3D Printing InfoPrinter comparison
AnkerMake M5 vs Bambu Lab P2S
Compare hardware, build volume, printing specifications, dated prices and sources.
2 selected · all documented properties
Open these two in the interactive comparisonMore AnkerMake M5 comparisonsMore Bambu Lab P2S comparisons
| Property | AnkerMake M5BEDSLINGER | Bambu Lab P2SCOREXY |
|---|---|---|
| Identity | ||
| Brand | AnkerMake | Bambu Lab |
| Class | BEDSLINGER | COREXY |
| Identity & Market | ||
| Manufacturer & exact marketed model name (verify the exact product identity first) | AnkerMake M5. AnkerMake has since been rebranded eufyMake, and ankermake.com now redirects to eufymake.com[1][2] | Bambu Lab P2S; spec sheet header "P2S Spec Sheet"[3] |
| Street price (USD; dated snapshot per entry) | Not documented | From $549.00 on the Bambu Lab US store, Aug 2026; the product page shows $749.00 with the P2S Combo variant selected[4][5] |
| Variants & sibling models — and how to tell them apart (spec-contamination risk) | Paired with the cheaper M5C, which is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s) but no screen, no camera and no AI recognition. The M5's headline 500 mm/s is a high-speed-mode figure; its default is 250 mm/s[1][6][2] | Two SKUs: P2S and P2S Combo (with the 2nd-generation AMS, which adds filament drying). Do not carry P1S figures across - the P2S differs on nearly every headline number: 600 vs 500 mm/s, 110 vs 100 C bed, hardened-steel vs stainless nozzle, 5-inch 854x480 touchscreen vs 2.7-inch monochrome, 14.9 vs 12.95 kg, 1920x1080 30 fps camera vs 1280x720 at 0.5 fps[3][7] |
| Market position: superseded? successor announced? | 3DJake lists the M5 as sold out and no longer stocked. The brand has been folded into eufyMake[1][2] | Current model, marketed by Bambu as "The Classic Evolves" - the direct replacement for the P1S, which is still sold below it[4] |
| Physical & Frame | ||
| Build volume X×Y×Z (mm) — advertised vs actually usable | 235 x 235 x 250 mm[1][2] | 256 x 256 x 256 mm (manufacturer figure)[3] |
| Machine footprint (mm) & clearance needed (cable/spool overhang) | Not documented | 392 x 406 x 478 mm[3] |
| Net weight (kg) | Not documented | 14.9 kg net[3] |
| Frame construction & material | Not documented | Plastic and steel chassis with a plastic and glass outer frame[3] |
| Enclosure: open / enclosed; panel material; door/lid | Open frame[1] | Fully enclosed with a door sensor and an activated-carbon (granulated coconut shell) filter with VOC and particulate filtration. No active chamber heater is listed[3] |
| Kinematics & Motion Hardware | ||
| Kinematics (bedslinger i3 / CoreXY / other) | Cartesian bedslinger[1] | CoreXY - Bambu positions the P2S as the successor to the P1S platform. The spec sheet itself does not name the kinematics[3][5] |
| Speed & Acceleration | ||
| Max print speed (claimed, mm/s) | 250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[1] | 600 mm/s max toolhead speed (manufacturer claim); no independent measurement found[3] |
| Max acceleration (claimed, mm/s²) | 5,000 mm/s2 in high-speed mode (manufacturer claim)[1] | 20000 mm/s2 max toolhead acceleration (manufacturer claim)[3] |
| Max volumetric flow claimed (mm³/s) | 24 mm3/s (manufacturer claim)[2] | 40 mm3/s standard-flow hotend, measured by Bambu on a 250 mm round single-wall model in Bambu ABS at 280 C[3] |
| Extruder | ||
| Type (direct drive / bowden) & design name | Direct-drive extruder[1] | Direct drive with hardened-steel extruder gears, driven by a Bambu Lab high-precision permanent-magnet synchronous motor rather than a plain stepper; built-in filament cutter[3] |
| Hotend & Nozzle | ||
| Hotend design (proprietary/standard; quick-swap mechanism?) | Not documented | Hardened-steel nozzle, 0.4 mm included, 0.2/0.4/0.6/0.8 mm supported[3] |
| Max nozzle temp claimed AND firmware max temp limit (both values) | Not documented | 300 C claimed max nozzle temperature[3] |
| Heater cartridge power (W) | 60 W heating block, quoted by AnkerMake as reaching 200 °C[1] | Not documented |
| Heated Bed & Surface | ||
| Max bed temp claimed AND firmware limit | Not documented | 110 C max heatbed temperature[3] |
| Bed surface (material, texture, coating), single/double-sided | Scratch-resistant PEI-coated magnetic build plate[1] | Flexible steel plate; Textured PEI plate included, Smooth PEI Plate and Cool Plate SuperTack supported[3] |
| Leveling & Z-Offset | ||
| Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe) | Automatic 7 x 7 levelling; probe technology not named[1] | Not documented |
| Mesh grid size (probe point count — firmware evidence) | 49 points (7 x 7)[1] | Not documented |
| Filament Handling & Detection | ||
| Filament runout sensor (type, location) | Not documented | Yes - run-out sensor, tangle sensor, door sensor; filament odometry with AMS[3] |
| Cooling & Air Handling | ||
| Part-cooling fan(s): count, size, ducting design | Not documented | Part-cooling fan, hotend cooling fan and auxiliary part-cooling fan, all closed-loop controlled[3] |
| Electronics & Power | ||
| Mainboard model & MCU (exact chip markings if teardowns exist) | Not documented | Motion controller is a dual-core Cortex-M4 plus a single-core Cortex-M7; application processor is a quad-core 1.5 GHz ARM A7 with a 2 TOPS neural processing unit. Board model and chip markings not published[3] |
| Total rated power draw | Not documented | 100-120 VAC / 200-240 VAC 50/60 Hz; max 1200 W at 220 V, 1000 W at 110 V; steady state 200 W printing PLA[3] |
| Firmware & Openness | ||
| Firmware base & current version (Klipper fork / Marlin fork / proprietary) | Not documented | Closed-source proprietary firmware - not a Klipper or Marlin derivative, and no printer-firmware source is published. The bambulab GitHub organisation carries 11 repositories (Bambu Studio, wxWidgets/boost/ffmpeg forks, the wiki); none is printer firmware. Updates are delivered over the air via Bambu Studio / Bambu Handy[8] |
| Connectivity, UI & Camera | ||
| Display: size, type, touch? | 4.3-inch colour LCD touchscreen[1] | 5-inch 854x480 touchscreen[3] |
| On-device UI capabilities (model preview, per-object controls, etc.) | Not documented | Touchscreen plus mobile app and PC app; Bambu markets on-device AI error detection[3] |
| WiFi (band/standard), Ethernet, USB ports, SD/flash-drive | Wi-Fi and USB-C[1] | Dual-band Wi-Fi (802.11 a/b/g/n, 2.4 and 5 GHz), built-in 8 GB eMMC and a USB port. Ethernet not available; no network kill switch and no 802.1X[3] |
| Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps) | 1080p camera with AI recognition and time-lapse[1][2] | Built-in camera, 1920x1080 at 30 fps - a real video-rate camera, unlike the 0.5 fps unit in the P1 series[3][7] |
| Calibration Routines & QoL | ||
| Assembly level & time from unbox to first print | Assembly kit; AnkerMake quotes about 15 minutes[1] | Not documented |
| Materials Support | ||
| Officially supported filament list | Not documented | PLA, PETG, ABS, ASA, TPU, support materials, PET, PA, PC, PVA, PLA-CF, PETG-CF, ABS-GF, ASA-CF, PA6-CF, PA6-GF, PAHT-CF, PPA-CF, PET-CF[3] |
| Reliability, Support & Ecosystem | ||
| Warranty length & support reputation (evidence, not vibes) | Not documented | 2-year limited warranty for consumers in the US, Canada, the EU, Switzerland, Norway and Iceland; 1 year in the rest of the world. Bambu Lab's own policy records the US/Canada term as a 2026 extension from one year to two[9] |
| Independently Measured Performance | ||
| Dimensional accuracy measurements (third-party, with numbers) | Print accuracy quoted at 0.1 mm (manufacturer specification, not an independent measurement)[1] | Not documented |
Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.
Sources for this comparison
- AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
- AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
- Bambu Lab P2S Spec Sheet (PDF) store.bblcdn.com · 2026-08 · doc
- Bambu Lab US Store - 3D Printers collection listing (base prices, Aug 2026) us.store.bambulab.com · 2026-08 · vendor
- Bambu Lab P2S store page us.store.bambulab.com · 2026-08 · vendor
- AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor
- Bambu Lab P1S store page - 'Parameters Comparison' table giving P1P and P1S in separate columns us.store.bambulab.com · 2026-08 · vendor
- GitHub - bambulab organisation repository list (11 repos, checked Aug 2026) github.com · 2026-08 · doc
- Bambu Lab Warranty Policy bambulab.com · 2026-08 · vendor