3D Printing InfoPrinter comparison
Anycubic Kobra 2 Pro vs Bambu Lab X2D
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore Anycubic Kobra 2 Pro comparisonsMore Bambu Lab X2D comparisons
| Property | Anycubic Kobra 2 ProBEDSLINGER | Bambu Lab X2DCOREXY |
|---|---|---|
| Identity | ||
| Brand | Anycubic | Bambu Lab |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | Anycubic Kobra 2 Pro[1] | Bambu Lab X2D; spec PDF header "X2D Spec"[2] |
| Release date (announcement and actual shipping) | Listed on the Anycubic store from 2 February 2026 (Shopify publish date for this listing; the model itself is older)[1] | Not documented |
| Street price (USD; dated snapshot per entry) | $309.00 on store.anycubic.com, Aug 2026, with the compare-at price also $309.00[1] | From $649.00 on the Bambu Lab US store, Aug 2026; the compare page shows the same $649 figure[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Same 220 x 220 x 250 mm build volume as the Kobra 2 and Kobra 2 Neo, but Anycubic's own comparison table puts it at 500 mm/s max and 300 mm/s typical against the Kobra 2's 300/200 - the build volume alone will not tell these three apart. It also adds Anycubic APP support, which the base Kobra 2 lacks[1][4][5] | Dual-nozzle machine: a main hotend with a permanent-magnet synchronous extruder motor and an auxiliary hotend with a plain stepper motor, so the two nozzles are not equivalent. Bambu publishes four different build volumes depending on which nozzle is used, and a shorter list of materials for the auxiliary nozzle. Physical dimensions (392x406x478 mm) are shared with the P2S but the X2D is 16.25 kg against the P2S's 14.9 kg[2][6] |
| Market position: superseded? successor announced? | Not documented | Current model, launched into the slot vacated by the discontinued X1-Carbon[3] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 250 x 220 x 220 mm stated HWD, i.e. 220 x 220 x 250 mm; 12.1 L[1] | Main nozzle 256 x 256 x 260 mm; auxiliary nozzle 235.5 x 256 x 256 mm; dual-nozzle printing 235.5 x 256 x 256 mm; total volume for two nozzles 256 x 256 x 260 mm. The sortable figure below is the main-nozzle volume[2] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | 486 x 435 x 463 mm stated HWD - footprint about 435 x 463 mm[1] | 392 x 406 x 478 mm[2] |
| Net weight (kg) | 8.4 kg[1] | 16.25 kg net[2] |
| Frame construction & material | Not documented | Plastic and steel chassis; plastic, glass and metal outer frame[2] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame, no enclosure[1] | Fully enclosed with a door sensor, active chamber heating to 65 C, and a G3 + H12 HEPA + granulated coconut-shell carbon filter stack with an external exhaust fan[2] |
| Passive chamber temperature reached (if enclosed; measured values preferred) | Not documented | Active chamber heating, maximum 65 C (manufacturer figure)[2] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bed-slinger[1] | CoreXY - not stated in the spec sheet; Bambu groups the X2D with its enclosed CoreXY machines and publishes the same 20000 mm/s2 acceleration figure[2] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 500 mm/s maximum print speed (Anycubic Lab figure)[1] | 1000 mm/s max toolhead speed (manufacturer claim); no independent measurement found[2] |
| Recommended/typical print speed | 300 mm/s typical print speed (manufacturer figure)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | Not documented | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[2] |
| Max volumetric flow claimed (mm³/s) | Not documented | 40 mm3/s, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[2] |
| Vibration Compensation / Input Shaping | ||
| Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary) | One-click vibration compensation that detects X/Y resonance frequencies, plus flow control with retraction and refill compensation[1] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Optimised direct extruder[1] | Two direct-drive extruders: main extruder with hardened-steel gears driven by a Bambu high-precision permanent-magnet synchronous motor, auxiliary extruder with hardened-steel gears driven by a stepper motor[2] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Dual hardened-steel nozzles; 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported; built-in filament cutter[2] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | 260 C nozzle temperature ceiling; 0.4 mm replaceable nozzle[1] | 300 C claimed max nozzle temperature[2] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 120 C max heatbed temperature[2] |
| Bed surface (material, texture, coating), single/double-sided | Not documented | Flexible steel plate, Textured PEI included; Smooth PEI, Cool Plate SuperTack and Engineering Plate supported[2] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Anycubic LeviQ 2.0 automatic levelling with smart Z-offset[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Yes - run-out sensor, tangle sensor and door sensor; odometry with AMS[2] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Not documented | Part-cooling fan, hotend cooling fan, main control board fan, chamber heat-circulation fan, auxiliary part-cooling fan and external exhaust fan, all closed-loop controlled[2] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | Motion controller dual-core Cortex-M4 plus single-core Cortex-M7; application processor quad-core ARM with a dedicated NPU (2 TOPS per the compare page)[2][7] |
| Host computer (SoC, RAM, storage) if firmware runs on embedded Linux | Cortex-A7 1.2 GHz application processor[1] | Not documented |
| Total rated power draw | Not documented | High-voltage version 1600 W at 220 V, low-voltage version 1100 W at 110 V; steady state 250 W printing PLA and 550 W printing PC at 25 C ambient[2] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[8] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | Not documented | 5-inch 1280x720 touchscreen[2] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Supports the Anycubic app (firmware 3.0.5 or later) for online model search, real-time video supervision, online slicing and remote control[1] | Touchscreen plus mobile app and PC app[2] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Not documented | Dual-band Wi-Fi (802.11 a/b/g/n), built-in 8 GB eMMC and a USB port; Ethernet not available, no network kill switch, no 802.1X[2] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | Not documented | Two cameras: live-view 1920x1080 and a toolhead camera at 1600x1200[2] |
| Materials Support | ||
| Officially supported filament list | PLA, ABS, PETG, TPU (Kobra 2 family list)[4] | Main hotend: PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA and carbon/glass-fibre reinforced PLA, PETG, ABS, ASA, PA6, PAHT, PPA, PET. Auxiliary hotend drops PPA-CF/GF and excludes PLA Aero; PLA Silk, PETG-CF, ASA-CF, PA6-CF, TPU for AMS and PA/PET support material are flagged "print with caution" on the auxiliary nozzle[2] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | One year on the complete machine (excluding gifted and second-hand machines), with component warranty periods that vary by part; the period starts on the delivery date and is suspended while a replacement is in transit. Anycubic states it will follow longer local statutory periods where they apply[9] | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[10] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- Anycubic Kobra 2 Pro store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Bambu Lab X2D Spec (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Anycubic Kobra 2 store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Anycubic Kobra 2 Plus store page and Shopify product JSON (Tech Specs block, price, store publish date) store.anycubic.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab - Compare all 3D printers (A2L / X2D / H2C columns) bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Anycubic refund and warranty policy store.anycubic.com · 2026-08 · vendor
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor