA, PETG, TPU (TPU is not compatible with the ACE Pro)[1]PLA, TPU, PETG, ABS, ASA, Nylon[2]
Noise & Power Consumption
Noise: claimed dB and independently measured dB (distance/method)60 dB or less in standard mode - a manufacturer figure with no distance or method stated; markedly higher than the 46-48 dB Anycubic claims for the Kobra S1 and Kobra 4[1][12][13]Operating sound is published as 65 dB or less - a manufacturer figure with no measuring distance or method given, so it is not comparable with a reviewer's dB reading[2]
Reliability, Support & Ecosystem
Warranty length & support reputation (evidence, not vibes)One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[14]12 months on brand-new machines and parts, but ELEGOO's own table excludes a long list of parts from that: PEI plate / build plate / nozzle kit / PTFE tube / heater / thermistor / hot end / packaging / manual / tools carry no warranty at all, and the extruder, extruder kit and printhead kit get 6 months. Certified pre-owned machines carry no warranty[15]

Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Anycubic Kobra 3 Max product page (Specifications table) store.anycubic.com · 2026-08 · vendor
  2. ELEGOO Neptune 4 Plus product page (full specification table) us.elegoo.com · 2026-08 · vendor
  3. Anycubic Kobra 3 Max Shopify product JSON (variant prices and store publish date) store.anycubic.com · 2026-08 · vendor
  4. ELEGOO Neptune 4 Plus Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  5. ELEGOO Neptune 4 Max Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  6. ELEGOO Neptune 4 Shopify product JSON (variant prices and store publish date) us.elegoo.com · 2026-08 · vendor
  7. Anycubic Kobra 2 Max store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
  8. Anycubic Kobra 3 Combo product page (Specifications table) store.anycubic.com · 2026-08 · vendor
  9. ELEGOO Neptune 4 product page (Specification table) us.elegoo.com · 2026-08 · vendor
  10. ELEGOO Neptune 4 Max product page (Specification table) us.elegoo.com · 2026-08 · vendor
  11. ELEGOO Centauri Carbon product page (full specification table) us.elegoo.com · 2026-08 · vendor
  12. Anycubic Kobra S1 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
  13. Anycubic Kobra 4 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
  14. Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor
  15. ELEGOO Refund & Warranty policy (warranty period table) us.elegoo.com · 2026-08 · vendor