3D Printing InfoPrinter comparison
Anycubic Kobra 2 vs Bambu Lab P2S
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Anycubic Kobra 2 comparisonsMore Bambu Lab P2S comparisons
| Property | Anycubic Kobra 2BEDSLINGER | Bambu Lab P2SCOREXY |
|---|---|---|
| Identity | ||
| Brand | Anycubic | Bambu Lab |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Anycubic Kobra 2[1] | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[2] |
| Release date (announcement and actual shipping) | Listed on the Anycubic store from 15 May 2023 (Shopify publish date)[1] | Not documented |
| Street price (USD; dated snapshot per entry) | $169.00 on store.anycubic.com, Aug 2026, against a compare-at price of $279.00 - the cheapest machine in this file[1] | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[3][4] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Base model of a five-way family that is easy to confuse. All of Kobra 2, Kobra 2 Neo and Kobra 2 Pro share the same 220 x 220 x 250 mm build volume, but their speed ceilings differ: Neo 250 mm/s max / 150 typical, Kobra 2 300 / 200, Kobra 2 Pro 500 / 300. The Plus (320 x 320 x 400 mm) and Max (420 x 420 x 500 mm) are bigger but drop the bed ceiling to 90 C where the three small ones reach 110 C. Anycubic's own note: Kobra 2 firmware must be at V3.0.6 or above for the quoted speed[1][5][6][7][8] | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[2][9] |
| Market position: superseded? successor announced? | Not documented | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 250 x 220 x 220 mm stated HWD, i.e. 220 x 220 x 250 mm in X x Y x Z; Anycubic quotes 12.1 L[1] | 256 x 256 x 256 mm (manufacturer figure)[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 486 x 440 x 435 mm stated as HWD, so the desk footprint is about 440 x 435 mm and the height is 486 mm[1] | 392 x 406 x 478 mm[2] |
| Net weight (kg) | 8.4 kg[1] | 14.9 kg net[2] |
| Frame construction & material | Not documented | Plastic and steel chassis with a plastic and glass outer frame[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bed-slinger with a gantry frame; Anycubic describes double metal spindles with SG15 bearings on the moving axes[1] | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[2][4] |
| Z-axis: leadscrew count & type, sync mechanism, anti-backlash | Double-threaded rod Z axis (dual lead screws)[1] | Not documented |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 300 mm/s maximum print speed (Anycubic Lab figure; firmware V3.0.6 or above required)[1] | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[2] |
| Recommended/typical print speed | 200 mm/s recommended print speed (manufacturer figure) - the number to plan around, not the 300 mm/s headline[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 3000 mm/s2 acceleration (manufacturer figure) - modest next to the 20000 mm/s2 of the current Kobra generation[1][10] | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[2] |
| Max volumetric flow claimed (mm³/s) | Not documented | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[2] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct drive with a dual-geared extrusion structure[1] | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 260 C nozzle temperature ceiling; 0.4 mm replaceable nozzle[1] | 300 C claimed max nozzle temperature[2] |
| Heater cartridge power (W) | 60 W hotend heater (Anycubic states "upgraded extruder power reaches up to 60 watts")[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | 110 C hotbed temperature ceiling[1] | 110 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Anycubic LeviQ 2.0 automatic levelling with smart Z-offset and a user-adjustable Z compensation value[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Filament run-out sensor fitted, with power-loss recovery[1] | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Part-cooling fan rated to 7000 rpm (Anycubic figure)[1] | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[2] |
| Total rated power draw | Not documented | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[11] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour LCD touchscreen[1] | 5-inch 854x480 touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Not documented | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | microSD card[1] | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[2][9] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Modular assembly - Anycubic states 5 pieces in about 10 minutes[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | PLA, ABS, PETG, TPU[1] | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[12] | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[13] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Anycubic Kobra 2 store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- Anycubic Kobra 2 Neo store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 2 Pro store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 2 Plus store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 2 Max store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- Anycubic Kobra 4 product page (Specifications table) store.anycubic.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor