3D Printing InfoPrinter comparison
AnkerMake M5 vs LulzBot TAZ Pro
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore AnkerMake M5 comparisonsMore LulzBot TAZ Pro comparisons
| Property | AnkerMake M5BEDSLINGER | LulzBot TAZ ProBEDSLINGER |
|---|---|---|
| Identity | ||
| Brand | AnkerMake | LulzBot |
| Class | BEDSLINGER | BEDSLINGER |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | AnkerMake M5. AnkerMake has since been rebranded eufyMake, and ankermake.com now redirects to eufymake.com[1][2] | LulzBot TAZ Pro (LulzBot's own store lists it under Legacy LulzBot printers)[3] |
| Street price (USD; dated snapshot per entry) | Not documented | $4,950.00 on buy.lulzbot.com, in stock, checked Aug 2026[3] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Paired with the cheaper M5C, which is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s) but no screen, no camera and no AI recognition. The M5's headline 500 mm/s is a high-speed-mode figure; its default is 250 mm/s[1][4][2] | Several TAZ Pro derivatives exist and their specs differ substantially: TAZ Pro S, TAZ Pro XT+, and TAZ Pro Long Bed (282 x 582 x 285 mm, 1.2 mm GammaMaster steel nozzle, 80 °C bed cap, 150 mm/s travel, BLTouch 32-point mesh). The base TAZ Pro is 285 mm cubed with a 0.5 mm hardened-steel nozzle, a 110 °C bed and 300 mm/s travel — do not mix the two spec sets[3][5] |
| Market position: superseded? successor announced? | 3DJake lists the M5 as sold out and no longer stocked. The brand has been folded into eufyMake[1][2] | Not documented |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 235 x 235 x 250 mm[1][2] | 285 x 285 x 285 mm[3] |
| Frame construction & material | Not documented | Open frame; movement on GT2 belts with Igus SST rods and polymer bushings[3] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame[1] | Open frame, no enclosure[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | Cartesian bedslinger[3] |
| Belts (type, width, e.g. Gates?) | Not documented | GT2 belt drive[3] |
| Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?) | Not documented | Trinamic TMC2130[3] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[1] | Not documented |
| Max travel speed | Not documented | 300 mm/s maximum travel speed (manufacturer figure)[3] |
| Max acceleration (claimed, mm/s²) | 5,000 mm/s2 in high-speed mode (manufacturer claim)[1] | Not documented |
| Max volumetric flow claimed (mm³/s) | 24 mm3/s (manufacturer claim)[2] | Not documented |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder[1] | Pro Dual Extruder tool head — two active-lifting hot ends for true dual-material printing[3] |
| Filament diameter | Not documented | 2.85 mm standard, 1.75 mm optional[3] |
| Hotend & Nozzle | ||
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | 290 °C maximum hot end temperature[3] |
| Heater cartridge power (W) | 60 W heating block, quoted by AnkerMake as reaching 200 °C[1] | Not documented |
| Stock nozzle size & sizes included in box | Not documented | 0.5 mm hardened steel[3] |
| Stock nozzle material (brass / hardened steel / plated copper / composite tip) | Not documented | Hardened steel[3] |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 110 °C maximum bed temperature[3] |
| Bed heater type (DC/AC mains) & wattage | Not documented | 360 W, 24 V silicone bed heater[3] |
| Bed surface (material, texture, coating), single/double-sided | Scratch-resistant PEI-coated magnetic build plate[1] | Dual-sided borosilicate glass with PEI film[3] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 7 x 7 levelling; probe technology not named[1] | Automatic 4-point mesh levelling using a 5 V contact circuit, plus automatic X-axis tramming, Z-offset and backlash compensation[3] |
| Mesh grid size (probe point count — firmware evidence) | 49 points (7 x 7)[1] | 4-point mesh[3] |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Filament sensor with both runout and stripping detection[3] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | 32-bit Archim 2.2b with Trinamic TMC2130 drivers[3] |
| PSU (brand, wattage, rail voltage) | Not documented | 500 W 24 V Mean Well, auto-switching, 100-240 VAC input[3] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Marlin[3] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour LCD touchscreen[1] | 5-inch full-colour resistive touchscreen[3] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi and USB-C[1] | USB serial; a 16 GB flash drive is included for standalone printing[3] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | 1080p camera with AI recognition and time-lapse[1][2] | Not documented |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Assembly kit; AnkerMake quotes about 15 minutes[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Not documented | PLA, TPU, ABS, PETG, PVA, PVB, nylon, PC and other materials below 290 °C[3] |
| Safety | ||
| Certifications (UL/ETL/CE/FCC — verify, don't assume) | Not documented | FCC, CE, RCM, ETL, CSA, OSHWA and WEEE. The OSHWA listing is the open-hardware certification[3] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 1 year standard, with extended options. Made in the USA[3] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Print accuracy quoted at 0.1 mm (manufacturer specification, not an independent measurement)[1] | Positional resolution 0.01 mm in X/Y and 0.002 mm in Z (manufacturer specification, not an independent measurement)[3] |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
- AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
- LulzBot TAZ Pro product page buy.lulzbot.com · 2026-08 · vendor
- AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor
- LulzBot TAZ Pro Long Bed 3D Printer listing matterhackers.com · 2026-08 · vendor