3D Printing Info

Printer comparison

FlashForge AD5M vs AnkerMake M5

Compare hardware, build volume, printing specifications, dated prices and sources.

FlashForge AD5M guideAnkerMake M5 guide

2 selected · all documented properties

Open these two in the interactive comparisonMore FlashForge AD5M comparisonsMore AnkerMake M5 comparisons
FlashForge AD5M vs AnkerMake M5 — documented properties and sources
PropertyFlashForge AD5MCOREXYAnkerMake M5BEDSLINGER
Identity
BrandFlashForgeAnkerMake
ClassCOREXYBEDSLINGER
Identity & Market
Manufacturer & exact marketed model name (verify the exact product identity first)Zhejiang FlashForge 3D Technology — Adventurer 5M (AD5M), single-extruder open-frame CoreXY[1][2][3]AnkerMake M5. AnkerMake has since been rebranded eufyMake, and ankermake.com now redirects to eufymake.com[4][5]
Release date (announcement and actual shipping)Announced/launched 2023-09-01; shipping units reviewed by 2023-10-18[6][7]Not documented
Launch MSRP (USD)$399[8]Not documented
Street price (USD; dated snapshot per entry)Official store $299.00 (was $399.00, plus "Save an extra $50, discount auto-applied in cart" ⇒ ~$249 effective); US B2B reseller (CDW) $419.99; discount channel floor $127–$157 (AliExpress $127.12 w/ code; DealNews $139 w/ code AFFUS20, expires 2026-08-26; Slickdeals $157); mid-tier resellers $220–$239 (Slickdeals $220.15, STEMfinity $239.00)[9]Not documented
Variants & sibling models — and how to tell them apart (spec-contamination risk)5M (this report): open frame, no camera, no filtration, no aux fan, unpopulated TVOC/servo/power-button headers on the mainboard. 5M Pro: enclosure + door/lid, built-in camera, HEPA+carbon dual-circulation filtration, auxiliary chamber fan, TVOC sensor, filtration servo, larger footprint (3Dnatives lists 380×400×453 mm). AD5X: 4-colour, different model. Robo E4: rebadged 5M.[10]Paired with the cheaper M5C, which is smaller (220x220x250 vs 235x235x250), has a higher flow rate (35 vs 24 mm3/s) but no screen, no camera and no AI recognition. The M5's headline 500 mm/s is a high-speed-mode figure; its default is 250 mm/s[4][11][5]
Market position: superseded? successor announced?Not superseded, and not actually abandoned. Still sold and listed 2026-08-19 in FlashForge's own nav as "Adventurer 5M — The Best Value Entry-Level 3D Printer", alongside AD5M Pro, AD5X (best seller) and the newer Creator 5 / Creator 5 Pro 4-toolhead flagships. No successor to the 5M has been announced (fresh search 2026-08-19: no "Adventurer 6", no replacement). Genuine counter-signal: 3DJake (major EU retailer) shows "Sold out — Our shop no longer sells this product", and deep discounting to ~$139 (A4) is end-of-life channel behaviour.[12][13]3DJake lists the M5 as sold out and no longer stocked. The brand has been folded into eufyMake[4][5]
Physical & Frame
Build volume X×Y×Z (mm) — advertised vs actually usableAdvertised 220 × 220 × 220 mm; measured usable 217 × 217 mm X/Y; firmware travel envelope X/Y −125 → +125 and Z −10 → 230[14]235 x 235 x 250 mm[4][5]
Machine footprint (mm) & clearance needed (cable/spool overhang)363 × 376 × 413 mm (excl. screen & spool holder); 363 × 402 × 448 mm (incl. screen, excl. spool holder). Manual requires ≥ 20 cm clearance front, back, left and right.[15]Not documented
Net weight (kg)10.8 kg[16]Not documented
Frame construction & materialSheet-metal / all-metal chassis with sheet-metal top cover; "CoreXY all metal structure" in retail copy[17]Not documented
Enclosure: open / enclosed; panel material; door/lidOpen frame as shipped. Official Adventurer 5M Enclosure Kit, $39.99 — modular kit where "Some parts require self-printing"; claims odour containment and ABS/ASA/PC support.[18]Open frame[4]
Passive chamber temperature reached (if enclosed; measured values preferred)Not published[19]Not documented
Kinematics & Motion Hardware
Kinematics (bedslinger i3 / CoreXY / other)CoreXY with moving bed on Z (not a bedslinger)[20]Cartesian bedslinger[4]
X-axis guide type (rods / linear rails / V-wheels; size)Smooth linear shaft(s) with upper + lower sleeve (plain) bearings — not MGN linear rails[21]Not documented
Y-axis guide typeSame family: linear shafts (wiki instructs cleaning "X, Y, and Z-axis linear shafts"); Y motion is CoreXY-coupled[22]Not documented
Z-axis: leadscrew count & type, sync mechanism, anti-backlashThree lead screws driven by one belted Z stepper; rotation_distance: 8 ⇒ 8 mm lead/rev. Single Z stepper ⇒ no motorised tilt.[23]Not documented
Belts (type, width, e.g. Gates?)XY "synchronous belt" (toothed), tensioned by a belt-tension adjusting screw on the printer back; CoreXY belts cross for "bi-directional tension balance"[24]Not documented
Stepper motors (frame size, step angle, brand if known)XY/Z frame size and part numbers (not published). Observed: the two CoreXY motors are not identical units ("two different-looking motors", Igor's Lab, base 5M). Firmware run currents: X 0.9 A, Y 0.9 A, Z 0.6 A (hold 0.6), E 0.8 A (hold 0.8), sense_resistor: 0.10. Extruder motor per aftermarket listing: 36 mm pancake, 2-phase, 1.8°, 2.3 V / 1 A, 10-tooth drive gear[23]Not documented
Stepper drivers (exact model e.g. TMC2209; UART/SPI; sensorless homing?)TMC2209 on X, Y, Z, E via UART (uart_pin per driver), interpolate: True. Physical endstops (X eboard:PA15, Y eboard:PB11, Z PB15) ⇒ no sensorless homing; stealthchop_threshold present but commented out ⇒ SpreadCycle by default[25]Not documented
Microstepping / interpolation settings (firmware evidence)Microsteps: 16 on all four steppers, interpolate: True (TMC 256-step interpolation)[26]Not documented
Speed & Acceleration
Max print speed (claimed, mm/s)600 mm/s (product page "Max Printing Speed") vs 10–300 mm/s ("Printing Speed", manual §1.2, with 600 mm/s assigned to *travel*) vs 200 mm/s ("Max Print Speed: 200 mm/s (but optimal quality at 60-100 mm/s)", FlashForge UK blog FAQ)[27]250 mm/s default; 500 mm/s in high-speed mode (manufacturer figures)[4]
Recommended/typical print speedManual 10–300 mm/s; reviewers' working range 200–300 mm/s, quality profiles 250–400 mm/s; FlashForge UK FAQ suggests 60–100 mm/s for "optimal quality"[28]Not documented
Max travel speed600 mm/s claimed and firmware-limited[29]Not documented
Max acceleration (claimed, mm/s²)20 000 mm/s²[30]5,000 mm/s2 in high-speed mode (manufacturer claim)[4]
Firmware velocity limit (`max_velocity` or Marlin equivalent — exact value)Max_velocity: 600 (plus max_z_velocity: 25)[31]Not documented
Firmware acceleration limit (`max_accel` / `DEFAULT_MAX_ACCELERATION` — exact value)Max_accel: 20000 (plus max_z_accel: 500, max_accel_to_decel: 5000)[32]Not documented
Jerk / square-corner-velocity setting (exact value)Firmware default square_corner_velocity: 25; but FlashForge's own slicer profile emits jerk 9 (machine_max_jerk_x/y = 9, with emit_machine_limits_to_gcode = 1), and both community mods force SCV = 9 because stock SCV is broken[33]Not documented
Max volumetric flow claimed (mm³/s)32 mm³/s ("32mm³/s High Flow Nozzle") vs FlashForge's own slicer profiles capping PLA 25 mm³/s / PETG 12 mm³/s[34][13]24 mm3/s (manufacturer claim)[5]
Max volumetric flow independently measured (mm³/s, method)Not published[19]Not documented
Real-world speed benchmarks (e.g. Benchy time from third-party tests)3DBenchy on the base 5M, same reviewer, three profiles — the only apples-to-apples set that exists: 14 min 09 s (modified/speed G-code), 26 min 09 s ("speedboat rules"), 33 min 28 s (normal 0.20 mm profile). Others: 26.8 min (TechGearLab, base); 31 min speed / 52 min quality (printer-hub, base); ~14 min (owner, base). Non-Benchy: Clearance Spinner 1 h 05 m, Z-wobble test 45 m 43 s (Igor's Lab, base); large model 6 h 52 min (Tom's, Pro); full-volume 220³ ASA array 24 h 44 min (3DPrint.com, Pro)[35][36]Not documented
Vibration Compensation / Input Shaping
Input shaping supported? Implementation (Klipper IS / Marlin ZV / proprietary)Yes — genuine Klipper input shaping, with [input_shaper] and [resonance_tester] in the stock config[37]Not documented
Accelerometer: present? model (ADXL345 / LIS2DW12 / …), location(s), countADXL345, one unit, permanently mounted on the toolhead board (eboard), software SPI, rate: 800, axes_map: x, y, z[38]Not documented
Calibration mode: automatic per-print / user-run routine / factory-fixed valuesUser-run routine from the touchscreen — not per-print, not factory-fixed. Results written back to printer.cfg by Klipper SAVE_CONFIG.[39]Not documented
Shaper type & default frequencies (firmware evidence preferred)Shipped (commented) defaults: 2hump_ei @ 47.4 Hz X, mzv @ 46.2 Hz Y. Measured on a real unit: mzv @ 52.4 Hz X, zv @ 47.0 Hz Y. xblax's own AD5M calibration: mzv @ 52.5 Hz X, zv @ 50 Hz Y.[40]Not documented
Effectiveness evidence (ringing/VFA tests from reviews)Clean PLA at 0.2 mm / 250 mm/s; at full 600 mm/s "some minor surface artifacts are visible on close inspection"; 3DPrint.com (Pro) "virtually no skew", consistent/accurate/square; TechGearLab Print Quality 6.7/10[41]Not documented
Extrusion Pressure Control
Pressure advance (Klipper) / linear advance (Marlin) supported?Yes (Klipper pressure advance)[42]Not documented
Enabled by default? Factory value? (firmware evidence)Yes, on by default: pressure_advance: 0.035[43]Not documented
Auto-calibration for PA/LA? How does it work?No. Stock calibration menu offers leveling, vibration test and PID only.[44]Not documented
Any physical nozzle pressure / load-cell extrusion sensing?No. A load cell exists but is a bed-probe sensor, not an extrusion-force sensor.[45]Not documented
Related settings (PA smooth time etc., firmware values)Pressure_advance_smooth_time: 0.040; max_extrude_only_distance: 1500.00; max_extrude_cross_section: 80; [firmware_retraction] absent from stock; Marlin shim M900 K… → SET_PRESSURE_ADVANCE[46]Not documented
Extruder
Type (direct drive / bowden) & design nameDirect drive, single extruder, proprietary FlashForge "Extruder Unit (Filament Feeder)" with clip-in nozzle assembly[47]Direct-drive extruder[4]
Gear ratio & drive gear material(not published). Inference only: rotation_distance: 4.7 with a 10-tooth motor pinion implies roughly a ~5:1 reduction; material not stated anywhere.[48]Not documented
Filament diameter1.75 mm[49]Not documented
Filament path (PTFE-lined? all-metal? reverse bowden?)External PTFE filament guide tube from the rear-mounted spool into the extruder (reverse-bowden feed to a direct-drive head); hotend assembly includes a "throat tube"[50]Not documented
Claimed extrusion force / grip (if published)Not published[19]Not documented
Auto load/unload routineYes, UI-driven; timing changed in firmware 2.7.8 ("Change the filament loading/unloading time")[51]Not documented
Hotend & Nozzle
Hotend design (proprietary/standard; quick-swap mechanism?)Proprietary integrated "Nozzle Assembly": nozzle + heater + thermistor + throat + heat block + heatsink as one replaceable unit, tool-free, released by pressing two red plastic clips/buckles. FlashForge claims "detached in just 3 seconds without any tools" / "patent-designed".[34][23]Not documented
Max nozzle temp claimed AND firmware max temp limit (both values)Claimed 280 °C; firmware [extruder] max_temp: 350; [verify_heater extruder] max_error: 290; the printer's own settings file records extruderType: "0.4-300"[52]Not documented
Heater cartridge power (W)50 W claimed. Heat-up performance measured: 200 °C in 46 s vs FlashForge's claimed 35 s[34][53]60 W heating block, quoted by AnkerMake as reaching 200 °C[4]
Temperature sensor type (thermistor model / thermocouple) & ratingNTC thermistor, Klipper sensor_type: Generic 3950 (100 kΩ B3950-class), read on eboard:PA0[54]Not documented
Stock nozzle size & sizes included in box0.4 mm installed; no spare nozzle — packing list is printer, filament, power cable, screen, spool holder + 2 screws, grease, glue, diagonal pliers, unclogging pin tool, screwdriver, Allen wrenches 2.0/2.5/3.0[55]Not documented
Stock nozzle material (brass / hardened steel / plated copper / composite tip)0.25 mm and 0.4 mm = stainless steel; 0.6 mm and 0.8 mm = "high-strength steel"[56]Not documented
Nozzle mount standard (V6 / MK8 / Unicorn / proprietary) & swap procedureProprietary clip-in cartridge — not V6, not MK8, not Unicorn. Swap = squeeze both clips, pull, click new one in, then re-level[57]Not documented
Available nozzle sizes/materials (official + third-party compatibility)Official 0.25 / 0.4 / 0.6 / 0.8 mm, $35 each. Third-party: ceramic-heater hardened-steel and copper-heatsink clones (Amazon, Innocube3D), plus a Bambu X1 hotend adapter mod[58]Not documented
All-metal hotend? PTFE near melt zone?Not published[19]Not documented
Melt-zone / high-flow design details (CHT-style, length)Marketed as a "32mm³/s High Flow Nozzle"; no geometry disclosed (no CHT/bi-metal/length figures)[59]Not documented
Heated Bed & Surface
Max bed temp claimed AND firmware limit110 °C (manual §1.2 + FlashForge wiki + 3DJake) vs 100 °C (FlashForge.com product page and FlashForge UK buying FAQ). Firmware [heater_bed] max_temp: 130; [verify_heater heater_bed] max_error: 120[1][27][13]Not documented
Bed heater type (DC/AC mains) & wattageDC (24 V rail) heater, driven on mainboard pin PB9; published wattage still — but bounded by measurement at roughly 240–260 W: measured whole-machine peak 320 W while heating nozzle and bed together, minus the 50 W hotend and ~11–26 W base load[53]Not documented
Heat-up time to 60°C (measured preferred)2 min 27 s (measured, base 5M)[53]Not documented
Bed surface (material, texture, coating), single/double-sidedPowder-coated PEI flexible spring-steel plate, textured, single-sided — and it requires glue for PLA/PETG per FlashForge's own manual. Optional plates: PEI film plate (PLA/TPU glue-free) and PC sticker plate (PC/ABS/ASA)[60]Scratch-resistant PEI-coated magnetic build plate[4]
Magnetic removable plate? Spare plate availability & costYes — flexible removable steel plate on a magnetic bed. Official accessory line includes "PEI Textured Build Plate" for AD5M; Partsbuilt stocks build-plate parts. Exact spare-plate price[61]Not documented
Bed thermal uniformity (third-party thermal imaging if available)Measured bed temperature gradient: 2.6 °C[2]Not documented
Leveling & Z-Offset
Auto bed leveling: probe technology (inductive / strain gauge / load cell / touch probe)Load cell / strain gauge under the bed — nozzle-touch probing. Stock implementation: three channel-select pins level_h1/h2/h3 (PG2/PG3/PG4), a level_clear reset pin (PD10), the gauge value read through a MAX31856 SPI ADC exposed as [temperature_sensor weightValue] … gcode_id: W, trigger consumed by [probe] pin: !PB4[62]Automatic 7 x 7 levelling; probe technology not named[4]
Mesh grid size (probe point count — firmware evidence)5 × 5 = 25 probe points, mesh_pps: 3, 3, algorithm: bicubic, bicubic_tension: 0.2, over mesh_min: -105,-105 → mesh_max: 105,105[63]49 points (7 x 7)[4]
Auto Z-offset (nozzle-touch etc.) or manual (paper method)?Automatic, nozzle-touch (same load cell). Stock [probe] z_offset: -0.25. Live Z trim during print in 0.025 mm steps since firmware 2.4.2.[64]Not documented
Manual leveling screws/knobs present?Four screws under the bed exist (mods expose them as screws_tilt_adjust at ±94 mm, screw_thread: CW-M4), but stock firmware provides no screw-tilt routine[65]Not documented
Gantry-leveling / Z-tilt routine?No. One Z stepper belted to three lead screws ⇒ tilt is mechanical, not motorised; no z_tilt/quad_gantry_level in stock or mod configs[66]Not documented
Leveling workflow (forced per print? saved mesh? adaptive mesh?)Mesh is saved (profile MESH_DATA) and re-used. Manual states "The equipment defaults to the leveling operation before each print", but firmware 2.3.6 "Cancel[led] the default checking of leveling in the print preview interface" and the manual elsewhere says PLA-only users need not level every print. Mods add adaptive/KAMP meshing.[67]Not documented
Filament Handling & Detection
Filament runout sensor (type, location)Mechanical switch at the rear filament inlet (manual lists "Filament Detection Sensor" as external component #6). Firmware: [filament_switch_sensor e0_sensor] switch_pin: !PB14, pause_on_runout: False, event_delay: 1.0. A second, unused e1_sensor on PE1 is declared (leftover dual-extruder/AD5X provision).[68]Not documented
Tangle/snag detection (exact mechanism, if any — do not accept marketing wording at face value)None. There is no tangle detection on the AD5M. FlashForge's only claim is a "Filament run-out reminder".[69]Not documented
Clog detection (mechanism, if any)None in stock.[70]Not documented
Filament change support (M600 / UI-driven)UI-driven load/unload/change; M25 pause recognised since firmware 2.3.6; change-pause position adjusted in 2.4.2. Stock config has no M600; mods add it.[71]Not documented
Spool holder location & max spool size; drybox compatibilityExternal, screw-mounted on the rear panel (2 screws), feeding through a PTFE guide tube. Max spool diameter/width[72]Not documented
Multi-material/multi-color capability or official upgrade pathNone, and no official upgrade path for the 5M. FlashForge's multi-colour answer is the AD5X; FlashForge states the AD5M "cannot be converted into an AD5X". Third-party: Co Print KCM set (documented for the 5M Pro).[73]Not documented
Cooling & Air Handling
Part-cooling fan(s): count, size, ducting designOne toolhead part-cooling fan ([fan] pin: eboard:PB5), ducted to both sides of the nozzle[74]Not documented
Auxiliary part-cooling fan?No — Pro only[75]Not documented
Heatbreak/hotend fanYes, one — a 3010 — [heater_fan heat_fan] pin: eboard:PB4, max_power: 1.0, heater: extruder, heater_temp: 50.0[23]Not documented
Chamber/exhaust fan & filtration (activated carbon / HEPA)No filtration and no chamber fan assembly on the base 5M. Config declares Pro hardware (chamber_fan PC6 with enable_pin: PC7, hardware_pwm: True; internal_fan PB8; external_fan PB6). Pro adds HEPA + activated carbon, dual internal/external circulation, with a servo flap to switch modes. Whether the two air-path fan *headers* are populated on the base mainboard is — see note.[76]Not documented
Electronics bay coolingYes — [fan_generic pcb_fan] pin: PB7, physically a 4010 blower cooling the stepper drivers; firmware 2.3.6 "Turn off the PCB fan when idle". Separately, the PSU has its own always-on fan.[23]Not documented
Fan control (PWM? RPM feedback? firmware evidence)PWM software control on all fans; hardware_pwm: True only on the Pro chamber_fan. No tach/RPM feedback anywhere in the config.[77]Not documented
Electronics & Power
Mainboard model & MCU (exact chip markings if teardowns exist)Two microcontrollers, both Nations Technology N32G455 series (Cortex-M4-class, STM32F1-pin-compatible Chinese parts) running at 144 MHz off a 12 MHz reference: mainboard = N32G455xE (/dev/ttyS5), toolhead "eboard" = N32G455xC (/dev/ttyS1), both UART @ 230400 baud, restart_method: command. Shipped MCU blobs: Mainboard-20230831.bin, Eboard-20231012.hex; vendor MCU firmware version 2.2.3 (2.1.9 on the first three releases).[78]Not documented
Host computer (SoC, RAM, storage) if firmware runs on embedded LinuxAllwinner T113-S3, dual-core ARM Cortex-A7, 128 MB RAM, 8 GB eMMC, Linux 5.4-era kernel headers, armhf[79]Not documented
PSU (brand, wattage, rail voltage)350 W (manual, vendor) internal supply with an always-on fan; 24 V rail inferred from the drop-in Mean Well LRS-350-24 swap ("same seating locations"). A component in a base 5M is marked A-350FGF-24 — but the source attributes that marking to the mainboard, not the PSU, so "the PSU part number is A-350FGF-24" is the report's inference, not an observation ⇒ for that specific attribution.[23]Not documented
Input voltage (110/220 V, switch or auto)AC 100–120 V / 200–240 V, 50/60 Hz — no voltage-selector switch documented[80]Not documented
Total rated power draw350 W rated; measured: 130 W steady-state PLA printing, 320 W peak during simultaneous nozzle+bed heat-up[53]Not documented
Expansion headers / spare ports (fans, steppers, GPIO, USB host)Two unused USB headers on the mainboard; unpopulated TVOC, servo, power-button and one unknown header on the base board; one USB-A host port on the printer front; Ethernet[81]Not documented
Firmware & Openness
Firmware base & current version (Klipper fork / Marlin fork / proprietary)Klipper-derived, proprietary vendor UI/app on top. Host klippy is a Klipper ~0.11-era fork; MCU firmware is a Klipper-11 build labelled 2.2.3, unchanged since Jan 2024. Latest version on FlashForge's own release-notes page: 3.1.9-2.2.3-20250807. Actual shipping firmware is far newer: Z-Mod's native-firmware index lists AD5M stock builds up to 5.1.1 (2026-04-17), and Forge-X byte-analysed series images up to 5.1.7 (2026-06-05) pulled from FlashForge's own OTA source. Linux kernel: 5.4.61, byte-identical across stock firmware 2.6.5 → 5.1.x.[82]Not documented
Source code availability (repos, GPL compliance status, last update date)Partial compliance. FlashForge published one GPL repo for this printer: FlashForge/AD5M_Series_Klipper (GPL-3.0, Klipper 0.11.0-era, last push 2024-05-09, 81★). Its entire GitHub org is 3 repos (that one + OrcaSlicer + Orca-Flashforge). No Linux kernel, U-Boot, Buildroot or rootfs sources are published despite shipping a GPL/GPLv2 Linux 5.4.61 system — the community has to pull the matching kernel source from a third-party mirror of the Allwinner T113 vendor BSP (github.com/iLotusK9/linux_kernel_aw_t113, branch 5.4.61) to build anything against it. The published Klipper also appears not to correspond to shipped binaries.[83]Not documented
Root/SSH access: possible? official or community methodPossible, community-only. Two documented routes: (a) flash Z-Mod's Adventurer5M-root.tgz via USB → SSH root/root; (b) g992's method: edit flashforge_init.sh inside a firmware update archive to add a user + overwrite /etc/passwd with uid 0, then connect by telnet on port 23.[82]Not documented
Moonraker / Mainsail / Fluidd or other open API available (stock vs after mods)?Stock: none. No Moonraker, no web UI, no documented open HTTP API. All three mods add Moonraker (7125) + Mainsail + Fluidd.[84]Not documented
Notable community firmware/mods (names, repos, what they add)Xblax/flashforge_ad5m_klipper_mod (433★, GPL-3.0, Buildroot rootfs + upstream Klipper 0.13 + MCU reflash, full init hijack); ghzserg/zmod "Z-Mod" (418★, Apache-2.0, keeps stock Klipper, adds KAMP/PID/IS/belt spectrogram/Telegram/plugins/GuppyScreen/HelixScreen, zmod.link remote access); DrA1ex/ff5m "Forge-X" v1.4.1 (396★, GPL-3.0, extends the Z-Mod lineage, resurrection.py power-loss plugin, Feather UI, ZRAM swap, real-time Klipper scheduling)[85]Not documented
Firmware update mechanism (OTA/USB) & update cadence historyOTA over WiFi (Settings → Firmware update) and USB stick (FAT32, vendor.tgz, no signature check). FlashForge's public changelog lists exactly 17 releases, re-extracted verbatim by curl + regex on 2026-08-19: 2.3.6-2.1.9-20231101, 2.3.7-2.1.9-20231110, 2.4.2-2.1.9-20231201, 2.4.5-2.2.3-20240118, 2.6.5-2.2.3-20240411, 2.6.6-2.2.3-20240428, 2.7.1-2.2.3-20240606, 2.7.2-2.2.3-20240705, 2.7.3-2.2.3-20240829, 2.7.5-2.2.3-20240911, 2.7.6-2.2.3-20241028, 2.7.7-2.2.3-20241122, 2.7.8-2.2.3-20241213, 2.7.9-2.2.3-20241228, 3.1.3-2.2.3-20250107, 3.1.5-2.2.3-20250212, 3.1.9-2.2.3-20250807. At least 6 further AD5M releases shipped but were never published there: 3.2.3 (2025-10-16), 3.2.5 (2025-12-05), 3.2.6 (2025-12-12), 3.2.7 (2025-12-17), 5.0.3 (2026-01-22), 5.1.1 (2026-04-17); series images run to 5.1.7 (2026-06-05).[82]Not documented
G-code flavor & notable custom G-codes/macrosKlipper flavour (gcode_flavor: klipper in FlashForge's own Orca profile). Notable: M900 K<val> → SET_PRESSURE_ADVANCE (Marlin linear-advance shim, in the stock config); M25 pause; M106 P2; [gcode_arcs] resolution: 1 (G2/G3); [exclude_object] added in firmware 2.6.5; M300/M356 beeper macros only via Z-Mod[86]Not documented
Root shell: exact method (official setting toggle / vendor-documented / community exploit / none). Is root persistent across OTA firmware updates, or wiped each update?Community exploit only — no official toggle, no vendor-documented method — but substantially more durable than an earlier draft of this row claimed. Method: write a vendor-format.tgz update archive to a FAT32 USB stick (Adventurer5M-root.tgz, or a hand-edited flashforge_init.sh in any update archive), boot, log in as root. The vendor installer still performs no signature or integrity verification, verified by byte-comparison through stock 5.1.7 (2026-06-05), so the exploit is not a patched hole — it is the permanent shape of FlashForge's update system. Persistence: partial, and predictable. An OTA reverts /etc/shadow and /etc/inittab in the stock rootfs — so a bare rootfs-level root hack is wiped. It does not touch /data (mmcblk0p7), where all three mods live, and it does not touch /opt/klipper. Forge-X states plainly that a stock OTA, including a 3.x → 5.x jump, leaves the mod running.[87]Not documented
Userland: OS base (Debian/Ubuntu/Buildroot/OpenWrt/busybox-only), package manager present (`apt`/`opkg`/`ipkg`/none), CPU architecture (armv7 / aarch64 / mips / x86), and free space on the writable partition. A busybox/no-apt rootfs with a few MB free is a red flag — say so.Stock: vendor Buildroot-style appliance rootfs, BusyBox userland, no system package manager, telnet-capable, /data = mmcblk0p7. Mods: a second Buildroot rootfs in a chroot on /data (xblax /data/.klipper_mod; Forge-X /data/.mod/.forge-x). No apt, opkg, apk or systemd anywhere — but the xblax chroot does ship python3 + pip, plus target binutils. Kernel: Linux 5.4.61 (vermagic=5.4.61 SMP preempt mod_unload ARMv7 p2v8), Allwinner T113 (sun8iw20) vendor BSP, byte-identical across stock firmware 2.6.5 → 5.1.x. Arch: armv7 32-bit hard-float, Cortex-A7, NEON-VFPv4, glibc (arm-buildroot-linux-gnueabihf). RAM: 128 MB total, ~110 MB usable. Storage: 8 GB eMMC; install requires ≥128 MB free on / and ≥512 MB free on /data. Networking userland is genuinely complete: iptables, iproute2, dropbear, ca-certificates, socat, tcpdump, netcat, curl, rsync, git, nfs-utils, vim/nano/screen. /proc/config.gz is present on the stock kernel.[88]Not documented
Native Tailscale feasibility: can `tailscaled` run persistently on-device? Cite concrete evidence — community guides, wiki entries, forum posts, or repos of people actually doing it on THIS model. Note whether it needs `/dev/net/tun` (kernel TUN support) and whether the kernel provides it, plus whether userspace-networking mode is the only option. Distinguish "someone did it" from "should theoretically work."STILL NOT DEMONSTRATED — nobody has published running tailscaled on an AD5M — but the technical path is far better established than an earlier draft of this row concluded. Negative evidence (re-run independently): all three mod repos grep clean for tailscale/wireguard/tun.ko/net/tun; GitHub issue search on all three repos → total_count: 0; fresh 2026-08-19 web searches surface only generic Tailscale-with-Klipper-on-a-Pi advice, nothing on this model. (1) the stock kernel exposes /proc/config.gz, so CONFIG_TUN is a *one-command check* on any rooted unit — it is unpublished, not unknowable; (2) the exact vendor kernel source is public (Allwinner T113 / sun8iw20, branch 5.4.61) and Forge-X publishes a complete, reproducible recipe for building vermagic-exact out-of-tree modules against the stock kernel — and ships two of them (zram.ko, zsmalloc.ko) that the printer insmods at boot; (3) the kernel is byte-identical from firmware 2.6.5 to 5.1.x, so such a module is built once and never rebuilt; (4) iptables and iproute2 are already in the mod chroot (N9). So if TUN is not compiled in, tun.ko is buildable by an established, documented, already-exercised method.[89]Not documented
SSH daemon: present by default or must be installed/enabled? Default credentials if documented. Does an OTA update disable it or reset the password?Not present/enabled on stock as shipped. The stock exploit path uses telnet on port 23, not SSH. Mods install Dropbear (not OpenSSH) — confirmed in xblax's Buildroot config, and consistent with the documented host-key behaviour. Credentials: Z-Mod root image root / root; xblax root / klipper (set at build time: BR2_TARGET_GENERIC_ROOT_PASSWD="klipper"); Forge-X root / root. The stock rootfs does carry a real root entry — root:$1$OnclaLQR$TyysbY8rO.awyp7JldE9K. — byte-identical across every stock firmware from 3.1.3 to 5.1.7, so an OTA restores that hash but never rotates it. Separately, the printer's own settings file contains a web-console credential pair admin / ff123456. Documented failure modes: mods use different SSH host keys, so switching mods triggers host-key mismatches, and "Resource constraints may prevent the SSH service from running".[82]Not documented
Filesystem persistence: is the rootfs read-only or overlay-mounted? Do user-installed binaries and init/systemd services survive reboot and survive firmware updates? Is there a supported place to persist customizations?Stock rootfs is a separate, vendor-owned partition; user customisation lives on /data (mmcblk0p7), and it is read-write and durable. xblax bind-mounts the stock / into its chroot at /mnt/orig_root remounted read-only (escape hatch: the jailbreak command drops you into the host environment). Mod rootfs + config + gcodes + Moonraker DB all live under /data, so they survive reboot and survive vendor OTA updates too, including a 3.x → 5.x jump. Init integration is via vendor-init hooks that live in the stock rootfs (/etc/inittab), which an OTA *does* revert; both mods therefore carry explicit re-hook/OTA-state logic. Supported persistence points: /data/.klipper_mod (xblax), /data/.mod/.forge-x + /opt/config/mod_data + mod_data/user.cfg + mod_data/user.moonraker.conf (Forge-X).[90]Not documented
Connectivity, UI & Camera
Display: size, type, touch?4.3-inch colour touchscreen ("Smart Touch Screen")[91]4.3-inch colour LCD touchscreen[4]
On-device UI capabilities (model preview, per-object controls, etc.)File browser with 3MF thumbnails, multi-plate 3MF, exclude objects, live Z-offset (0.025 mm steps), leveling, vibration test, PID calibration, filament load/unload, filament-detect toggle, sound toggle, firmware update, LAN mode, static IP, printer name/location, screen-protection timer, "continue printing after print completion", automatic shutdown on completion[92]Not documented
WiFi (band/standard), Ethernet, USB ports, SD/flash-driveWiFi 2.4 GHz + 5 GHz (Realtek RTL8821CU — driver 8821cu.ko loaded from the stock rootfs), Ethernet RJ45, USB-A host port on the front, no SD card slot[93]Wi-Fi and USB-C[4]
Cloud service & phone app; LAN-only mode possible?FlashCloud (https://cloud.sz3dp.com/) and Polar Cloud; apps FlashPrint 5, Orca-Flashforge, Flash Maker. LAN Only mode exists (added firmware 2.6.5) but the mobile app does not work in it.[94]Not documented
Camera: built-in / optional? Resolution & framerate (verify — marketing often omits real fps)Base 5M has NO built-in camera. It does officially support an external USB camera, auto-detected since firmware 2.3.6. Pro's built-in camera: 640 × 480; on-device default streaming config is 640 × 480 @ 15 fps.[95]1080p camera with AI recognition and time-lapse[4][5]
Camera features: live monitor, timelapse, AI failure detection (spaghetti detection) — how real is it?Pro: live monitoring via slicer/cloud, automatic photo capture, time-lapse generation, on-printer playback and export. AI/spaghetti failure detection: none — no source claims it.[96]Not documented
LED chamber/toolhead lightingDisputed for the base 5M. Firmware declares a single white LED channel — [led chamber_led] white_pin: PA8, hardware_pwm: False, with brightness in device settings (extruderLight: 100, ledStatus: true) — but that config and settings dump both come from a 5M *Pro*, FlashForge documents no light for the 5M anywhere, and a base-5M owner states the base "lacks LED lights".[97]Not documented
Calibration Routines & QoL
One-touch auto-calibration suite: what exactly does it calibrate?The "one-click auto leveling" routine does: home (Z→X→Y) → preheat bed → wipe the nozzle → probe 25 points with the load cell → compute mesh → set Z offset. Vibration compensation and PID are separate, user-triggered routines.[98]Not documented
PID autotune exposed to user?Yes, added in firmware 2.6.5; manual advises running it "after replacing the nozzle or when the nozzle temperature is abnormal". Factory PID values ship in the config: extruder Kp 20.109 / Ki 1.943 / Kd 52.031; bed Kp 32.79 / Ki 4.970 / Kd 54.118.[99]Not documented
Flow-rate calibration toolingNone on the printer. Slicer-side only (OrcaSlicer's own flow tests).[100]Not documented
Belt tension check/indicatorsA belt-tension adjusting screw on the rear panel; no indicator, gauge or spec value published[101]Not documented
First-layer inspection featuresNozzle wipe before leveling; live Z-offset trim during print. No camera-based first-layer inspection on the base model.[102]Not documented
Skew calibrationNot in stock firmware. [skew_correction] is added only by mods (xblax ships an all-zero placeholder "Fake profile, it must be calibrated if desired"; Forge-X adds [skew_correction] in data.init.cfg).[103]Not documented
Assembly level & time from unbox to first print~12 minutes setup (TechGearLab, measured); 12–15 min (3DTechValley). Assembly: fit the print-head assembly with 2× M3×16 + 2× M3×8 through a cable strain-relief fastener, mount spool holder, install guide tube.[104]Assembly kit; AnkerMake quotes about 15 minutes[4]
Power-Loss & Interruption Recovery
Power-loss recovery: mechanism (how is state saved? capacitor / eeprom / file on shutdown?)Claimed present ("Power Loss Recovery" is a spec-table row and a product-page bullet). Firmware 2.7.3 (2024-08-29) "Add a prompt when resuming printing after a power outage". The device settings file carries a "recover" boolean. The exact state-save mechanism is undocumented — no capacitor is claimed, and no vendor description exists of when/where state is written. Mods implement their own: xblax [power_loss_recovery] writes state on a 30 s interval and on every layer change (save_interval: 30, save_on_layer: True, history_size: 3) and re-probes Z with the load cell on resume; Forge-X uses a resurrection.py plugin; Z-Mod uses ZRESTORE.[105]Not documented
Verified working? Third-party test results; resume seam qualityNobody independently tested it. No reviewer among TechGearLab, Tom's Hardware, 3DPrint.com, 3Dnatives, 3DWithUs, printer-hub or 3DTechValley reported pulling the plug mid-print. Contrary community signal: both Forge-X and Z-Mod list "faulty resume" among the stock Klipper bugs they patch.[106]Not documented
Filament-runout pause/resume behaviorToggleable ("Filament detect"); when enabled "the printer will stop printing if filament runs out mid-print". Klipper itself has pause_on_runout: False, so the vendor app performs the stop/resume, not Klipper. Filament-change pause position adjusted in firmware 2.4.2.[107]Not documented
Materials Support
Officially supported filament listManual §1.2: \*PLA / \*PETG with 0.4 mm; \*TPU / PLA-CF / PETG-CF with 0.6/0.8 mm (\* = recommended). FlashForge product page: "PLA/PETG series recommended" and explicitly "ABS series Filaments is not compatible with the AD5M".[108]Not documented
PLA/PETG/TPU results & constraints (min TPU shore hardness)PLA: clean at 0.2 mm / 250 mm/s. PETG: needed 240 °C (+5 °C) and 40 % fan; FlashForge's own profile runs PETG at 255 °C / bed 70 °C, 12 mm³/s. TPU: works but 30–40 mm/s required; Tom's Hardware had TPU jam under the drive gear, requiring full extruder disassembly. Min TPU shore hardness: — never published.[109]Not documented
ABS/ASA feasibility (enclosure/chamber constraints, warping reports)Officially not supported on the open 5M. Practically: the official $39.99 enclosure kit claims ABS/ASA/PC support, and an owner ran ABS at bed 110 / nozzle 270 on stock firmware (while hitting E0011 MCU errors). 3DTechValley: ABS "frustrating" without an enclosure. Manual Q7 warns ABS releases toxic gases.[18]Not documented
PC / Nylon / CF-filled feasibility (nozzle & extruder wear constraints)CF-filled: officially supported with the 0.6/0.8 mm "high-strength steel" nozzles (PLA-CF, PETG-CF); 3Dnatives printed PA-CF on the Pro. PC: only with enclosure + the separately-sold PC sticker plate. Nylon: no official support, and the 110 °C bed / no heated chamber make it impractical.[110]Not documented
Effective material ceiling given hotend+bed+chamber limits (reasoned, cite limits)PLA, PETG, TPU, PLA-CF, PETG-CF comfortably. ABS/ASA only with the enclosure kit and ventilation, and even then marginal (no active chamber heater, bed caps at 110 °C, no filtration on base). PC and PA: not realistically viable. Reasoning from hard limits: nozzle 280 °C rated (firmware would allow 350, but the thermistor is a Generic 3950 NTC and the assembly is rated 280), bed 110 °C max (100 °C per storefront), no chamber heater, open frame, no filtration.[111]Not documented
Filament profile ecosystem in the recommended slicerOfficial and reasonably complete. FlashForge maintains FlashForge/Orca-Flashforge (pushed 2026-07-18) with machine profiles for all four nozzle sizes of both 5M and 5M Pro, plus FlashForge filament profiles (Generic PLA, HS PLA, PETG…). Recommended slicers: Orca-Flashforge, OrcaSlicer, FlashPrint 5.[112]Not documented
Safety
Thermal runaway protection (verify in firmware source if at all possible)Present but deliberately loosened vs Klipper defaults. Stock config runs Klipper [verify_heater] on both heaters: extruder max_error: 290, check_gain_time: 60, hysteresis: 10, heating_gain: 5; bed max_error: 120, check_gain_time: 180, hysteresis: 10, heating_gain: 5. Klipper's own defaults (read from FlashForge's published source) are hysteresis 5, max_error 120, heating_gain 2, check_gain_time 20 (extruder) / 60 (bed).[113]Not documented
Certifications (UL/ETL/CE/FCC — verify, don't assume)CE / FCC / RoHS / UKCA / "PES" / KC claimed by a major US reseller; an FCC equipment-authorisation record exists for FCC ID 2AKLL-ADM5 ("3D Printer", grantee *Zhejiang Flashforge 3D Technology CO., Ltd.*), distinct from the 5M Pro's 2AKLL-ADM5P. No UL or ETL claim from anyone.[9]Not documented
Hardware safety: fusing, strain reliefs, belt covers, pinch pointsPrint-head cable routed through a cable strain-relief fastener (2× M3×16 + 2× M3×8 at assembly). Open frame ⇒ exposed belts, gantry and hot nozzle; manual mandates ≥20 cm clearance and warns about entanglement (hair, gloves, clothing). PSU terminals behind a plastic cover. Fusing details.[114]Not documented
Firmware safety limits (max temp cutoffs — exact values)Extruder: max_temp: 350, min_temp: -100, verify_heater max_error: 290. Bed: max_temp: 130, min_temp: -100, verify_heater max_error: 120. Shutdown pins: [output_pin power_off] pin: PC14 value:1 shutdown_value:1, [output_pin clear_power_off] pin: PG1. [idle_timeout] timeout: 600. MCU-level default: CONFIG_INITIAL_PINS="!PB9" — the bed heater pin is driven off the instant the mainboard MCU boots.[115]Not documented
Known safety incidents / recalls / fire reports (with sources)None found[19]Not documented
Noise & Power Consumption
Noise: claimed dB and independently measured dB (distance/method)Claimed: FlashForge's own AD5M enclosure-kit page says it "Lowers printing noise from 65dB to 55dB" ⇒ FlashForge itself puts the bare 5M at 65 dB. The "50 dB low-noise / 55 dB standard" figures are 5M Pro claims. Measured on the base 5M (best evidence): 62.3 dB(A) in operation, 41.1 dB(A) at idle, and 54.8 dB(A) from the hotend fan alone with no printing. Other measurements: 50–55 dB at 200–300 mm/s, informal (printer-hub, base); 3DTechValley "about 50-55 dB" (base); Pro: avg 68 / max 79 / min 46 dB (3DPrint.com), and 65 dB door-open / <60 dB door-closed measured "right in front of the printer" (The 3D Printer Bee).[53][18][116][117]Not documented
Silent/quiet mode available?None on the base 5M. "Low-noise mode" is a 5M Pro feature (enclosure-based). TMC stealthchop_threshold lines are commented out in the stock config, so there is no StealthChop quiet mode either.[118]Not documented
Power draw: idle / PLA print / high-temp print (measured preferred)Measured on the base 5M with a wattmeter: idle 11.3 W; standby with motors energised 25.9 W; printing PLA (220 °C / 60 °C bed) 130 W; peak 320 W while heating nozzle and bed simultaneously. PSU rating for comparison: 350 W. No high-temp (PETG/ABS-target) print measurement exists.[53]Not documented
Reliability, Support & Ecosystem
Warranty length & support reputation (evidence, not vibes)12-month warranty on the printer — but only a 3-month warranty on extruder parts. FlashForge product page, verbatim: "a 1-year limited warranty for its 3D printers and a 3-month warranty for extruder parts". Self-modification voids it (manual: "Any modification of the equipment by yourself will void the warranty"). Support scored 8.0/10 by TechGearLab — the machine's best category score. Channels: support@flashforge.com, phone 8:00–17:00; serial number on a barcode at the rear.[1]Not documented
Common failure points (from long-term reviews/forums, with sources)1) Auto-leveling inconsistency — Tom's: "Auto Leveling did not work correctly on each attempt… I had to run the automatic leveling a few times", one failure printed a cube several mm above the plate; GitHub #73 (open, 32 comments) traces it to filament residue on the nozzle. 2) TPU jamming under the extruder drive gear, requiring full extruder teardown (Tom's). 3) Nozzle clogs — FlashForge's own FAQ devotes Q1 to unclogging and ships a pin tool; clogs mean replacing the whole $35 assembly. 4) E0011 / E0017 MCU errors (comm timeout / move-queue overflow) on stock firmware, especially at high temps/speeds — GitHub #203 (42 comments) and #277. 5) Bed adhesion with the stock powder-coated PEI plate on thin first layers; glue effectively required. 6) PSU fan always on (noise). 7) Flaky USB from poor shielding (xblax). 8) WiFi transfers capped ~25 MB (printer-hub). 9) RAM exhaustion if you mod and multitask. 10) Extruder/toolhead flexible flat cable (FFC) damage — added. FlashForge publishes a dedicated wiki procedure, *"Adventurer 5M: Replace the Extruder Cable"*, and the cable is sold as a spare; in GitHub #305 a user chased a phantom "firmware blocks the mod" problem for three weeks before finding the real cause: *"It was the f\*%&ing Flaccid Flexible c\*%&ing Cable again — I was wondering why my camera was dropping in and out. I trimmed a bit off the end of the cable, re-inserted it, boom install."* A degrading toolhead FFC presents as intermittent, misleading faults (failed USB updates, dropped camera, comms errors), which is exactly the kind of failure that gets misdiagnosed as firmware.[119][120][121][122]Not documented
Spare parts availability & pricing (nozzle, hotend, plate, board, belts)Good availability, official + third party. Verified prices: Nozzle Assembly $35.00 (FlashForge, all four sizes); Enclosure Kit $39.99 (FlashForge). Partsbuilt (US) stocks: Mainboard, Build Plate Heater, Build Plate Scale Kit (Leveling Sensor), Extruder Unit (filament feeder), Extruder PCB Board, Nozzle Heating Cable, Extruder Front Cover + fan, belts/pulleys, motors/leadscrews, print surfaces. Also Amazon/AliExpress/3DJake/3DPrima/Smith3D/Innocube3D.[34][18][61][123]Not documented
Community size (subreddit size, wiki quality, Discord/Facebook groups)Strong, GitHub- and Telegram-centred rather than Reddit-centred. Verified repo stats (2026-08-19): xblax/flashforge_ad5m_klipper_mod 433★ / 45 forks / 34 open issues; ghzserg/zmod 418★ / 50 forks; DrA1ex/ff5m 396★ / 37 forks; g992/flashforge-ad5m-5mpro-research 141★; FlashForge/AD5M_Series_Klipper 81★. Active Telegram groups: FF_5M_5M_Pro, FF_ForgeX. Dedicated wikis: wiki.zmod.link, ghzserg.github.io. Reddit subscriber count — reddit.com is not fetchable from this environment.[124]Not documented
Mod/upgrade ecosystemFirmware: xblax Klipper Mod, Z-Mod, Forge-X (with GuppyScreen / HelixScreen / Feather UIs, KAMP adaptive meshing, Moonraker/Mainsail/Fluidd, timelapse, Telegram notifications, OctoEverywhere). Hardware: official $39.99 enclosure kit; Mean Well LRS-350-24 silent PSU swap; external USB camera mod; Bambu Lab X1 hotend adapter (Printables 1002162); drag-chain/cable-management remixes (Printables 785667); hotend holders; external Klipper host via UART tap (destructive); Co Print KCM multi-material (documented on the Pro).[58][125]Not documented
Long-term (6–12 month) reliability reportsThin. Longest structured tests found: 3 months (3DTechValley, base 5M, Mar 2026 — "solid mid-range printer with excellent print quality"); 1 month / "100 % uptime… no significant issues" (3DPrint.com, Pro); a full instrumented test concluding the base 5M "has proven to be as loud as it is reliable" (Igor's Lab, Feb 2025, which also had a noisy fan replaced under warranty by the manufacturer); an owner thread with repeated successful prints (V1E forum, base 5M). No 6–12 month teardown-and-wear report exists.[126][36]Not documented
Independently Measured Performance
Dimensional accuracy measurements (third-party, with numbers)Base 5M: usable build area measured 217 × 217 mm vs 220 advertised (−2.71 % X/Y); physical plate 235 × 235 mm, "220×220 of which can be used"; clearance-spinner test — all parts including the 0.15 mm-tolerance piece moved freely after printing; nickel-fit calibration test "fit nearly perfectly". Pro (delta noted): 100 mm cube → X 99.70 / Y 99.71 / Z 100.02 mm; 135 mm diagonals → XZ 134.5 / YZ 134.45; 150 mm → 149.2; snap-fit held 0.05 mm. Vendor claims: ±0.1 mm on 100 mm cubes; positioning accuracy X/Y 0.0125 mm, Z 0.0025 mm.[35]Print accuracy quoted at 0.1 mm (manufacturer specification, not an independent measurement)[4]
Surface quality / VFA / ringing assessmentsTechGearLab Print Quality 6.7/10 (ranked #5 of 11); 3DPrint.com (Pro): "very consistent, accurate, and square", "virtually no skew", clean overhangs; 3DWithUs (Pro): "all overhangs free of issues"; at 600 mm/s: "minor surface artifacts… visible on close inspection"[127]Not documented
Benchmark print times (source + settings)Base 5M, one reviewer, three profiles: Benchy 14:09 (modified G-code) / 26:09 (speedboat rules) / 33:28 (normal 0.20 mm); Clearance Spinner 1 h 05 m (Bambu PLA Matt); Z-wobble test 45:43 (Extrudr PLA NX2). Other base-5M: 26.8 min (TechGearLab); 31 min speed / 52 min quality (printer-hub); ~14 min (owner). Pro (delta noted): phone stand 2 h 15 m, articulated dragon 18 h 30 m, vase 4 h 45 m (3DTechValley, base); large model 6 h 52 min (Tom's, Pro); 220³ full-volume ASA array 24 h 44 min with "no detectable warping" (3DPrint.com, Pro)[35]Not documented
First-layer consistency reports3DPrint.com (Pro): "first layers have been nearly flawless over the last month", but "first layers on those materials are a tad too close" for ASA/Nylon. Counter-evidence: Tom's had a leveling failure that printed several mm above the platform; printer-hub reports stock-PEI adhesion problems with thin first layers; GitHub #73 (open) attributes mesh error to nozzle residue.[119]Not documented
Review scores from major outlets (list outlet + score + date)TechGearLab: 68/100 overall, ranked #5 of 11, dated 2024-12-23 — subscores Print Quality 6.7/10 (40 %), Ease of Use 7.2/10 (30 %), Print Capabilities 6.0/10 (20 %), Support 8.0/10 (10 %) — re-verified verbatim 2026-08-19. Igor's Lab (base 5M, 2025-02-27, Tim Kutzner): no numeric score or award; verdict "For 299 euros at the time of testing using the above code, you get a compact CoreXY printer, which has proven to be as loud as it is reliable." Tom's Hardware (5M Pro, 2023-10-18): verdict "Fast, but not First" — numeric star rating not recoverable from the saved page. 3DTechValley (base, 2026-03-03): no numeric score; "solid mid-range printer… no longer the obvious choice". 3DPrint.com (Pro, 2024-08-23): no numeric score; recommends for print farms. The 3D Printer Bee (Pro): no numeric score, no date published. 3Dnatives Lab (Pro): no numeric score in the fetched content.[2][7]Not documented

Manufacturer claims, independent measurements, packages and test conditions retain their source wording. FDM linear speed and resin vertical speed use different units and are not directly comparable. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Flashforge Adventurer 5M product page flashforge.com · 2026-08 · vendor
  2. docs/manual.txt:255-257; https://www.flashforge.com/products/adventurer-5m-3d-printer; https://www.techgearlab.com/reviews/cool-gadgets/3d-printer/flashforge-adventurer-5 techgearlab.com · 2026-08 · doc
  3. docs/manual.txt:255-257; https://www.flashforge.com/products/adventurer-5m-3d-printer; https://www.techgearlab.com/reviews/cool-gadgets/3d-printer/flashforge-adventurer-5 printer-hub.ru · 2026-08 · doc
  4. AnkerMake M5 technical data table 3djake.com · 2026-08 · vendor
  5. AnkerMake M5C review and spec summary (eufyMake) eufymake.com · 2026-08 · vendor
  6. https://3dprintbeginner.com/flashforge-adventurer-5m-pro-presentation/; https://www.tomshardware.com/reviews/flashforge-adventurer-5m-pro-3d-printer 3dprintbeginner.com · 2026-08 · doc
  7. https://3dprintbeginner.com/flashforge-adventurer-5m-pro-presentation/; https://www.tomshardware.com/reviews/flashforge-adventurer-5m-pro-3d-printer tomshardware.com · 2026-08 · doc
  8. 3DPrintBeginner (5M $399 / 5M Pro $599); TechGearLab "$399 list" project evidence · 2026-08 · local
  9. FlashForge product page; https://www.cdw.com/product/flashforge-adventurer-5m-3d-printer/7934222 (Mfg # AD5M, $419.99, re-verified by curl 2026-08-19 — page text: "FlashF cdw.com · 2026-08 · doc
  10. firmware/flashforge-ad5m-5mpro-research/photo/readme.md (PCB comparison: TVOC connector, servo connector, power-on section "(*) Not soldered on the base version"); stock project evidence · 2026-08 · local
  11. AnkerMake M5C technical data table 3djake.com · 2026-08 · vendor
  12. Flashforge AD5X multicolour 3D printer product page flashforge.com · 2026-08 · vendor
  13. FlashForge store navigation captured in scratchpad/ffwiki/trouble.html (fetched 2026-08-19); https://www.flashforge.com/products/flashforge-ad5x-3d-printer; https://www.3 3djake.com · 2026-08 · doc
  14. manual §1.2; TechGearLab "217mm × 217mm (approximately 2.71% less than advertised)"; printer-hub "~217 x 217 mm actual"; stock printer.base.cfg L19-20/34-35 position_max: project evidence · 2026-08 · local
  15. manual §1.2 L300-311; docs/manual.txt:202; FlashForge product page; 3DJake "363 × 402 × 448 mm (without spool holder)" project evidence · 2026-08 · local
  16. manual §1.2 (Net Weight 10.8kg) project evidence · 2026-08 · local
  17. FlashForge wiki linear-guide page (references "sheet metal top cover"); TechGearLab; printer-hub project evidence · 2026-08 · local
  18. https://www.flashforge.com/products/adventurer-5m-enclosure-kit; FlashForge product page ("ABS series Filaments is not compatible with the AD5M") flashforge.com · 2026-08 · doc
  19. — project evidence · 2026-08 · local
  20. stock printer.base.cfg L174 kinematics: corexy; FlashForge wiki "CoreXY mechanism … two motors working in unison" project evidence · 2026-08 · local
  21. FlashForge wiki, Linear Guide Maintenance for AD5M Series (fetched 2026-08-19): "Clean the X, Y, and Z-axis linear shafts…"; "clean both sides of the upper and lower slee project evidence · 2026-08 · local
  22. FlashForge wiki Linear Guide Maintenance page; https://wiki.flashforge.com/en/adventurer-series/maintenance/ad5mseries-replace-the-xy-axis-guide-rail&bearing (video-only) wiki.flashforge.com · 2026-08 · doc
  23. stock printer.base.cfg L42-55 ([stepper_z] rotation_distance: 8, position_endstop: 220; max_z_velocity: 25, max_z_accel: 500); FlashForge wiki intro "three lead screws, w igorslab.de · 2026-08 · doc
  24. FlashForge wiki intro (Printer Back: "Belt tension adjusting screw"); https://wiki.flashforge.com/en/adventurer-series/maintenance/ad5mseries-adjust-and-replace-the-xy-ax wiki.flashforge.com · 2026-08 · doc
  25. stock printer.base.cfg L183-213 ([tmc2209 stepper_x] uart_pin: PC2 … run_current: 0.9), L17/32/48 project evidence · 2026-08 · local
  26. stock printer.base.cfg L15, L30, L46, L61, L185/193/201/209 project evidence · 2026-08 · local
  27. FlashForge product page; docs/manual.txt:279-289; https://uk.flashforge.com/blogs/news/flashforge-adventurer-5m-faq-before-buying uk.flashforge.com · 2026-08 · doc
  28. manual §1.2; printer-hub ("quality mode 250-400 mm/s; working speed 200-300 mm/s"); 3DTechValley ("PLA clean at 0.2mm layer, 250 mm/s"); FlashForge UK FAQ project evidence · 2026-08 · local
  29. manual §1.2 Max Travel Speed 600mm/s; stock printer.base.cfg L175 max_velocity: 600; Orca machine_max_speed_x/y = 600 project evidence · 2026-08 · local
  30. FlashForge product page; manual §1.2; stock printer.base.cfg L176 project evidence · 2026-08 · local
  31. stock printer.base.cfg L175, L178 project evidence · 2026-08 · local
  32. stock printer.base.cfg L176-179; Orca machine_max_acceleration_x/y = 20000, _z = 500, _e = 5000 project evidence · 2026-08 · local
  33. stock printer.base.cfg L180; firmware/orca_flashforge_profiles/fdm_adventurer5m_common.json L28-29; firmware/ff5m/tuning.cfg ([printer] square_corner_velocity: 9); firmwa project evidence · 2026-08 · local
  34. https://www.flashforge.com/products/nozzle-assembly; https://www.3djake.com/flashforge/adventurer-5m ("flow rate of 32 mm³/s"); firmware/orca_flashforge_profiles/Flashfor flashforge.com · 2026-08 · doc
  35. https://www.igorslab.de/en/flashforge-adventurer-5m-3d-drucker-im-test/4/ (Benchy 14:09 / 26:09 / 33:28, spinner, Z-wobble; base 5M); TechGearLab; printer-hub; https://fo igorslab.de · 2026-08 · doc
  36. https://www.igorslab.de/en/flashforge-adventurer-5m-3d-drucker-im-test/4/ (Benchy 14:09 / 26:09 / 33:28, spinner, Z-wobble; base 5M); TechGearLab; printer-hub; https://fo forum.v1e.com · 2026-08 · doc
  37. stock printer.cfg L2-6; stock printer.base.cfg L160-165 [resonance_tester] accel_chip:adxl345, min_freq: 5, max_freq: 100, probe_points: 0,0,100 project evidence · 2026-08 · local
  38. stock printer.base.cfg L150-158 ([adxl345] cs_pin: eboard:PA4, spi_speed: 1000000, spi_software_sclk_pin: eboard:PA5 …) project evidence · 2026-08 · local
  39. manual §5.1 "Choose [Leveling] or [Vibration test], click [Start]"; "When to perform vibration compensation: When there is noticeable ghosting and ringing…; After adjusti project evidence · 2026-08 · local
  40. stock printer.cfg L2-6 and L30-34; firmware/flashforge_ad5m_klipper_mod/printer_configs/printer.cfg (shaper_type_x = mzv, shaper_freq_x = 52.5, shaper_type_y = zv, shaper project evidence · 2026-08 · local
  41. 3DTechValley; 3DPrint.com; TechGearLab project evidence · 2026-08 · local
  42. stock printer.base.cfg L74 project evidence · 2026-08 · local
  43. stock printer.base.cfg L74 pressure_advance:0.035 project evidence · 2026-08 · local
  44. manual §5.1; FlashForge wiki release notes 2.6.5 "Add PID calibration" (no PA entry in any release note) project evidence · 2026-08 · local
  45. stock printer.base.cfg L216-239 (level_h1/h2/h3, [temperature_sensor weightValue] sensor_type: MAX31856 … gcode_id: W), L317-321 [probe] pin: !PB4 project evidence · 2026-08 · local
  46. stock printer.base.cfg L75-77, L287-295 project evidence · 2026-08 · local
  47. FlashForge product page ("Extruder: Direct drive; Qty: 1"); manual §1.2; stock printer.base.cfg L57-60 (extruder stepper on eboard) project evidence · 2026-08 · local
  48. stock printer.base.cfg L62 rotation_distance: 4.7; Amazon replacement-motor listing (10-tooth gear) project evidence · 2026-08 · local
  49. stock printer.base.cfg L64 filament_diameter: 1.750 project evidence · 2026-08 · local
  50. manual §2.3 "Installing the Spool Holder and Filament Guide Tube"; manual §1.1 component 6 "Filament Detection Sensor"; nozzle-assembly kit descriptions project evidence · 2026-08 · local
  51. FlashForge wiki firmware release notes (2.7.8-2.2.3-20241213); manual (keep ≥50 mm nozzle-plate distance during loading) project evidence · 2026-08 · local
  52. FlashForge product page & manual §1.2; stock printer.base.cfg L73 max_temp: 350, L94; firmware/flashforge-ad5m-5mpro-research/software/Adventurer5M.json "extruderType" : project evidence · 2026-08 · local
  53. https://www.flashforge.com/products/nozzle-assembly; https://www.igorslab.de/en/flashforge-adventurer-5m-3d-drucker-im-test/6/ ("46 seconds", base 5M, wattmeter-instrumen igorslab.de · 2026-08 · doc
  54. stock printer.base.cfg L66-67 project evidence · 2026-08 · local
  55. manual §1.2; manual §2.2 Packing List (docs/manual.txt:380-415); stock printer.base.cfg L63 nozzle_diameter: 0.400 project evidence · 2026-08 · local
  56. FlashForge wiki intro: "0.25mm and 0.4mm Nozzle are made of stainless steel; 0.6mm and 0.6mm Nozzle are high-strength steel" [sic — second "0.6" is FlashForge's typo for project evidence · 2026-08 · local
  57. FlashForge wiki intro; manual §6.2 item 5 ("After replacing the nozzle, please perform leveling again"); Tom's Hardware project evidence · 2026-08 · local
  58. FlashForge nozzle-assembly page; Amazon B0DLWR7T5C / B0FW3TBSN6 / B0DKNLYGMF; https://www.printables.com/model/1002162-flashforge-adventurer-5m-bambu-lab-x1-hotend-mod printables.com · 2026-08 · doc
  59. FlashForge nozzle-assembly page project evidence · 2026-08 · local
  60. manual §6.1 (docs/manual.txt:891-896): "1. Powder coated PEI plate requires glue and is suitable for printing PLA/PETG/PLA-CF/PETG-CF/ABS/ASA. TPU printing does not requi project evidence · 2026-08 · local
  61. FlashForge accessories nav (captured 2026-08-19); manual §6.1; https://partsbuilt.com/adventurer-5m5m-pro/ partsbuilt.com · 2026-08 · doc
  62. stock printer.base.cfg L216-257 and L317-321; FlashForge wiki intro ("The heated bed has a pressure sensor at its base"; "measuring the relative height between the nozzle project evidence · 2026-08 · local
  63. stock printer.base.cfg L302-312; corroborated by the SAVE_CONFIG mesh in stock printer.cfg L11-28 (x_count = 5, y_count = 5, mesh_x_pps = 3, algo = bicubic) project evidence · 2026-08 · local
  64. stock printer.base.cfg L319 z_offset: -0.25; FlashForge wiki release notes 2.4.2 ("Change the single adjustment unit for Z-offset to 0.025mm"); wiki intro ("No need for l project evidence · 2026-08 · local
  65. Stock printer.base.cfg has no [screws_tilt_adjust]; firmware/flashforge_ad5m_klipper_mod/printer_configs/printer.base.cfg L313-324 adds it (4× M4, ±94) project evidence · 2026-08 · local
  66. stock printer.base.cfg (single [stepper_z], no z_tilt); FlashForge wiki intro project evidence · 2026-08 · local
  67. manual §5.1 (docs/manual.txt:848-858) + evidence/flashforge_ad5m_user_manual_extracts.md; FlashForge wiki release notes 2.3.6 and 2.4.5 ("Add bed preheating before leveli project evidence · 2026-08 · local
  68. stock printer.base.cfg L259-274; manual §1.1 (docs/manual.txt:241); manual §5.2 ("When [Filament detect] is enabled, the printer will stop printing if filament runs out m project evidence · 2026-08 · local
  69. Grep of the full official manual text for `tangl\ project evidence · 2026-08 · local
  70. Stock config has no filament_motion_sensor, no extrusion encoder, no clog macro project evidence · 2026-08 · local
  71. FlashForge wiki release notes 2.3.6 ("Add M25 pause command", "Recognize M106 P2") and 2.4.2; stock printer.base.cfg (only M900 custom macro); firmware/flashforge_ad5m_kl project evidence · 2026-08 · local
  72. manual §1.1 component 5 "Screw Holes for Spool Holder"; manual §2.3; FlashForge wiki intro ("Spool holder mounting hole") project evidence · 2026-08 · local
  73. FlashForge AD5X product page; https://wiki.coprint3d.com/en/Flashforge-Adventurer-5M-Pro-KCM-Set-Installation-Guide; Z-Mod README (multi-spool "Smart COLOR Menu" listed f wiki.coprint3d.com · 2026-08 · doc
  74. stock printer.base.cfg L117-118; FlashForge wiki intro ("a model cooling fan, and the air ducts at both sides ensure comprehensive model cooling") project evidence · 2026-08 · local
  75. FlashForge wiki intro: "Adventurer 5M Pro is additionally equipped with an auxiliary cooling fan"; base PCB lacks the populated Pro fan headers (g992 photo/readme.md) project evidence · 2026-08 · local
  76. stock printer.base.cfg L120-132, L276-282; g992 photo/readme.md items 2, 3, 6, 7 carry "(*) Not soldered on the base version"; FlashForge wiki intro (Pro-only filtration, project evidence · 2026-08 · local
  77. stock printer.base.cfg L117-132 project evidence · 2026-08 · local
  78. stock printer.base.cfg L1-9; firmware/flashforge_ad5m_klipper_mod/build_scripts/components/mcu_configs/ffad5m/mainboard → CONFIG_MACH_N32G455xE=y, CONFIG_MACH_N32G45x=y, project evidence · 2026-08 · local
  79. firmware/flashforge_ad5m_klipper_mod/README.md L38: "All features of the mod run directly on the printer built-in system (Allwinner T113-S3 with 128MB RAM)"; firmware/ff5 project evidence · 2026-08 · local
  80. manual §1.2 line 302 (Input: AC 100~120V/200~240V，50/60Hz，350W); FlashForge product page project evidence · 2026-08 · local
  81. g992 photo/readme.md ("1. USB connector, not used in the basic version"; "8. 1 more free USB! Yay!"); photo/USB_HUB_Connection.png, photo/PDIC_Connection.png; manual §1.1 project evidence · 2026-08 · local
  82. FlashForge wiki firmware release notes; https://wiki.zmod.link/Native_FW/ (re-fetched 2026-08-19 — AD5M: 3.1.3 (2025-01-07), 3.1.9 (2025-08-07), 3.2.3 (2025-10-16), 3.2.5 wiki.zmod.link · 2026-08 · doc
  83. curl https://api.github.com/orgs/FlashForge/repos → FlashForge/OrcaSlicer (pushed 2024-07-10), FlashForge/AD5M_Series_Klipper (2024-05-09), FlashForge/Orca-Flashforge (20 api.github.com · 2026-08 · doc
  84. g992 software/readme.md: "we have not moonraker :("; printer-hub ("ships with Klipper-based firmware without web interface"); firmware/flashforge_ad5m_klipper_mod/README. project evidence · 2026-08 · local
  85. GitHub API repo stats (fetched 2026-08-19); evidence/zmod_readme.md; firmware/ff5m/README.md, version.txt, docs/MOD_COMPARISON.md; firmware/flashforge_ad5m_klipper_mod/RE project evidence · 2026-08 · local
  86. stock printer.base.cfg L284-295; firmware/orca_flashforge_profiles/fdm_adventurer5m_common.json ("gcode_flavor": "klipper", emit_machine_limits_to_gcode: 1); FlashForge w project evidence · 2026-08 · local
  87. firmware/ff5m/docs/FIRMWARE_5x_COMPAT.md — verbatim: "an OTA flash reverts /etc/shadow and /etc/inittab to stock. This is identical to 3.x behavior and does not affect Fo project evidence · 2026-08 · local
  88. firmware/flashforge_ad5m_klipper_mod/docs/LINUX.md: "Klipper Mod is not a conventional Linux distribution… you won't find a package manager or systemd"; "Be aware of the project evidence · 2026-08 · local
  89. Negative evidence, re-verified independently 2026-08-19: grep -ril 'tailscale' firmware/ff5m firmware/flashforge_ad5m_klipper_mod → none; `grep -rn 'net/tun\ project evidence · 2026-08 · local
  90. firmware/flashforge_ad5m_klipper_mod/docs/LINUX.md ("The host system is mounted read-only to /mnt/orig_root. The printer data partition is mounted to /mnt/data… The mod s project evidence · 2026-08 · local
  91. manual §1.2 (Smart Touch Screen 4.3-inch); FlashForge product page project evidence · 2026-08 · local
  92. FlashForge wiki firmware release notes (2.3.6 → 3.1.9, fetched 2026-08-19); manual §5.1-5.2; FlashForge wiki intro ("automatic shutdown upon print completion") project evidence · 2026-08 · local
  93. firmware/flashforge_ad5m_klipper_mod/build_overlays/common/etc/init/init_chroot.sh L11 insmod /mnt/orig_root/lib/modules/8821cu.ko; FlashForge wiki intro ("5G & 2.4G Wi-F project evidence · 2026-08 · local
  94. manual lines 759-813 ("WAN Mode and LAN Only Mode", "b. LAN Only Mode: Enable [LAN Only]", FlashCloud URL, Polar Cloud); manual line 579: "The APP does not support connec project evidence · 2026-08 · local
  95. FlashForge wiki intro ("Adventurer 5M Pro is equipped with a camera"); manual line 577 ("Real-time monitoring is only accessible when a camera is installed"); FlashForge project evidence · 2026-08 · local
  96. FlashForge wiki intro ("The printer automatically captures photos during printing and creates time-lapse videos"); evidence/3dwithus_ad5mpro_review.md; Tom's Hardware project evidence · 2026-08 · local
  97. stock printer.base.cfg L106-108 ([led chamber_led] white_pin: PA8); software/Adventurer5M.json ("printerName" : "Adventurer 5M Pro", "extruderLight" : 100, "ledStatus" : project evidence · 2026-08 · local
  98. stock printer.base.cfg L302-321; FlashForge wiki release notes 2.3.6 ("Add nozzle wiping before auto-leveling") and 2.4.5 ("Add bed preheating before leveling"); manual § project evidence · 2026-08 · local
  99. FlashForge wiki release notes 2.6.5 ("Add PID calibration"); manual §5.1 note; stock printer.base.cfg L68-71, L84-87 project evidence · 2026-08 · local
  100. Manual §5.1 lists only leveling / vibration / PID; no flow entry in any FlashForge release note 2.3.6→3.1.9 project evidence · 2026-08 · local
  101. FlashForge wiki intro ("Belt tension adjusting screw for adjusting the belt tension to an appropriate level"); the belt maintenance wiki page is video-only project evidence · 2026-08 · local
  102. FlashForge wiki release notes 2.3.6, 2.4.2; manual §5.1 project evidence · 2026-08 · local
  103. Stock printer.base.cfg has no [skew_correction]; firmware/flashforge_ad5m_klipper_mod/printer_configs/printer.base.cfg L305 and printer_configs/printer.cfg; firmware/ff5m project evidence · 2026-08 · local
  104. TechGearLab ("Setup Time: 12 minutes"); 3DTechValley ("setup taking 12-15 minutes"); manual §2.x; 3DWithUs: "one of the easiest printers we have set up to date" project evidence · 2026-08 · local
  105. manual §1.2 (Power Loss Recovery √); FlashForge product page ("Power loss recovery"); FlashForge wiki release notes 2.7.3; software/Adventurer5M.json ("recover" : false); project evidence · 2026-08 · local
  106. Searched all 7 reviews above for power-loss testing → none; evidence/zmod_readme.md ("Klipper v11, plagued by bugs (E0011, E0017, incorrect object exclusion, broken SCV, project evidence · 2026-08 · local
  107. manual §5.2 (docs/manual.txt:876-879); stock printer.base.cfg L271-274; FlashForge wiki release notes 2.4.2 project evidence · 2026-08 · local
  108. manual §1.2 Supported Filament; FlashForge product page; FlashForge wiki intro ("Print PLA, PETG with 0.4mm or 0.25mm nozzle; print TPU, PLA-CF and PETG-CF with 0.6mm or project evidence · 2026-08 · local
  109. 3DTechValley; firmware/orca_flashforge_profiles/Flashforge Generic PETG.json (nozzle_temperature: 255, hot_plate_temp: 70, filament_max_volumetric_speed: 12); 3DPrint.com project evidence · 2026-08 · local
  110. manual §1.2; FlashForge wiki intro; manual §6.1 item 3 ("PC sticker platform plate is suitable for printing PC/ABS/ASA"); 3Dnatives (PLA, PETG, ABS, PA-CF tested on the P project evidence · 2026-08 · local
  111. stock printer.base.cfg L73 (max_temp: 350), L66 (Generic 3950), L91 (bed max_temp: 130); manual §1.2 (280 °C / 110 °C); FlashForge product page project evidence · 2026-08 · local
  112. https://github.com/FlashForge/Orca-Flashforge/tree/main/resources/profiles/Flashforge (machine dir lists Flashforge Adventurer 5M 0.25/0.4/0.6/0.8 Nozzle.json, verified v github.com · 2026-08 · doc
  113. stock printer.base.cfg L93-103; firmware/AD5M_Series_Klipper/klippy/extras/verify_heater.py L22-31 (hysteresis', 5., max_error', 120., heating_gain', 2., default_gain_tim project evidence · 2026-08 · local
  114. manual assembly section; docs/manual.txt:12, :161, :181-202; g992 upgrades/silent_psu.md ("terminals at the bottom of the power supply, under the plastic cover") project evidence · 2026-08 · local
  115. stock printer.base.cfg L72-73, L90-91, L93-103, L140-148, L167-168; firmware/flashforge_ad5m_klipper_mod/build_scripts/components/mcu_configs/ffad5m/mainboard (CONFIG_INI project evidence · 2026-08 · local
  116. https://www.igorslab.de/en/flashforge-adventurer-5m-3d-drucker-im-test/6/ (base 5M: "62.3 dB(A) in operation", "41.1 dB(A) at idle", hotend fan "54.8 dB(A), even without 3dprint.com · 2026-08 · doc
  117. https://www.igorslab.de/en/flashforge-adventurer-5m-3d-drucker-im-test/6/ (base 5M: "62.3 dB(A) in operation", "41.1 dB(A) at idle", hotend fan "54.8 dB(A), even without the3dprinterbee.com · 2026-08 · doc
  118. stock printer.base.cfg L189, L197, L205, L213 (#stealthchop_threshold: — all commented); evidence/3dwithus_ad5mpro_review.md project evidence · 2026-08 · local
  119. Tom's Hardware; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/73; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/203; https://github.com/xblax/ github.com · 2026-08 · doc
  120. Tom's Hardware; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/73; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/203; https://github.com/xblax/ github.com · 2026-08 · doc
  121. Tom's Hardware; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/73; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/203; https://github.com/xblax/ github.com · 2026-08 · doc
  122. Tom's Hardware; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/73; https://github.com/xblax/flashforge_ad5m_klipper_mod/issues/203; https://github.com/xblax/ wiki.flashforge.com · 2026-08 · doc
  123. https://www.flashforge.com/products/nozzle-assembly ($35.00); https://www.flashforge.com/products/adventurer-5m-enclosure-kit ($39.99); https://partsbuilt.com/adventurer- eu.flashforge.com · 2026-08 · doc
  124. curl https://api.github.com/repos/{...} (all five, 2026-08-19); evidence/zmod_readme.md (t.me/FF_5M_5M_Pro); firmware/ff5m/docs/FAQ.md (t.me/FF_ForgeX) api.github.com · 2026-08 · doc
  125. evidence/zmod_readme.md; firmware/ff5m/README.md; firmware/flashforge_ad5m_klipper_mod/README.md; g992 upgrades/silent_psu.md, upgrades/klipper_on_ext_cpu.md, README.md; printables.com · 2026-08 · doc
  126. 3DTechValley; 3DPrint.com; https://www.igorslab.de/en/flashforge-adventurer-5m-3d-drucker-im-test/ ("as loud as it is reliable"; fan replaced by manufacturer); https://fo igorslab.de · 2026-08 · doc
  127. TechGearLab; 3DPrint.com; evidence/3dwithus_ad5mpro_review.md; 3DTechValley project evidence · 2026-08 · local