3D Printing Info

Filament comparison

PLA Metal vs PMMA

Compare printing settings, strength, heat resistance, dated prices and sources.

Metal-filled PLA guidePMMA (acrylic) guide

2 selected · all documented properties

Open these two in the interactive comparisonMore PLA Metal comparisonsMore PMMA comparisons
PLA Metal vs PMMA — documented properties and sources
PropertyMetal-filled PLAPLAPMMA (acrylic)ENGINEERING
Market snapshot
Listing priceUSD/kg; dated snapshots$79.69/kg median; $24.99–$94.99/kg across 6 dated product listings$49.99/kg median; $49.99–$49.99/kg across 1 dated product listings
Identity & Market
Base polymer / chemistryPLA loaded with real metal powder — bronze, copper, steel or iron. Bambu Lab's PLA Sparkle TDS states it has "metal particles included in its composition"; its separately sold PLA Metal does not, and the store page says so explicitly[1][2][3][4][5][6]Poly(methyl methacrylate) — acrylic, sold for 3D printing as a transparent glass substitute[7]
Densityg/cm³1.26 (Bambu Lab Sparkle, a trace-metal glitter grade) up to 3.9–4.0 for colorFabb bronze and copper and 2.3 for Proto-pasta steel, ISO 1183[4][1][2][8]Not documented
Typical priceUSD/kg1 kg spools cluster near 78[9][10][3]1 kg spools cluster near 50[11]
Price range across brandsUSD/kg25–95 across brands; Bambu Lab Sparkle 25, Proto-pasta iron 65, colorFabb bronze and copper 84, Proto-pasta steel 95[9][3][10][8]50 at Push Plastic's 1 kg listing; 3 kg spools run the same per kilogram[11]
Market availability1–5Available from several mainstream brands[10][3][8][9]Special order, 1–2 makers worldwide[11]
Spool sizes & diameters1.75 and 2.85 mm; 0.1, 0.5, 0.75, 1 and 1.5 kg spools[12][10]1.75 and 2.85 mm; 1 and 3 kg spools[11]
Typical applicationsDecorative castings and props that are polished or left to patinate; the density gives prints a metallic heft[1][3]Transparent covers and light guides where PC's yellowing or cost rules it out[7]
Printing Parameters
Nozzle temperature°C195–220 (colorFabb bronze and copper); 192 (Proto-pasta iron); 198 (Proto-pasta steel); 190–230 (Bambu Lab Sparkle)[1][3][8][4]Not documented
Bed temperature°C50–60 (colorFabb, Proto-pasta); 35–45 (Bambu Lab)[1][3][4]Not documented
Enclosure / chamber requirement1–5Open frame is fine[1]Not documented
Part cooling fanOn (colorFabb copper); 0–100 % (colorFabb bronze)[1][2]Not documented
Bed surface & adhesion aidGlass plate with glue stick or tape (colorFabb)[1][2]Not documented
Maximum volumetric flow (mm³/s; see test conditions)mm³/s1.6–2.4 at Proto-pasta's 20–30 mm/s for iron and steel, 3.2–8 at colorFabb's 40–100 mm/s, on a 0.4 mm nozzle at 0.2 mm layer[3][8][1][13]Not documented
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; brittle in filament form and slow to print[3][8]Not documented
Extruder requirementProto-pasta advises an extrusion width 0.05 mm larger than the nozzle and warns that feeding is inconsistent below 0.4 mm and on Bowden machines[3][8]Not documented
Hardware Wear & Reliability
Nozzle hardness required1–4Brass acceptable; hardened steel for volume work[3][8]Not documented
Abrasiveness1–5Moderately abrasive — metal fill[3][8]Not documented
Nozzle clog risk1–5Moderate — needs dry filament and a clean nozzle[8]Not documented
Hotend requirementProto-pasta recommends a wear-resistant or larger nozzle for longer service intervals[3][8]Not documented
Other hardware wearProto-pasta warns of more frequent nozzle replacement and first-layer adjustment[3][8]Not documented
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — the PLA matrix takes up 0.40–0.51 % saturated; the metal powder itself does not absorb water[14][15]Not documented
Effect of moisture on strengthPolymaker rates PLA low-sensitivity and publishes no dry-versus-conditioned figures for this grade; absorbed water flashes to steam and shows as bubbling and poor layer adhesion[16]Not documented
Mechanical Properties
Tensile strength (XY)MPa25 (colorFabb copper) and 30 (colorFabb bronze), ISO 527-1A; Bambu Lab Sparkle 39 ± 3 printed XY, ISO 527[1][2][4]Not documented
Young's modulusMPa1940 ± 230 printed XY, ISO 527 (Bambu Lab Sparkle)[4]Not documented
Elongation at break%3–10 (colorFabb copper) and 5–10 (colorFabb bronze), ISO 527-1A; 11.7 for Bambu Lab Sparkle printed XY[1][2][4]Not documented
Flexural strengthMPa75 ± 4 printed XY, ISO 178 (Bambu Lab Sparkle)[4]Not documented
Flexural modulusMPa2350 ± 140 printed XY, ISO 178 (Bambu Lab Sparkle)[4]Not documented
Charpy impact, notchedkJ/m²23.2 ± 2.4 printed XY, ISO 179, notched (Bambu Lab Sparkle)[4]Not documented
Other impact dataIzod notched 4.5 kJ/m² for colorFabb bronzeFill and 10 kJ/m² for copperFill (ISO 180); Charpy unnotched 66.5 kJ/m² for Bambu Lab Sparkle[1][2][4]Not documented
Layer adhesion / Z tensileMPa32 ± 2 printed Z, ISO 527 (Bambu Lab Sparkle)[4]Not documented
Brittleness1–5Brittle — Proto-pasta describes both its iron and steel grades as more brittle than standard PLA in filament form[3][8]Not documented
Creep resistance / sustained load1–5Poor — no metal-filled creep test; plain printed PLA sagged from 12 to 16.2–21.8 mm over 5 days at 1.25 kg[17][18][19]Not documented
Fatigue / repeated-flex resistance1–5Poor — no grade-specific S-N curve; plain printed PLA ran 38 000–49 000 cycles at 30 % of tensile strength and Proto-pasta describes its iron and steel grades as more brittle than standard PLA[20][3][8]Not documented
Elasticity / flexibility1–5Rigid[4]Not documented
Z strength as % of XY%82 by tensile (printed, Bambu Lab Sparkle)[4]Not documented
Thermal Properties
HDT at 0.45 MPa°C55 (ISO 75, 0.45 MPa, Bambu Lab Sparkle)[4]Not documented
HDT at 1.8 MPa°C53 (ISO 75, 1.8 MPa, Bambu Lab Sparkle)[4]Not documented
Glass transition (Tg)°C56 (DSC, Bambu Lab Sparkle)[4]Not documented
Melting point / Vicat°C156 peak melt (DSC, Bambu Lab Sparkle)[4]Not documented
Environment & Chemical
UV resistance1–5Degrades within weeks outdoors[21]Not documented
Outdoor durabilityProto-pasta markets its iron grade as rustable — the iron oxidises deliberately when exposed to moisture[3]Not documented
Electrical & ESD propertiesProto-pasta magnetic iron PLA is ferromagnetic and responds to magnets[3]Not documented
Health & Safety
Fume toxicity1–5Low hazard — minimal VOC and particle emission[22]Not documented
Ventilation / filtration requirement1–5None needed in a normal room[22]Not documented
Post-Processing
Sanding & machiningPolishing is the intended finish — colorFabb and Proto-pasta both sell these grades to be sanded and buffed to a metallic shine[1][2][8]Not documented
Dimensional accuracy & detailcolorFabb notes the metal fill increases die swell, so flow needs raising above plain PLA[2]Not documented
Solvents & Solubility
Soluble inChloroform dissolves the PLA matrix (10 % w/v, 2–4 h at 23 °C) and leaves the filler as loose sludge; laboratory reagent.[23]Acetone, MEK, ethyl and butyl acetate, THF, chloroform and carbon tetrachloride dissolve it; the last two are laboratory reagents.[24]
Softened or crazed byAcetone, ethyl acetate and toluene plasticise the matrix but dissolve <1 % even at 65 °C; acetone submersion crazes parts.[23][25]Alcohols, aliphatic hydrocarbons, oils and phthalate plasticisers craze it, and the threshold falls as stress rises.[24]
Solvent welding & smoothing agentChloroform vapour attacks only the resin fraction, so the filler is left standing proud; no workshop-safe agent exists.[26][25]Dichloromethane acrylic cement (IPS Weld-On 3): 2–5 min soak, 17.2 MPa lap shear at one week. Controlled carcinogen.[27]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. bronzeFill technical data sheet colorFabb · 2026-08 · tds
  2. copperFill technical data sheet colorFabb · 2026-08 · tds
  3. Magnetic Iron PLA — product page and technical data Proto-pasta · 2026-08 · tds
  4. Bambu Filament Technical Data Sheet — PLA Sparkle Bambu Lab · 2026-08 · tds
  5. PLA Metal — product page Bambu Lab US Store · 2026-08 · vendor
  6. Bambu Filament Technical Data Sheet V3.0 — PLA Metal Bambu Lab · 2026-08 · tds
  7. PMMA Filament 1.75mm 1kg — product page Push Plastic · 2026-08 · vendor
  8. Stainless Steel PLA — product page and technical data Proto-pasta · 2026-08 · tds
  9. PLA Sparkle — product page Bambu Lab US Store · 2026-08 · vendor
  10. bronzeFill — product page colorFabb US · 2026-08 · vendor
  11. Push Plastic product catalogue Push Plastic · 2026-08 · vendor
  12. Proto-pasta product catalogue Proto-pasta · 2026-08 · vendor
  13. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  14. Bambu Filament Technical Data Sheet V3.0 — PLA Basic Bambu Lab · 2026-08 · tds
  15. PolyLite PLA Technical Data Sheet V5.4 Polymaker · 2024-11 · tds
  16. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  17. BambuLab PLA Basic vs PLA Tough vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  18. Polymaker PLA Pro vs PLA-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  19. Carbon Fiber PLA vs META-PLA vs PLA+ vs PLA by Sunlu — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  20. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  21. PLA — material guide Prusa Knowledge Base · 2026-08 · doc
  22. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  23. Solubility Study of Ingeo Biopolymer Grades in Common Organic Solvents (NWPD003) NatureWorks · 2019-10 · tds
  24. Chemical resistance of PMMA products Mitsubishi Chemical (Acrypet) · 2026-08 · tds
  25. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  26. Effect of vapour smoothing in trichloromethane on 3D printed PLA — surface, mechanical and chemical structure Pitale, Keche & Chopra, Engineering Research Express 6(4) 045579 · 2024-12 · paper
  27. Weld-On 3 Acrylic Plastic Cement — technical data sheet (shipped as dichloromethane) IPS Corporation · 2002-07 · tds