3D Printing InfoPrinter comparison
AnkerMake M5 vs Voron 2.4
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
| Property | AnkerMake M5BEDSLINGER | Voron 2.4COREXY |
|---|---|---|
| Identity | ||
| Brand | AnkerMake | Voron Design |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | AnkerMake M5. AnkerMake has since been rebranded eufyMake, and ankermake.com now redirects to eufymake.com[1][2] | Voron 2.4, current revision R2, kits shipping as Rev D and Rev D+. Sold as "Voron 2.4 R2 (Rev D+) 3D Printer Kit by LDO"[3][4] |
| Street price (USD; dated snapshot per entry) | Not documented | $1,399.99 for the LDO Rev D+ kit at Fabreeko (300 mm and 350 mm are the same price), on pre-order with a mid-September estimate, checked Aug 2026. Fabreeko's live feed shows the base 2.4 kit listing at $1,299.99 and available. 3DJake lists an LDO 350 RevD kit but will not ship to the US[3][5][6] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Paired with the cheaper M5C, which is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s) but no screen, no camera and no AI recognition. The M5's headline 500 mm/s is a high-speed-mode figure; its default is 250 mm/s[1][7][2] | Sizes 250, 300 and 350 mm; LDO ships Rev D and Rev D+. Colours black, space grey, blue. Do not confuse with the Trident: the 2.4 lifts the whole gantry on four belted Z motors, the Trident lifts the bed on three screws. The Rev D+ kit includes a Raspberry Pi 4B; the older 3DJake-listed RevD kit explicitly does not include a Pi[3][4][6][8] |
| Market position: superseded? successor announced? | 3DJake lists the M5 as sold out and no longer stocked. The brand has been folded into eufyMake[1][2] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 235 x 235 x 250 mm[1][2] | 300 x 300 x 300 mm or 350 x 350 x 350 mm. Sortable value is the 350 mm kit[3][4][6] |
| Frame construction & material | Not documented | Blind-joint aluminium-extrusion frame with a complete panel set; stainless-steel linear rails throughout[4][6] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame[1] | Enclosed by the supplied panel set. A Nevermore Micro V5 internal circulation filter is included in the LDO kit[6] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | CoreXY on linear rails, with a belted flying gantry on four Z motors[4][3] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | LDO Leviathan board: 5 x TMC2209 plus 2 x TMC5160 HV-capable drivers, ready for 48 V upgrades[3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[1] | Not documented |
| Max acceleration (claimed, mm/s²) | 5,000 mm/s2 in high-speed mode (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 24 mm3/s (manufacturer claim)[2] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder[1] | Clockwork 2 with a Bondtech BMG / Integrated Drive Gear Assembly, in a Stealthburner toolhead[3][4][6] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | E3D Revo Voron (24 V), all-metal, high-flow variant in the Rev D+ kit, with a 60 W heater; upgradeable to a Phaetus Rapido HF for $9.99[3][4][6] |
| Heater cartridge power (W) | 60 W heating block, quoted by AnkerMake as reaching 200 °C[1] | 60 W (E3D Revo High Flow heater)[3] |
| Heated Bed & Surface | ||
| Bed surface (material, texture, coating), single/double-sided | Scratch-resistant PEI-coated magnetic build plate[1] | Cast 5083 aluminium plate with a magnetic base and a powder-coated PEI sheet; LDO silicone bed heater with edge-to-edge heating[4][3][6] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 7 x 7 levelling; probe technology not named[1] | Omron inductive probe supplied; Klicky-mod parts included. Voron Tap is available as an add-on rather than standard[3][4] |
| Mesh grid size (probe point count — firmware evidence) | 49 points (7 x 7)[1] | Not documented |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | LDO x Voron Leviathan mainboard (replacing the earlier BTT Octopus), plus a Nitehawk SB USB toolhead PCB[4][3][6] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Klipper, hosted on a Raspberry Pi 4B (included in the Fabreeko Rev D+ kit, not in the older 3DJake RevD kit)[3][4][6] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour LCD touchscreen[1] | 4.3-inch touchscreen included in the LDO kit[6] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi and USB-C[1] | Not documented |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | 1080p camera with AI recognition and time-lapse[1][2] | Not documented |
| LED chamber/toolhead lighting | Not documented | COB LED strips included[3][6] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Assembly kit; AnkerMake quotes about 15 minutes[1] | Self-assembly kit; some parts must be printed by the user, and the LDO kit supplies pre-cut, pre-crimped cables and a heat-set insert soldering tip[6] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Print accuracy quoted at 0.1 mm (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
- AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
- Voron 2.4 R2 (Rev D+) kit by LDO fabreeko.com · 2026-08 · vendor
- LDO Voron 2.4 R2 (Rev D) kit listing matterhackers.com · 2026-08 · vendor
- Fabreeko Voron collection product feed (live prices) fabreeko.com · 2026-08 · vendor
- LDO Motors Voron 2.4 350 RevD kit contents 3djake.com · 2026-08 · vendor
- AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor
- Voron Trident R2 kit by LDO fabreeko.com · 2026-08 · vendor