3D Printing Info

Filament comparison

ABS+ vs PETG-ESD

Compare printing settings, strength, heat resistance, dated prices and sources.

ABS+ / Tough ABS guideESD-safe PETG guide

2 selected · all documented properties

Open these two in the interactive comparisonMore ABS+ comparisonsMore PETG-ESD comparisons
ABS+ vs PETG-ESD — documented properties and sources
PropertyABS+ / Tough ABSABSESD-safe PETGPETG
Market snapshot
Listing priceUSD/kg; dated snapshots$26.49/kg median; $15.99–$29.99/kg across 4 dated product listings$102.99/kg median; $65.98–$140.00/kg across 2 dated product listings
Identity & Market
Base polymer / chemistryABS reformulated for lower warping and a higher glass transition; Polymaker's ABS Pro and ABS Max reach Tg 114.9 and 126.3 °C against 101 °C for PolyLite ABS[1][2][3]PETG compounded with a conductive filler to bring surface resistivity into the static-dissipative range[4][5]
Densityg/cm³1.04 (ABS Pro) and 1.06 (ABS Max), ISO 1183[1][2]1.24 (Fiberon) and 1.28 (3DXTech), ISO 1183[4][5]
Typical priceUSD/kg1 kg spools cluster near 27[6]1 kg-equivalent spools span 66–140; the middle of the market is about 103[6][7]
Price range across brandsUSD/kg16–30 across brands; SUNLU E-ABS 16, Polymaker ABS Pro 25, YXPOLYER ABS Enhanced 28, Polymaker ABS Max 30[6][8][9]66–140 across brands; Fiberon PETG-ESD 66, 3DXSTAT ESD-PETG 140[6][7]
Market availability1–5Available from several mainstream brands[6]Niche, a handful of specialist brands[6][7]
Spool sizes & diameters1.75 and 2.85 mm; 1 kg spools[6]1.75 mm; 0.5, 0.75, 1 and 3 kg spools[6][7]
Typical applicationsLarge enclosure and automotive parts where plain ABS warps or softens too early[1][2]Electronics fixtures, trays and jigs handled around static-sensitive components[4][5]
Printing Parameters
Nozzle temperature°C270–290 (ABS Pro); 270–300 (ABS Max) — 25–35 °C above plain ABS[1][2]250–290 (Fiberon)[4]
Bed temperature°C120 (ABS Max)[2]70–80 (Fiberon); 70 (3DXTech)[4][5]
Enclosure / chamber requirement1–5Enclosure required (passive)[1][2][10]Open frame is fine — Fiberon specifies room-temperature chamber[4]
Bed surface & adhesion aidClean the plate and apply glue; Simplify3D also lists Kapton tape and ABS slurry[10][11]Textured PEI, satin or powder-coated sheets; on smooth PEI a glue stick acts as a release agent[12][13]
Maximum volumetric flow (mm³/s; see test conditions)mm³/sUp to 250 mm/s (ABS Pro) and 200 mm/s (ABS Max), equivalent to 20 and 16 on a 0.4 mm nozzle at 0.2 mm layer[1][2][14]Fiberon rates the material to 500 mm/s, equivalent to 40 on a 0.4 mm nozzle at 0.2 mm layer — a machine-limited headline rather than a measured melt rate[4][14]
Warping tendency1–5High — enclosure needed for reliable large parts[10]Not documented
Bed-adhesion difficulty1–5Needs a specific surface plus adhesive[10]Needs the right surface or a thin adhesive — the problem is releasing the part, not sticking it[12][13]
Stringing / oozing tendency1–5Slight — Polymaker advises 1–2 mm retraction at 20–30 mm/s[15]Moderate — retraction tuning needed; Polymaker names stringing as PETG's common quirk[13]
Overall printing difficulty1–5Intermediate — dry filament and a tuned profile; the hotter nozzle rules out PTFE-lined hotends[1][2]Intermediate — dry filament and a tuned profile; resistivity depends on getting the nozzle temperature right[4]
Hardware Wear & Reliability
Nozzle hardness required1–4Brass fine indefinitely[10]Hardened steel required[4]
Abrasiveness1–5Non-abrasive[10]Moderately abrasive — conductive carbon filler[4]
Nozzle clog risk1–5Low — unfilled ABS compound; no special hot-end required and clogging is not among the listed drawbacks[11][16]Low — 3DXTech lists no special nozzle concerns and no minimum layer height for its ESD-PETG, only a 65 °C pre-dry[17]
Heat-creep / jam sensitivity1–5Slightly sensitive[11]Slightly sensitive[18]
Hotend requirementNo special hot-end required[11]No special hot-end required[18]
Moisture Behaviour
Moisture absorption (hygroscopicity)1–5Moderate — 0.51 % maximum water absorption (ABS Pro)[1]Moderate (0.3–0.8 %) — the PETG matrix reaches 0.40 % saturated at 25 °C / 55 % RH and 3DXTech specifies a 65 °C, 4 h pre-dry[12][17]
Equilibrium moisture content at ~50 % RH%0.51 maximum water absorption (Polymaker ABS Pro)[1]0.41 equilibrium water absorption (Fiberon PETG-ESD)[4]
Drying temperature & time70 °C for 6 h (ABS Max)[2]65 °C for 3 h (Fiberon)[4]
Symptoms when wetBubbling and popping at the nozzle, stringing and a rough surface[19]Bubbling and popping at the nozzle, stringing and a rough surface[19]
Effect of moisture on strengthPolymaker rates ABS moderate-sensitivity and publishes no dry-versus-conditioned figures[19]Polymaker groups PETG with nylon, PVA and TPU as highly hygroscopic; no dry-versus-conditioned strength figures are published for this grade and the loss shows as bubbling and poor layer adhesion[19]
Storage requirementSealed with desiccant; Polymaker rates ABS moderate-sensitivity[19]Sealed with desiccant; Polymaker groups PETG with the highly hygroscopic materials[19][13]
Mechanical Properties
Tensile strength (XY)MPa34.9 (ABS Pro) and 35.7 (ABS Max) printed XY, ISO 527[1][2]36.1 ± 0.9 printed XY, ISO 527 (Fiberon); 3DXTech quotes 50 at break[4][5]
Young's modulusMPa2330 (ABS Pro) and 2320 (ABS Max) printed XY, ISO 527[1][2]1983 ± 75 printed XY, ISO 527 (Fiberon)[4]
Elongation at break%6.7 (ABS Max) and 7.3 (ABS Pro) at break, printed XY, ISO 527[1][2]7.3 ± 0.7 printed XY, ISO 527 (Fiberon); 3DXTech quotes 13 at break[4][5]
Flexural strengthMPa60.1 (ABS Pro) and 63.3 (ABS Max) printed XY, ISO 178[1][2]54.0 ± 2.5 printed XY, ISO 178 (Fiberon)[4]
Flexural modulusMPa2330 (ABS Pro) and 2500 (ABS Max) printed XY, ISO 178[1][2]1651 ± 141 printed XY, ISO 178 (Fiberon)[4]
Charpy impact, notchedkJ/m²10.5 (ABS Max) and 14.5 (ABS Pro) printed XY, ISO 179, notched[1][2]5.7 ± 0.5 printed XY, ISO 179, notched (Fiberon)[4]
Other impact dataNot documentedCharpy unnotched 29.3 ± 2.2 printed XY (Fiberon, ISO 179)[4]
Layer adhesion / Z tensileMPa21.9 (ABS Pro) and 25.4 (ABS Max) printed Z, ISO 527[1][2]20.7 ± 0.6 printed Z, ISO 527 (Fiberon)[4]
Brittleness1–5Tough — absorbs impact, yields before breaking[1][2]Moderate[4]
Creep resistance / sustained load1–5Moderate — no creep test found; Tg of 115 °C (ABS Pro) and 126 °C (ABS Max) keeps room-temperature service far below softening[1][2]Below average — no ESD-grade creep test; unfilled PETG sagged from 12 to 17.1–20.4 mm over 5 days at 1.25 kg[20][21][22][23]
Fatigue / repeated-flex resistance1–5Moderate — no S-N curve found; 6.7–7.3 % elongation and 10.5–14.5 kJ/m² notched Charpy, below unfilled Bambu Lab ABS[1][2][24]Moderate — no ESD-grade S-N curve; unfilled printed PETG ran 79 000–193 000 cycles at 30 % of tensile strength[25]
Elasticity / flexibility1–5Rigid[1]Slightly flexible in thin sections[4]
Z strength as % of XY%63 (ABS Pro) and 71 (ABS Max), printed[1][2]57 (Fiberon, printed Z against XY tensile)[4]
Thermal Properties
HDT at 0.45 MPa°C106.4 (ABS Pro) and 118.1 (ABS Max), ISO 75 at 0.45 MPa[1][2]76 (ISO 75, 0.45 MPa, Fiberon)[4]
HDT at 1.8 MPa°C101.4 (ABS Pro) and 113.1 (ABS Max), ISO 75 at 1.8 MPa[1][2]72 (ISO 75, 1.8 MPa, Fiberon)[4]
Glass transition (Tg)°C114.9 (ABS Pro) and 126.3 (ABS Max), DSC[1][2]77 (Fiberon) and 80 (3DXTech), DSC[4][5]
Melting point / Vicat°CAmorphous — no melting point; Vicat 116.1 (ABS Pro) and 127.4 (ABS Max), ISO 306[1][2]Amorphous — no melting point; Vicat 86 (Fiberon, ISO 306)[4]
Thermal expansion (CTE)µm/m·K86–89 for printed unfilled ABS (fibre Bragg grating, 25–50 °C); no grade-specific measurement published[26]Not documented
Flammability / UL 94Not documentedFlammable; no UL 94 rating published for standard grades[27]
Environment & Chemical
UV resistance1–5Months outdoors before embrittlement[15]Not documented
Chemical resistanceGood against weak acids, weak alkalis, oils and grease; dissolved by acetone[3]Withstands acids, alkalis, oils and UV exposure[13]
Food contactNot food safe — Polymaker cites potential chemical leaching[15]Not certified for food contact as filament[13]
Biodegradability / compostabilityNot biodegradable[15]Not biodegradable[13]
RecyclabilityMechanically recyclable but not accepted in household plastic collection[15]Not accepted in household plastic collection[13]
Electrical & ESD propertiesNot documentedSurface resistivity falls with nozzle temperature: 7.0×10⁶–1.6×10⁷ ohm at 250 °C, 3.2×10⁵–4.7×10⁵ at 270 °C and below 1×10⁴ at 290 °C (Fiberon); 3DXTech quotes 10⁷–10⁹ ohm/sq[4][5]
Health & Safety
Fume toxicity1–5High — hazardous VOC such as styrene; enclosure and filtration needed[28][10]Moderate — measurable VOCs and UFPs, ventilation advised[28]
VOC emission rateµg/min12–113 styrene, the dominant VOC from every ABS and HIPS combination tested[28]Not documented
Ultrafine-particle emission rateparticles/min2 × 10¹⁰ to 9 × 10¹⁰ median across all ABS printers, two orders of magnitude above PLA's ≈1 × 10⁸[28]Not documented
Hazardous species emittedStyrene dominates. Bambu Lab states ABS and ASA release harmful gases such as styrene at printing temperature, which can be toxic and cause dizziness or nausea[28][10]Not documented
Ventilation / filtration requirement1–5Enclosure with carbon and HEPA filtration — an enclosure alone cut measured UFP by only about 35 %[28][10]Open a window / occasional ventilation[28]
Dust & fibre handling hazardNot documentedConductive carbon filler is bound in the matrix; avoid inhaling sanding dust[4]
Post-Processing
Sanding & machiningSands well and takes filler before painting[15]Sands poorly — the material is tough and gums rather than powders[18]
Painting & finishingPaints readily after light abrasion[15]Not documented
Gluing & solvent weldingNot documentedCyanoacrylate; no common solvent welds PETG cleanly[18]
Vapour / chemical smoothingAcetone vapour smoothing works[3]No practical vapour smoothing[18]
Support material pairingHIPS breaks away or dissolves in d-limonene; Bambu Lab sells a dedicated Support for ABS[29][10]Prints its own supports; Polymaker rates PolyDissolve S1 for PETG[18]
Dimensional accuracy & detailNot documentedNozzle temperature has to be held steady — it moves surface resistivity by three orders of magnitude[4]
Solvents & Solubility
Soluble inAcetone dissolves it — the basis of ABS slurry; so do MEK, THF, ethyl acetate, chloroform, dichloromethane and toluene.[30][3]No common workshop solvent; 1,2-dichloroethane destroys it inside a week and dichloromethane — a carcinogen — dissolves the surface.[31][32]
Softened or crazed byPetrol and perchloroethylene soften it and benzene attacks it; d-limonene disrupts layer adhesion in some ABS and ASA grades.[30][33]Acetone (+16 % weight over 1 year at 23 °C), ethyl acetate, toluene and DMF swell and soften it; methanol crazes it.[31]
Solvent welding & smoothing agentAcetone: about 20 min of vapour at 80 °C over 5 mm of liquid. Prusa measured layer adhesion more than doubled.[32]Dichloromethane brushed on is the only agent that smooths PETG — a controlled carcinogen, not workshop stock.[32]

Material entries describe families or representative grades, not an interchangeable specification for every spool. Test methods, orientations and conditions may differ. Unknown values are marked “Not documented”. Prices and source dates remain historical snapshots; check the linked guide for product details. Differences highlight text, not a universal winner.

Sources for this comparison

  1. Polymaker ABS Pro Technical Data Sheet V1 (2026-05-29) Polymaker · 2026-05 · tds
  2. Polymaker ABS Max Technical Data Sheet V1.1 (2026-06-01) Polymaker · 2026-06 · tds
  3. PolyLite ABS Technical Data Sheet (V5.5 served at this URL) Polymaker · 2024-11 · tds
  4. Fiberon PETG-ESD Technical Data Sheet V1.1 Polymaker · 2026-08 · tds
  5. 3DXSTAT ESD-PETG Technical Data Sheet 3DXTech · 2026-08 · tds
  6. Polymaker product catalogue Polymaker · 2026-08 · vendor
  7. 3DXTech product catalogue 3DXTech · 2026-08 · vendor
  8. SUNLU E-ABS (Easy ABS) 3D Printer Filament 1 kg SUNLU · 2026-08 · vendor
  9. YXPOLYER ABS Enhanced product page YXPOLYER · 2026-08 · vendor
  10. ABS / ASA / PC Usage Guide Bambu Lab Wiki · 2026-08 · doc
  11. ABS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  12. Prusament PETG Technical Datasheet v1.1 Prusa Polymers · 2022-02 · tds
  13. PETG — material basics Polymaker Wiki · 2026-08 · doc
  14. Max volumetric speed Prusa Knowledge Base · 2026-08 · doc
  15. ABS — material basics Polymaker Wiki · 2026-08 · doc
  16. Filament Material Guide Prusa Knowledge Base · 2026-08 · doc
  17. 3DXSTAT ESD-PETG — product page (print recommendations) 3DXTech · 2026-08 · doc
  18. PET and PETG — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  19. Wet Filament — signs, causes and drying Polymaker Wiki · 2026-08 · doc
  20. PCTG vs PETG comparison — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  21. Extrudr PETG vs PCTG vs XPETG-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  22. Prusament PETG-CF vs PETG V0 vs PETG — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  23. BambuLab PETG Basic vs Translucent vs PETG-CF — results spreadsheet My Tech Fun (Igor Gaspar) · 2026-08 · test
  24. Bambu Filament Technical Data Sheet V3.0 — ABS Bambu Lab · 2026-08 · tds
  25. Mechanical Properties of Additively Manufactured Polymeric Materials — PLA and PETG — For Biomechanical Applications Polymers 16(13):1868 · 2024-06 · paper
  26. Characterization of Thermal Expansion Coefficient of 3D Printing Polymeric Materials Using Fiber Bragg Grating Sensors Materials 17(18):4668 · 2024-09 · paper
  27. Prusament PETG V0 Technical Datasheet Prusa Polymers · 2026-08 · tds
  28. Emissions of Ultrafine Particles and Volatile Organic Compounds from Commercially Available Desktop Three-Dimensional Printers with Multiple Filaments (Azimi et al.) Environmental Science & Technology 50(3) 1260-1268 · 2016-01 · paper
  29. HIPS — Ultimate 3D Printing Materials Guide Simplify3D · 2026-08 · doc
  30. Chemical resistance — resistance of Ensinger plastics to chemicals (DIN 50 014, 23/50) Ensinger · 2026-08 · tds
  31. Eastman Spectar copolyester — Chemical resistance (unstressed bars, 1 year at 23 °C) Eastman Chemical Company · 2026-08 · tds
  32. Improve your 3D prints with chemical smoothing Prusa Research · 2026-08 · doc
  33. HIPS — Knowledge Base Prusa Research · 2026-08 · doc